Use and Care Guide
INSTALLATION HOW TO OPERATE BLUETOOTH SPEAKER:
CONNECTION OPTIONS
SAFETY INFORMATION
PRE-INSTALLATION
IMPORTANT: Read all safety precautions and installations carefully before installing or
servicing this fixture.
• 5.5 ft power cord with plug, link up to 6 shoplight together.
• Do not handle any energized fixture or attempt to energize any fixture with wet hands or while
standing on a wet or damp surface or in water.
• Assure that the fixture is mounted onto a structurally sound surface that will support the
fixture.
• The fixture is designed for use in a 120 VAC, 60Hz fused circuit. Do not use on a dimming
circuit.
• Do not look into the lights.
• Product is intended for use in garages, basements, work areas, utility rooms and recreation
rooms.
• Maximum distance to the receptacle is determined by the length of the cord provided.
(5.5ft, 3-prong, 120V grounded plug included)
• Includes a protective sleeve, such as 0.010-inch (0.25-mm) thick fiberglass, where the path
of cord travel to the ceiling-mounted receptacle is not between the two supporting chains.
• The fixture is intended to be installed directly beneath a ceiling-mounted receptacle. Excess
cord should be secured to one of the supporting chains with a cable tie to keep it out of the
work space.
• Use hook to support chain, not the electrical cord.
• Do not install on radiant-heating type ceiling.
WARNING: Failure to comply with these instructions could result in a potentially fatal electric
shock and/or property damage.
• Carefully remove the fixture from the carton and check to make sure that all hardware is included.
• Be careful not to misplace any of the hardware needed for installing the fixture. If all hardware is
not included, call customer service number.
PLANNING INSTALLATION
HARDWARE INCLUDED
NOTE: The unit is intended to be installed directly beneath a ceiling-mounted receptacle. If
there is excess cord, bind with string or a cable tie to keep it out of work space.
ATTACH THE CEILING HOOKS
ATTACH THE HANGING CHAIN
1. Using hanging chains (Part AA) attach to the “S” hooks (Part BB) previously attached to each side
of the light fixture. (Figure 2)
Attach the center of each hanging chain to the ceiling hooks (Part CC) previously attached.
NOTE: The hanging chain must be bent in half in order to attach each side to an “S” hook.
2.
3. Determine whether a single or multiple units are to be installed. If multiple units will be
installed follow steps in CONNECTION OPTIONS section. Connect lights per instructions and
repeat steps 1-2 (under Attach the Hanging Chain) for each light connected.
4. Plug power cord into an outlet to use pull chain to power on.
AA: 13.4 in. Hanging Chain (2)
Maximum Weight: 7 kgs.
BB: “S” Hook (4)
24 mm x 21 mm x 2 mm
17”
11”
Fold Fold
Fold Fold
ATTACH THE “S” HOOKS
Insert the “S” hooks (Part BB) into each of the holes on both sides of the shop Light.
(Figure 1)
EN | 1 EN | 2 EN | 3
NOTE: A maximum of 6 lights can be connected off of a single circuit.
LINKING CABLE
NOTE: When linking shop lights, you should pair your Bluetooth with the first one in the
linking chain, then connect all linked lights with provided aux cables. Only 1 light will be
able to paired from a single device.
Up to 6 units can be connected using the 5.5 ft power cord. Once installed, plug the power
cord into the end of linked shop light and repeat up to 5 times.
To link the audio in up to 6 shop lights connect the audio cable (Part EE) from the aux out
on first shop light and then into the aux in on second shop light. Repeat for up to 6 lights.
1.
2.
AC Outlet
Connect the power cord
plug to shoplight
AUX IN AUX OUT
Connect ends of audio cable (Part EE) from
Aux Out to Aux In on each linked shoplight
(Figure 2)
65.6ft (20m)
Choose desired location of light fixture making sure it is within reach of an outlet. Use a pencil
to place a mark on the ceiling where each ceiling hook (Part CC) should go. Screw hooks in
place until secure.
CC: Ceiling Hook (2)
3.0 mm x 54.5 mm x 15.6 mm
EE: Audio cable (1)
Length 1.5m
AA
BB
CC
AA
BB
EE
CC
AUX IN
Power Cord Plug
AUX OUT
Reflex Port
Bluetooth Speaker will enter pairing mode when you turn on the light. Activate bluetooth on
your device and find device named BT0450DS0810. Press to pair.
The Bluetooth Speaker will turn off when the light is turned off.
1.
2.
Bluetooth Speaker
AC Outlet
For better operation, the distance between Bluetooth device and the shop light had better less than
65.6 ft (20m) (It depends on the Bluetooth device and the environment).
(Figure 1)
BB
BB
3.51 Ft.