Datasheet

3
FN3284.10
June 15, 2006
Absolute Maximum Ratings Thermal Information
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
V
L
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (GND - 0.3V) to (V+) +0.3V
Digital Inputs V
S
, V
D
(Note 1) . . . . . (V-) -2V to (V+) + 2V or 30mA,
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle, Max). . 100mA
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V (Max)
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max)
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min)
Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤20ns
Thermal Resistance (Typical, Note 2) θ
JA
(°C/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Maximum Junction Temperature (Plastic Package). . . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(SOIC and TSSOP- Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on S
X
, D
X
, or IN
X
exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
2. θ
JA
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, V
IN
= 2.4V, 0.8V (Note 3), V
L
= 5V,
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(°C)
(NOTE 4)
MIN
(NOTE 5)
TYP
(NOTE 4)
MAX UNITS
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
R
L
= 300Ω, C
L
= 35pF 25 - 100 150 ns
Turn-OFF Time, t
OFF
25 - 60 100 ns
Break-Before-Make Time Delay (DG403), t
D
R
L
= 300Ω, C
L
= 35pF 25 5 12 - ns
Charge Injection, Q (Figure 3) C
L
= 10nF, V
G
= 0V, R
G
= 0Ω 25 - 60 - pC
OFF Isolation (Figure 4) R
L
= 100Ω, C
L
= 5pF, f = 1MHz 25 - 72 - dB
Crosstalk (Channel-to-Channel) (Figure 6) 25 - -90 - dB
Source OFF Capacitance, C
S(OFF)
f = 1MHz, V
S
= V
D
= 0V (Figure 7) 25 - 12 - pF
Drain OFF Capacitance, C
D(OFF)
25 - 12 - pF
Channel ON Capacitance, C
D(ON)
+ C
S(ON)
25 - 39 - pF
DIGITAL INPUT CHARACTERISTICS
Input Current with V
IN
Low, I
IL
V
IN
Under Test = 0.8V, All Others = 2.4V Full -1 0.005 1 µA
Input Current with V
IN
High, I
IH
V
IN
Under Test = 2.4V, All Others = 0.8V Full -1 0.005 1 µA
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full -15 - 15 V
Drain-Source ON Resistance, r
DS(ON)
V+ = 13.5V, V- = -13.5V,
I
S
= 10mA, V
D
= ±10V
25 - 20 45 Ω
Full - - 55 Ω
r
DS(ON)
Matching Between Channels, ∆r
DS(ON)
V+ = 16.5V, V- = -16.5V,
I
S
= -10mA, V
D
= 5, 0, -5V
25 - 3 3 Ω
Full - - 5 Ω
Source OFF Leakage Current, I
S(OFF)
V+ = 16.5V, V- = -16.5
V
D
= ±15.5V, V
S
= 15.5V
25 -0.5 -0.01 0.5 nA
Full -5 - 5 nA
Drain OFF Leakage Current, I
D(OFF)
25 -0.5 -0.01 0.5 nA
Full -5 - 5 nA
Channel ON Leakage Current, I
D(ON)
+I
S(ON)
V± = ±16.5V, V
D
= V
S
= ±15.5V 25 -1 -0.04 1 nA
Full -10 - 10 nA