Datasheet

2
FN1320.9
October 4, 2005
Absolute Maximum Ratings Thermal Information
Supply Voltage (V+ to V-). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15V
DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . (V+ + 8V) to (V- -0.5V)
Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1mA
Output Short Circuit Duration (Note 1). . . . . . . . . . . . . . . . Indefinite
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to 125°C
Thermal Resistance (Typical, Note 2) θ
JA
(°C/W) θ
JC
(°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . . 105 N/A
Maximum Junction Temperature (Plastic Package) . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Short circuit may be applied to ground or to either supply.
2. θ
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications Typical Values Intended Only for Design Guidance, V
SUPPLY
= ±10V, T
A
= 25°C
PARAMETER SYMBOL TEST CONDITIONS TYP UNITS
Input Resistance R
I
150 TΩ
Input Capacitance C
I
4.9 pF
Output Resistance R
O
300 Ω
Equivalent Input Noise Voltage e
N
f = 1kHz R
S
= 100Ω 62 nV/√Hz
f = 10kHz 38 nV/√Hz
Short-Circuit Current Source I
OM
+2.6mA
To Opposite Supply Sink I
OM
-2.4mA
Gain Bandwidth Product f
T
0.5 MHz
Slew Rate SR 0.5 V/µs
Transient Response Rise Time t
R
R
L
= 2kΩ, C
L
= 100pF 0.7 µs
Overshoot OS 15 %
Current from Terminal 8 To V- I
8
+20µA
To V+ I
8
-2mA
Electrical Specifications For Equipment Design, At V
SUPPLY
= ±1V, T
A
= 25°C, Unless Otherwise Specified
PARAMETER SYMBOL
TEST
CONDITIONS MIN TYP MAX UNITS
Input Offset Voltage |V
IO
| - 5 10 mV
Input Offset Current (Note 3) |I
IO
| - 0.01 4 pA
Input Current (Note 3) |I
I
|-15pA
Large Signal Voltage Gain A
OL
R
L
= 10kΩ 10 100 - kV/V
80 100 - dB
Common Mode Rejection Ratio CMRR - 560 1800 µV/V
55 65 - dB
Common Mode Input Voltage Range V
lCR
+0.20.5- V
V
lCR
---1.3- V
Power Supply Rejection Ratio PSRR ∆V
IO
/∆V - 100 1000 µV/V
60 80 - dB
Max Output Voltage V
OM
+R
L
= ∞ 0.90 0.95 - V
V
OM
- -0.85 -0.91 - V
Supply Current I+ - 350 650 µA
Device Dissipation P
D
-0.71.1 mW
Input Offset Voltage Temperature Drift ∆V
lO
/∆T- 4-µV/°C
NOTE:
3. The maximum limit represents the levels obtainable on high speed automatic test equipment. Typical values are obtained under laboratory conditions.
CA3420