CN4 Mobile Computer CN4, CN4e, CN4N I User’s Manual
Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec Technologies Corporation.
Document Change Record This page records changes to this document. The document was originally released as Revision 001. Version Number Date Description of Change 003 10/2011 Revised to add information on sending feedback about this manual and to correct the clean booting procedure. 002 08/2010 Revised to support the CN4NI Mobile Computer and the EA11 area imager.
iv CN4 Mobile Computer User’s Manual
Contents Contents Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Global Services and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Using the Stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Understanding the Screen Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Aligning the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Configuring the Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Configuring Ethernet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Configuring Bluetooth Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Connecting to a Bluetooth Scanner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Connecting to a Bluetooth Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Connecting to a Bluetooth Audio Device. . . . . . . . . . . . . . . . . . . . . . .
Contents 4 Troubleshooting and Maintaining the CN4 . . . . . . . . . . . . . . . . . . . . . . . . . 87 Calling Product Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Troubleshooting the CN4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Checking 802.11 Network Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin Before You Begin This section provides you with safety information, technical support information, and sources for additional product information. Safety Information Your safety is extremely important. Read and follow all warnings and cautions in this document before handling and operating Intermec equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the safety warnings and cautions.
Before You Begin Web Support Visit the Intermec website at www.intermec.com to download our current manuals (in PDF). Visit the Intermec technical knowledge base (Knowledge Central) at www.intermec.com and click Support > Knowledge Central to review technical information or to request technical support for your Intermec product. Send Feedback Your feedback is crucial to the continual improvement of our documentation.
Before You Begin Who Should Read This Manual This manual is written for the person who is responsible for installing, configuring, and maintaining the CN4, CN4e, and CN4NI Mobile Computers. This manual provides you with information about the features of the mobile computer and how to install, configure, operate, maintain, and troubleshoot it. Before you work with the mobile computer, you should be familiar with your network and general networking terms, such as IP address.
Before You Begin Patent Information Product is covered by one or more of the following patents: 4882476; 4894523; 4953113; 4961043; 4970379; 4988852; 5019699; 5021642; 5038024; 5081343; 5095197; 5144119; 5144121; 5182441; 5187355; 5187356; 5195183; 5216233; 5216550; 5195183; 5195183; 5218191; 5227614; 5233172; 5241488; 5243602; 5258606; 5278487; 5288985; 5308966; 5322991; 5331136; 5331580; 5342210; 5349678; 5359185; 5371858; 5373478; 5389770; 5397885; 5410141; 5414251; 5416463; 5442167; 5464972; 5468947; 5
1 Using the CN4 This chapter introduces the CN4 and CN4e Mobile Computers with Windows® Mobile® 6.1. It also contains hardware and software configuration information to assist you in getting the most out of your computer.
Chapter 1 — Using the CN4 Introducing the CN4 Series Mobile Computers The Intermec CN4 and CN4e Mobile Computers are ergonomically designed mobile computers built on the Microsoft Windows Mobile® 6.1 operating system. They are lightweight, easy-to-use, and run most software developed for the Windows Mobile platform, including standalone, client-server, and browser-based applications. The CN4 and CN4e support similar feature sets.
Chapter 1 — Using the CN4 Standard CN4 features include: • GPS, 802.11b/g, Bluetooth®, and WWAN radios. For WWAN, choose from one of these options: • UMTS/HSDPA • CDMA/1xRTT/EV-DO Rev A • IP64 seal rating and 1.8 m (6 ft) drop specification • a 2-megapixel color camera with LED flash, EA21 Area Imager, or EA11 Area Imager. • 128 MB RAM. • a numeric, QWERTY (CN4), or alphabetic (CN4e) keypad. Use this manual to understand how to use the features and options available on the CN4.
Chapter 1 — Using the CN4 Standard batteries have 8.1 Watt hours capacity and extended batteries have 14.8 Watt hours capacity. You must fully charge the battery before you can use the CN4. The battery used in this device may present a fire or chemical burn hazard if it is mistreated. Do not disassemble it, heat it above 100 °C (212 °F) or incinerate it. If you fail to replace the low battery immediately, you may lose important data or applications.
Chapter 1 — Using the CN4 To change the battery 1 Press and release the Power button to suspend the CN4. 2 Unsnap the top end of the handstrap. 3 Slide the tab on the battery to release it from the CN4. Note: For the CN4NI, use a Phillips screwdriver to loosen and tighten the battery set screw. 4 Place the end of the battery into the battery compartment as shown in the next illustration, and press down on the other end of the battery until it clicks into place. 5 Snap the top of the handstrap into place.
Chapter 1 — Using the CN4 Checking the Battery Status A quick way to check the status of your battery is to look at the battery icon on the CN4 Status bar. Battery Icon Status Icon Status Battery is fully charged. Battery has a medium charge. You should be able to work for several more hours before changing batteries. Battery is low. You need to replace or charge the battery soon. Battery is critically low. You need to replace or charge the battery now. Battery is charging.
Chapter 1 — Using the CN4 Understanding the Battery Status LED (continued) Battery Status Description Steady amber The battery is missing or is unable to charge. If the battery will not charge, it may be because the temperature is outside of the charging range, or you may be using a battery not approved by Intermec. You need to use one of the battery models specified in “Standard and Extended Batteries for CN4 and CN4e” on page 3.
Chapter 1 — Using the CN4 Maximizing Battery Life Batteries are chemical devices. If the batteries are left sitting on a shelf for long periods of time outside the CN4, the batteries slowly discharge, eventually to zero if left uncharged. The battery chemistry resists normal degradation if you store the battery in a charger as opposed to leaving the battery in a discharged state. See the following table for tips you can do to maximize the life of your battery.
Chapter 1 — Using the CN4 There are several ways you can manage power: • You can set the amount of time that the screen stays on, or the amount of time the CN4 stays on after the screen turns off. For help, see “Customizing Power Timeouts” on page 10. • You can change the amount of time the screen backlight stays on. For help, see “Configuring the Backlight” on page 22. • You can choose a Power Management Profile to manage power based on the way you use your CN4.
Chapter 1 — Using the CN4 Power Profiler also provides advanced settings that allow you to finetune the power usage. You can choose to have the Power button turn off the screen or turn off the device. Note: You can also configure all of the settings in Power Profiler using Intermec Settings. For help with Intermec Settings, see “Configuring the CN4 Parameters” on page 48.
Chapter 1 — Using the CN4 To customize power timeout values 1 Tap Start > Settings > System tab > Power Profiler. 2 In the Power Profile tab, tap Enable Advanced Settings. 3 Tap the Screen Settings tab to change screen timeout values: • Check the Enable Screen Off check box to be able to turn off the screen independently of the CN4. • To change the amount of inactivity time before the screen turns off, move the Battery Power or External Power sliders. For battery power, choose from 1 to 6 minutes.
Chapter 1 — Using the CN4 Using the Keypad The CN4 comes with either a QWERTY keypad or a numeric keypad. The CN4e comes with either an alphabetic keypad or a numeric keypad. The QWERTY and alphabetic keypads are for applications that require mainly alphabetic data. The numeric keypads are for applications requiring mainly numeric data. CN4 QWERTY Keypad CN4 Numeric Keypad CN4e Alphabetic Keypad CN4e Numeric Keypad Note: Some available characters are not printed on the keypad overlays.
Chapter 1 — Using the CN4 Using the Color-Coded Keys All keypads include color-coded modifier keys for characters, symbols, and functions printed on the keypad overlay. The numeric keypads include an orange b modifier key and a green c modifier key. The alphanumeric keypads include an orange b modifier key. Using the Color-Coded Keys To Do This Press Example Use an orange character or function printed above a key.
Chapter 1 — Using the CN4 Entering Characters on the Numeric Keypads To type a character or access a function printed in orange on the keypad overlay, press b and then press the key for the character or function you want. To type a character or access a function printed in green on the keypad overlay, press c and then press the key for the character or function you want. Above most of the keys, there is a grouping of three or four letters.
Chapter 1 — Using the CN4 On the CN4 keypads, you can access the Windows Mobile application keys as follows: Windows Mobile Application Keys on CN4 Keypads To Use On Numeric Keypad, Press On QWERTY Keypad, Press Softkey 1 b1 bW Softkey 2 b3 bO “ok” b| bP Using the Power Button When you press the Power ^ button, you put the CN4 into Suspend mode. In this lower power mode, the CN4 continues to supply power to all memory, but turns off power to most hardware such as the display.
Chapter 1 — Using the CN4 Front speaker Microphone Microphone and Front Speaker Locations To adjust the volume of the front speaker 1 Tap the Volume icon ( ) at the top of the screen. 2 In the Volume adjust box, tap On. 3 Move the volume slider for the phone.
Chapter 1 — Using the CN4 Adjusting the Volume of the Rear Speaker The rear speaker is used for all other computer audio. You can set the volume to off, very low, low, medium (default), high, and very high. Rear speaker Volume up/down Location of the Rear Speaker and Volume Control Choose one of these methods to change the rear speaker volume. • Use the Volume slider to change the rear speaker volume: a Tap the Volume icon ( ) at the top of the screen. b In the Volume adjust box, tap On.
Chapter 1 — Using the CN4 Enabling the Vibrate Mode You can enable the vibrate mode when audio is difficult to hear, such as in a high noise environment. When enabled, the CN4 vibrates when the scanner performs a good read or when the phone receives a call. To enable the vibrate feature 1 Tap the Volume icon ( ) at the top of the screen. 2 Tap Vibrate. Note: The Volume icon in the Navigation bar changes to look like a vibrating CN4 ( ) when the Vibrate feature is enabled.
Chapter 1 — Using the CN4 Status bar Today screen Command bar The Windows Mobile Today Screen To turn the screen backlight on and off: • For all keypads except the QWERTY keypad, press b .. • For the QWERTY keypad, press g. Note: To help conserve battery power, you can change the amount of time that the screen backlight stays on. For help, see “Configuring the Backlight” on page 22. Using the Stylus The CN4 has a stylus for selecting items and entering information on the touch screen.
Chapter 1 — Using the CN4 Understanding the Screen Icons The screen icons on the Status bar and Command bar indicate battery charge levels, network connections, and so on. Some standard Microsoft icons are included in this table. Computer Screen Icons Icon Description The battery is full. The battery is low. You need to replace or charge the battery very soon. The CN4 is on external power and the battery is charging. The volume is turned off.
Chapter 1 — Using the CN4 Aligning the Touch Screen If the touch screen does not respond when you tap it with the stylus, you may need to calibrate the screen. To align the touch screen 1 Tap Start > Settings > the Systems tab > Screen. 2 Tap Align Screen and follow the instructions to align the screen. 3 Tap ok. If the touch screen is so out of alignment that you cannot open the Start menu, you may need to align the screen menu using only the keypad, or as a last resort you can perform a clean boot.
Chapter 1 — Using the CN4 Configuring the Backlight By default, the CN4 goes into Screen Off mode when there is no activity on the computer. Screen Off mode turns off the backlight and display. Press a key or tap the screen to resume activity. It is possible to override the backlight settings by changing the power management settings. For more information on configuring power management, see “Managing Power on the CN4” on page 8.
Chapter 1 — Using the CN4 Understanding the Status LEDs The status LEDs above the display show the following information: Good Read LED and Intermec Ready-to-Work indicator Notification LED Battery status LED . Understanding the LEDs LED Color Description Notification Orange The CN4 is notifying you of a pending alarm or message. For more information on the Battery Status LED, see “Understanding the Battery Status LED” on page 6. Good Read Green The CN4 has successfully decoded a bar code.
Chapter 1 — Using the CN4 Using the Imager The CN4 has two available area imagers: EA11 and EA21. The EA11 provides a “laser-like” aimer and is optimized for a scan-intensive environment. The EA21 provides a laser framer and is optimized for document imaging. Both area imagers can scan 1D and 2D bar codes. The following table shows the minimum bar code size supported by each imager.
Chapter 1 — Using the CN4 Reading Bar Codes The CN4 imager can scan 1D and 2D bar code symbologies, composite symbologies, and postal codes. You can position the CN4 in almost any orientation to scan a bar code label.
Chapter 1 — Using the CN4 Imager window Side scan button Front scan buttons CN4e Imager and Scan Button Locations To read bar codes 1 Press the Power button to turn on the CN4, point the scanner window a few inches from the bar code label, and hold steady. 2 Press and hold the Scan button. A laser pointer, illumination beam, and aiming frame turn on.
Chapter 1 — Using the CN4 Laser pointer 3 Center the pointer over the bar code label and move the CN4 so the bar code fills the aiming frame. 4 When a bar code label is successfully read, the CN4 makes a high beep and the Good Read LED lights briefly. 5 Release the Scan button.
Chapter 1 — Using the CN4 If you are using bar code labels that are encoded in a different symbology, you need to enable the symbology on the computer. Use Intermec Settings to enable and disable symbologies. For help, see “Configuring the CN4 Parameters” on page 48. Improving Imager Performance If you experience problems reading bar codes, try some of these tips to improve the imager performance. • Keep your hand as steady as possible while scanning a label.
Chapter 1 — Using the CN4 Capturing Images The Data Collection Resource Kit includes .NET classes you use in your image capture applications. For more information, see “Developing Applications for the CN4” on page 72. The CN4 includes Image Capture, a utility application that demonstrates this feature. Using the Image Capture Application 1 Tap Start > Programs > Image Capture. The Image Capture main screen shows streaming video from the imager.
Chapter 1 — Using the CN4 3 Point the CN4 at the subject for the image and press Enter. The image appears. 4 Tap-and-drag to scroll the image. Tap to zoom in, or tap To save the image, tap to zoom out. . To discard the image, tap . By default, images are saved to the My Documents\ImageCapture directory on the CN4, with the filename Image_$. After you save or discard an image, the main screen appears and the CN4 is ready to capture another image.
Chapter 1 — Using the CN4 Configuring the Image Capture Application The default Image Capture settings apply to most situations where the ambient lighting is adequate for office work. However, you may need to change those settings depending on the conditions in which images will be captured, such as outdoors in bright sunlight or inside a darkened warehouse. To configure Image Capture settings 1 Tap Options and choose Settings. 2 Change settings as needed. For help, see the next table.
Chapter 1 — Using the CN4 Copying Images to Your Desktop PC You can connect to the CN4 with ActiveSync and browse to the \My Documents\ImageCapture directory to download image files to your desktop PC. For help, see “Connecting to a PC” on page 45. You can also use other automated file transfer methods to copy files. Integrating Image Capture Into Your Application You can integrate Image Capture into your own application by calling it from your application.
Chapter 1 — Using the CN4 To use the eMDI application 1 Tap Start > Programs > Document Imaging. 2 Point the CN4 at the document to be captured. 3 Press and hold the Scan button. A laser pointer, illumination beam, and aiming frame turn on.
Chapter 1 — Using the CN4 4 Keep the pointer centered on the document and move the CN4 so the aiming frame approaches the edges of the document. When the frame stops flashing, the CN4 captures the document. 5 Release the Scan button. The captured image appears. 6 Tap-and-drag to scroll the image. Tap to zoom in, or tap to zoom out. To save the image to the Gallery, tap To discard the image and try again, tap . . 7 To close the application, tap ok.
Chapter 1 — Using the CN4 Using the Color Camera Note: The CN4 can be ordered with either a color camera or one of the the area imagers, but not both. The optional, 2-megapixel color camera with flash is factory-installed in the upper back of the CN4, as shown in the following illustration. Flash Camera Color Camera and Flash Location You can take photos in either high-resolution or compressed format, with resolutions up to 1600 x 1200 pixels. When you take a picture, the images are saved as .
Chapter 1 — Using the CN4 After the color camera is enabled, you can configure camera options by going to Menu > Options or Menu > Tools > Options from the Pictures & Video screen. While you are in the Pictures & Videos application, you can select Start > Help for more information on using the camera. To take a picture with the camera 1 Tap Start > Programs > Pictures & Videos. 2 Tap the Camera option in the grid or tap Camera in the taskbar.
Chapter 1 — Using the CN4 Installing a miniSD or SIM Card You can corrupt your miniSD card if you do not follow these installation and removal procedures exactly. Before installing a miniSD card, inspect the gasket in the compartment for any damage or wear, and contact your Intermec representative if you find any damage or wear. The miniSD card and SIM card slots are located below a door inside the CN4 battery compartment.
Chapter 1 — Using the CN4 SIM card SIM card slot miniSD card 5 Close the miniSD/SIM card slot door and insert the two screws. To prevent damage to the door, do not overtighten the screws that secure the card slot door. 6 Replace the battery pack and then press the Power button. The CN4 cold boots.
Chapter 1 — Using the CN4 Setting Up GPS on Your CN4 The integrated Global Positioning System (GPS) receiver in your CN4 delivers standards-based National Marine Electronics Association (NMEA) data strings to GPS applications. However, Intermec recommends that you use the GPS Intermediate Driver (GPSID) instead of directly accessing the GPS hardware. The GPSID is a Microsoft software component that interacts between applications and the GPS hardware.
Chapter 1 — Using the CN4 2 Tap External GPS. The GPS Settings screen appears. 3 On the Programs tab, select the COM port that you want your programs to use to get GPS data from your CN4. Note: COM1 and COM3 are reserved. 4 Tap the Hardware tab, and select these settings.
Chapter 1 — Using the CN4 5 Tap the Access tab and select the Manage GPS automatically check box. 6 Tap ok. To enable extended ephemeris 1 Tap Start > Settings > the System tab. 2 Tap iGPS settings. The iGPS Settings screen appears. 3 Tap the Advanced tab. 4 Select the Enable extended ephemeris check box. 5 Tap ok.
Chapter 1 — Using the CN4 Learning About Additional GPS Options for the CN4 Intermec provides enhanced feature support for the Extended Ephemeris data capability. For the latest Extended Ephemeris data files and other CN4 downloads, visit the CN4 downloads page on the Intermec website at www.intermec.com. For more information about programming for Extended Ephemeris GPS, visit the Intermec Developer Library at www.intermec.com/idl.
2 Connecting and Configuring the CN4 Use this chapter to understand how to configure the CN4 to communicate in your network.
Chapter 2 — Connecting and Configuring the CN4 Managing the CN4 With SmartSystems Foundation Intermec's SmartSystems™ Foundation is a software platform that lets you manage all of your SmartSystems-enabled devices, including the CN4, simultaneously from a central server. The SmartSystems console displays all SmartSystems-enabled computers and peripherals in your network.
Chapter 2 — Connecting and Configuring the CN4 With an AutoDeploy license, SmartSystems can automatically push software, configuration settings, and other files to connected CN4s. The license also enables Scan-to-Connect, which makes connecting additional CN4s to your wireless network as easy as reading bar codes. SmartSystems Foundation can be downloaded at no charge from the Intermec website. For more information, visit www.intermec.com\SmartSystems.
Chapter 2 — Connecting and Configuring the CN4 Configuring the Phone The CN4 supports two types of cellular phone technology: • CDMA EV-DO Rev A • UMTS and GSM/EDGE With the radio module installed in the CN4, you can send and receive telephone calls as well as transmit data through wide-area (WAN) cellular networks. The CN4 provides a phone speaker, microphone, and speakerphone. It also supports Bluetooth headsets or hands-free kits. By default the phone is enabled.
Chapter 2 — Connecting and Configuring the CN4 After you supply the ESN to your carrier, they will respond with values that you must enter using the Windows Mobile Activation Wizard (if required). Some of the supported carriers do not require you to enter any values. The following table shows the carriers, the correct activation method to use, and the values that you need to activate your phone.
Chapter 2 — Connecting and Configuring the CN4 Activating the GSM/EDGE Phone You use a SIM card to activate the GSM/EDGE phone on the CN4. You can purchase the SIM card from your network provider. To activate the GSM/EDGE phone • Install the SIM card in the CN4. For help, see “Installing a miniSD or SIM Card” on page 37. You may need to configure network settings for your provider. For information, tap Start > Help and see the procedures in the Windows Mobile online Help.
Chapter 2 — Connecting and Configuring the CN4 computers and peripherals. For more information, see the next section. • Directly on the CN4. Using Intermec Settings on the CN4 changes only the settings on that computer. For more information, see “Using Intermec Settings Directly On the CN4” on page 50. • You can use a third-party device management product that includes Intermec Settings Configuration Support, such as the Microsoft System Center Mobile Device Manager. Visit http://www.microsoft.
Chapter 2 — Connecting and Configuring the CN4 2 Select Intermec Settings. 3 Change settings as needed. As you choose parameters, information on each parameter appears in the upper right-hand pane of the Intermec Settings browser. 4 When you are done making changes, choose File > Save Settings. For help with using Intermec Settings, in the browser click Help > Contents. For information on all parameters in Intermec Settings, see the Intermec Settings Command Reference Manual.
Chapter 2 — Connecting and Configuring the CN4 To use Intermec Settings 1 On the CN4, tap Start > Settings > the System tab > Intermec Settings. 2 Tap a menu bar. A new menu or a list of configurable items appears. 3 In a list of configurable items, choose or change options by entering data in the entry fields or checking the appropriate check box. • To restore the default settings to all items in the current menu, tap Menu > Restore Menu Defaults.
Chapter 2 — Connecting and Configuring the CN4 Hiding Menu Items in Intermec Settings In Intermec Settings, you can hide items in the CN4 menus, or in the directory tree in the SmartSystems console. Hidden items are not saved when you back up your settings in the SmartSystems console. In Intermec Settings in the SmartSystems console: • To hide menu items, right-click a menu item and choose Hide Menu Item from the popup list. Click Yes to clear the confirming message.
Chapter 2 — Connecting and Configuring the CN4 Configuring 802.11b/g Radio Communications Make sure all components with antennas are at least 30 cm (1 ft) apart when power is applied. Failure to comply could result in equipment damage. Your CN4 has an 802.11b/g radio to transfer data using wireless communications and supports the TCP/IP network protocols. This section of the manual assumes that your wireless network is set up, including your access points.
Chapter 2 — Connecting and Configuring the CN4 b Subnet mask c Default router 3 If necessary, set these parameters: • Primary and secondary DNS servers • Primary and secondary WINS servers 4 Make sure that your CN4 is communicating with the network and that the network can see your CN4. For more information, see “Managing Network Connections With iConnect” on page 58.
Chapter 2 — Connecting and Configuring the CN4 Connecting to a Bluetooth Scanner You can connect to an Intermec Bluetooth scanner, such as the SF51 or SR61, by using the Wireless Scanning enabler. To use the Wireless Scanning enabler 1 Tap Start > Settings > the System tab > Wireless Scanning. 2 Tap Add Device. 3 To add a scanner by scanning a bar code on the CN4: a Tap Quick Connect and then tap Next. b Scan the bar code with the scanner and then tap Finish.
Chapter 2 — Connecting and Configuring the CN4 Connecting to a Bluetooth Printer 1 Choose Start > Settings > the System tab > Wireless Printing. 2 To search for printers: a Tap Search. The CN4 looks for printers, and the Bluetooth device names and addresses of found printers appear in the list. b Tap a printer device name in the list to select it, and then tap Set. To manually add a printer: • Tap Manual, enter the Bluetooth device address for the printer in the entry field, and then tap Set.
Chapter 2 — Connecting and Configuring the CN4 Connecting to a Bluetooth Audio Device Use the Bluetooth Audio enabler to discover, activate, and connect to Bluetooth audio devices such as a headset. This enables system sounds to be monitored through the headset. To connect to a Bluetooth audio device 1 Select Start > Settings > the System tab > Bluetooth Audio. The Bluetooth Audio screen appears. 2 Follow the onscreen instructions to connect to a Bluetooth audio device.
Chapter 2 — Connecting and Configuring the CN4 Managing Network Connections With iConnect After you configure 802.11 or Ethernet network settings, you can use the iConnect utility to: • check the network connection status with a ping test. • change basic network parameters. • change Funk security profile settings. • turn the 802.11 radio, Ethernet, phone, or Bluetooth radio on and off. To turn a network connection on or off 1 Tap the iConnect icon ( screen.
Chapter 2 — Connecting and Configuring the CN4 3 Choose Ethernet or Wireless from the connection type list. 4 Choose Ping my gateway or DHCP server if you are using DHCP. Or, choose Ping the host address below and enter the host address in the entry field. 5 Tap Ping. The ping test runs and checks your connection. If the connection is OK, “Connection Validated” appears. To check overall connection status 1 Tap the iConnect icon ( screen.
Chapter 2 — Connecting and Configuring the CN4 This section explains how to configure wireless security on your CN4. If you choose not to use security, see “Disabling Security” on page 70. Intermec recommends that you always implement security. You must use either Funk or Microsoft security to implement your security solution. For details, see the next section, “Choosing Between Microsoft and Funk Security.” If you are using WPA-802.1x, WPA2-802.1x, or 802.
Chapter 2 — Connecting and Configuring the CN4 Selecting a Funk Security Profile You can define up to four profiles for Funk security. Different profiles let your CN4 communicate in different networks without having to change all of your security settings. For example, you may want to set up one profile for the manufacturing floor and one for the warehouse. By default, the active profile is Profile 1. Note: You can also use the Profile Wizard to configure most wireless security settings.
Chapter 2 — Connecting and Configuring the CN4 7 For 8021x, choose TTLS, PEAP, EAP-FAST, or TLS. 8 If you choose TTLS or PEAP: a For Prompt for Credentials, choose Enter credentials now. Note: You can use Prompt for Credentials to troubleshoot your network connection. b Enter a User Name and User Password. c For Validate Server Certificate, choose Yes. Note: The correct date must be set on your CN4 when you enable Validate Server Certificate.
Chapter 2 — Connecting and Configuring the CN4 8 For Pre-Shared Key, enter the pre-shared key or passphrase. The pre-shared key must be a value of 32 hex pairs preceded by 0x for a total of 66 characters. The value must match the key value on the access point. The passphrase must be from 8 to 63 characters. After you enter a passphrase, the CN4 internally converts it to a pre-shared key. This value must match the passphrase on the authenticator. 9 Save your settings. Configuring 802.
Chapter 2 — Connecting and Configuring the CN4 d (Optional) To increase your level of security, enter a Server 1 Common name and a Server 2 Common name. 10 Save your settings. Configuring LEAP Security 1 Make sure the communications and radio parameters on your CN4 are configured. 2 Make sure Funk is selected as your security choice. 3 Start Intermec Settings. 4 Choose Communications > 802.11 Radio > Funk Security. 5 Select the profile you want to configure. 6 For 8021x, choose LEAP.
Chapter 2 — Connecting and Configuring the CN4 Enter an ASCII key or a hex key that is either 5 bytes or 13 bytes long depending on the capability of the radio. Set a 5- byte value for 64-bit WEP or a 13-byte value for 128-bit WEP. Hex keys must be preceded by 0x and contain 5 or 13 hex pairs. 10 For Transmit key, choose the key you want to use for transmitting data. 11 Save your settings. Selecting Microsoft as Your Security Choice The default security setting is Funk.
Chapter 2 — Connecting and Configuring the CN4 3 Choose Communications > 802.11 Radio > Microsoft Security. 4 For Infrastructure Mode, choose Infrastructure. 5 For Network Authentication, choose WPA. Data Encryption automatically defaults to TKIP. 6 For 802.1x Authentication, choose either MD5, TLS, or PEAP. 7 If you choose TLS: a Choose Properties > Run App. The Auth. Settings dialog box appears. b Choose Select. c Select your certificate from the list and press Enter. The User Logon dialog box appears.
Chapter 2 — Connecting and Configuring the CN4 The pre-shared key must be a value of 32 hex pairs preceded by 0x for a total of 66 characters. The value must match the key value on the authenticator. The passphrase must be from 8 to 63 characters. After you enter a passphrase, the CN4 internally converts it to a pre-shared key. This value must match the passphrase on the authenticator. 7 Save your settings. Configuring 802.
Chapter 2 — Connecting and Configuring the CN4 9 For Network Key Setting, choose Automatic. 10 Save your settings. Configuring Static WEP Security With Microsoft Security 1 Make sure the communications and radio parameters on your CN4 are configured. 2 Start Intermec Settings. 3 Choose Communications > 802.11 Radio > Microsoft Security. 4 For Network Authentication, choose Open. 5 For Data Encryption, choose WEP. 6 For Network Key Setting, choose Enter Key and Index.
Chapter 2 — Connecting and Configuring the CN4 3 Tap Edit Selected Profile > the Security tab > Get Certificates. Note: PFX encoded certificates are also supported. Tap the Import pfx button to import a PFX encoded certificate. 4 To import a root certificate: a Tap the <<< button next to the Import Root Certificate field to select the root certificate (DER-encoded .cer file) to import. b Click Import Root Cert to install the selected certificate.
Chapter 2 — Connecting and Configuring the CN4 d Tap OK. The Enrollment Tool message box appears telling you that the certificate has been added. e Tap OK to close the message box. Disabling Security If you choose not to use security with your wireless network, you can disable it on the CN4. Intermec recommends that you always set security in your network. To disable security 1 Start Intermec Settings. For help, see “Configuring the CN4 Parameters” on page 48. 2 Choose Communications > 802.
3 Developing and Installing Applications Use this chapter to understand the guidelines for developing applications and installing them on the CN4.
Chapter 3 — Developing and Installing Applications Developing Applications for the CN4 Use the Intermec Resource Kits to develop applications to run on the CN4. The Resource Kits are a library of C++, .NET, Java, and web components grouped by functionality that you can use to create applications for the computer. The Resource Kits are part of the Intermec Developer Library (IDL), and can be downloaded from the Intermec website at www.intermec.com/idl.
Chapter 3 — Developing and Installing Applications If you need to cold boot the CN4, files copied to any of these locations are safe as long as the AutoRun system is installed in the appropriate location. When AutoRun is installed on the CN4, all .cab files in the CabFiles folder are automatically extracted after a cold boot. For more information about AutoRun, see the Intermec Developer Library Resource Kit Developer’s Guide.
Chapter 3 — Developing and Installing Applications 2 Double-click the application file to install it. The application file should appear in the Software Vault. 3 From the SmartSystems console in the Software Vault, drag-anddrop the application onto each CN4 in your network, or drop the application on a group of CN4s contained in a folder. You can also use SmartSystems Scan-to-Connect to connect the CN4 to your network and install software.
Chapter 3 — Developing and Installing Applications Installing Applications Using the FTP Server The CN4 has a built-in FTP server that connects to a network through Ethernet, 802.11 b/g, or WAN (Wireless Access Network). You can use the server to transfer your application file to the computer. Because you can create FTP scripts to automate the process of copying files to the computer, this option is useful when you need to send files to a large number of computers.
Chapter 3 — Developing and Installing Applications To create and install the AutoRun.dat file on your computer 1 Create a folder called System on your CN4. 2 Open the Notepad application on your PC. 3 Write commands for AutoRun.dat using the supported AutoRun script commands. 4 Save the Notepad file as AutoRun.dat. 5 Copy the AutoRun.dat file to the System folder on the CN4. During every boot, the system scans for AutoRun.dat in the System folder. AutoRun supports the following script commands in AutoRun.
Chapter 3 — Developing and Installing Applications • Path to and name of the Image Capture application. Default is “\\Program Files\\Intermec\\ImageCapture\\ImageCapture.exe”. • Path to and name of the .xml configuration file that Image Capture should use when called by your application. This way you can use a custom .xml configuration file based on your needs. If no .xml file is specified, Image Capture uses its default settings, or looks for an .xml file in its local directory.
Chapter 3 — Developing and Installing Applications Field Definitions for ImageCapture_Config.xml (continued) Field Name Valid Values Description True or false Default is true. When set to false, user cannot change settings in the Conditioning tab. allowChanges True or false Default is true. When set to false, user cannot change the edge enhancement setting. edgeEnhancement None, low, medium, Default is None. If no value is provided, the edge or high enhancement value is unchanged.
Chapter 3 — Developing and Installing Applications Field Definitions for ImageCapture_Config.xml (continued) Field Name Valid Values Description allowChanges True or false Default is false. If set to true, user can change the directory where saved images are stored. imageLocation File path Default is no value. If no value is provided, the application does not change the directory where saved images are stored (My Documents\ ImageCapture). allowChanges True or false Default is false.
Chapter 3 — Developing and Installing Applications Image Capture XML Example This XML demonstrates how to use the fields as defined in the previous section. PAGE 93Chapter 3 — Developing and Installing Applications To free up virtual memory 1 Go to Start > Programs > File Explorer. 2 Browse to the Windows folder and scroll down to find InstallSelect. 3 Tap InstallSelect. A Caution message appears, reminding you that removing files may reduce functionality. 4 Tap OK to clear the message. The InstallSelect screen appears. 5 Clear the check box for each component you do not want installed after a clean boot. For a description of each component, see the next table.
Chapter 3 — Developing and Installing Applications InstallSelect Software Components (continued) Component Name Description Printer Support Provides Intermec printer driver support. Intermec DHCP Client Provides the Intermec DHCP client application. Printer_Configlet Intermec Settings configuration support for Bluetooth printers. Bluetooth Intermec Bluetooth integration support. IDLRuntime Runtime files supporting the Data Collection and Device Resource Kits.
Chapter 3 — Developing and Installing Applications There are two ways to upgrade your computer: • You can upgrade your computer using the SmartSystems console. For help, see “Upgrading the CN4 Using SmartSystems Foundation” on page 84. • You can upgrade your computer using a storage card. For help, see “Upgrading the CN4 Using a miniSD Card” on page 85. Locating Upgrade Files Before you can upgrade, you need to download the latest upgrade files from the Intermec website to your desktop PC.
Chapter 3 — Developing and Installing Applications Upgrading the CN4 Using SmartSystems Foundation You can use the SmartSystems Foundation console to upgrade the operating system on your CN4. For information on using SmartSystems Foundation, see “Managing the CN4 With SmartSystems Foundation” on page 44. To upgrade the CN4 using SmartSystems Foundation 1 On your desktop PC, open the SmartSystems console. 2 Make sure the SmartSystems console and the CN4 are on the same subnet.
Chapter 3 — Developing and Installing Applications Upgrading the CN4 Using a miniSD Card To use a miniSD card to upgrade the computer, you need an SD card reader and a miniSD adapter card formatted as FAT16. To upgrade the operating system using a miniSD card 1 Copy all required OS upgrade files to the miniSD card. 2 Insert the miniSD card into the CN4. For help, see “Installing a miniSD or SIM Card” on page 37.
Chapter 3 — Developing and Installing Applications 86 CN4 Mobile Computer User’s Manual
4 Troubleshooting and Maintaining the CN4 If you encounter any problems while using the CN4, look in this chapter to find a possible solution. You will also find information on routine maintenance.
Chapter 4 — Troubleshooting and Maintaining the CN4 Calling Product Support If you cannot find the answer to your problem in the Troubleshooting the CN4 section, you can visit the Intermec technical knowledge base (Knowledge Central) at intermec.custhelp.com to review technical information or to request technical support. If you still need help after visiting Knowledge Central, you may need to call Product Support.
Chapter 4 — Troubleshooting and Maintaining the CN4 To find your operating system version 1 Tap Start > Internet Explorer. 2 Tap the Intermec logo. The Intermec page appears and displays the software build information. Troubleshooting the CN4 If you send the CN4 in for service, it is your responsibility to save the computer data and configuration. Intermec is responsible only for ensuring that the hardware matches the original configuration when repairing or replacing the computer.
Chapter 4 — Troubleshooting and Maintaining the CN4 Problems While Operating the CN4 Problem Solution You press the Power button and nothing happens. • Make sure the backlight is on. • Make sure you have a charged battery that is installed correctly. For help, see “Charging the Battery” on page 4. • Replace the battery with a charged battery. For help, see “Changing the Battery” on page 4. • Perform a warm boot or a cold boot. For help, see “Resetting the CN4” on page 97. The Battery status LED is on.
Chapter 4 — Troubleshooting and Maintaining the CN4 Problems With 802.11 Network Connectivity (continued) Problem Solution The CN4 is connected to the network and you move to a new site to collect data. Your CN4 now shows you are not connected to the network. Move closer to an access point or to a different location to reestablish communications until you reconnect with the network. Any data collected while out of range is transmitted over the network.
Chapter 4 — Troubleshooting and Maintaining the CN4 Problems While Configuring 802.1x Security (continued) Problem Solution The CN4 indicates it is not authenticated. Make sure that: • the User Name and Password parameters on the CN4 must match the user name and password on authentication server. You may need to reenter the password on both the CN4, authentication server. • on your authentication server, the user and group are allowed and the group policy is allowed to log into the server.
Chapter 4 — Troubleshooting and Maintaining the CN4 Problems Reading Bar Codes (continued) Problem Solution When you release a Scan button or handle trigger, the Good Read light does not turn off. The Good Read light will remain on if you configure the computer to use continuous/edge triggering. If you configure the computer for level triggering and the Good Read light remains on, there may be a problem. Press one of the Scan buttons or pull the trigger again without scanning a bar code label.
Chapter 4 — Troubleshooting and Maintaining the CN4 Checking 802.11 Network Status If you have trouble connecting to your 802.11 wireless network: • Make sure you have correctly set network parameters on the CN4. • Check your wireless security settings. Follow the next procedure to use iConnect to verify available access points and networks, check signal strength, and view other diagnostics.
Chapter 4 — Troubleshooting and Maintaining the CN4 4 Tap the Scan tab to view a list of available 802.11 networks. The list includes the signal strength, channel, and MAC address for each network. • Tap Scan to refresh the screen. 5 Tap the Supp tab to view radio supplicant information, including a list of supplicant events and authentication status. • To verify the settings for the currently active security profile, tap Configure Profile. The Profile Wizard for the active profile appears.
Chapter 4 — Troubleshooting and Maintaining the CN4 6 Tap the Ping tab to run a ping test to the host. To run a ping test: a In the Host field, enter the IP address of the host. b From the Repetitions list, choose the number of times the CN4 will ping the host. c Tap Ping. The graph shows the amount of time it takes for the host to return the ping. Tap List to see this information in a list format. 7 Tap the RSSI tab to view the received signal strength of the host signal.
Chapter 4 — Troubleshooting and Maintaining the CN4 • Tap Mark to place an arrow marker above the graph. 8 Tap the Conf tab to set up a log file that lists RSSI history. This screen includes the 802.11 radio driver version and available radio modes. To create a log file: a Check the Log to File check box. b (Optional) Change the sample period and number of samples displayed. c Tap Log File. The Save As screen appears.
Chapter 4 — Troubleshooting and Maintaining the CN4 • Clean booting the CN4 Warm Booting the CN4 You may need to perform a warm boot to correct conditions where an application stops responding to the system. To warm boot the computer • Press and hold the Power button for 10 seconds. Or, • Right-click on the CN4 via the SmartSystems console and select Intermec Power Tools > Warm Boot Device. The computer systematically shuts down, restarts, and goes through the initialization process.
Chapter 4 — Troubleshooting and Maintaining the CN4 Reset button Locating the Reset Button on the CN4 Clean Booting the CN4 A clean boot erases the memory in the mobile computer, including all applications and data files found in the ObjectStore, and loads only the default files and programs required by the CN4 operating system. During a clean boot, the CN4 first looks for the SSPB files on an installed miniSD card. If no card is found, the CN4 loads the SSPB files in the Flash File Store.
Chapter 4 — Troubleshooting and Maintaining the CN4 4 Insert the battery pack into the CN4, and immediately press and hold the Power button and both buttons on the left side. 5 Continue to hold the Power button and both buttons on the left side until a Warning message appears on the display. 6 Release the Power button and both buttons on the left side, read the message, and press either button on the right side to continue. 7 Wait for the CN4 to load files from its ROM.
A Specifications and Default Settings 101
Appendix A — Specifications and Default Settings Physical and Environmental Specifications CN4 Physical Dimensions (excluding overmold) Length:17.3 cm (6.8 in) Width: 8.1 cm (3.2 in) Height: 2.8 cm (1.1 in) with standard battery 3.3 cm (1.3 in) with extended battery Weight: 397 to 454 g standard battery (14 to 16 oz) CN4e Physical Dimensions (excluding overmold) Length: 21.0 cm (8.3 in) Width: 8.1 cm (3.2 in) Height: 3.3 cm (1.
Appendix A — Specifications and Default Settings Touch Screen Specifications Transflective TFT; QVGA color with touch panel; 240 x 320 pixels; 8.9 cm (3.5 in) diagonal active area; 5-level LED backlight control with settings Electrical Specifications External charge power: 5 V +/- 5% @3.
Appendix A — Specifications and Default Settings Regulatory Approvals Safety: cULus Listed, GS, CCC, GOST (pending), NOM, HKSI EMC: FCC Part 15B – Class B, ICES-003 Class B, EN 55022 Class B, EN 55024, EN 301 489-17, AS/ZNS 3548, GB9254-1998, BSMI, ICASA Radio: FCC Part 15.247, Industry Canada RSS 210, EN 300 328-2, Telecom. Num.
Appendix A — Specifications and Default Settings EA21 Area Imager Typical Reading Distances Typical distances are measured in an office environment (250 lux). 0" 4" 8" 12" 16" 20" 24" 28" 32" in 16" 40 Note: Minimum distances depend on bar code length. 12" 30 PDF417 10 mils 8" 20 Data Matrix 10 mils 4" 10 0" 0 4" 10 0.15mm/6 mils 8" 20 0.25 mm / 10 mils 12" 30 100% contrast UPC EAN 16" 40 0.
Appendix A — Specifications and Default Settings EA21 Area Imager Minimum Reading Distances Minimum distances are measured in the dark (0 lux). 0" 4" 8" 12" 16" 20" 24" 28" 32" in 16" 40 Note: Minimum distances depend on bar code length. 12" 30 PDF417 10 mils 8" 20 Data Matrix 10 mils 4" 10 0" 0 4" 10 0.15mm/6 mils 8" 20 0.25 mm / 10 mils 12" 30 100% contrast UPC EAN 16" 40 0.
Appendix A — Specifications and Default Settings EA11 Area Imager Typical Reading Distances 0" 4" 8" 12" 16" 20" in 10" 25 8" 20 Data Matrix 7.5 mils 6" 15 4" 10 PDF417 6.6 mils 2" 5 0" 0 2" 5 4" 10 0.125mm/5mils 6" 15 0.25 mm / 10 mils 8" 20 100% contrast UPC EAN 10" 25 0.5 mm / 20 mils cm 0 10 20 30 40 50 EA11 Typical Reading Distances Symbology Density Minimum Distance Maximum Distance Code 39 0.125 mm (5 mil) 0.20 mm (8 mil) 0.25 mm (10 mil) 0.
Appendix A — Specifications and Default Settings EA11 Area Imager Minimum Reading Distances Minimum distances are measured in the dark (0 lux). 0" 4" 8" 12" 16" in 10" 25 8" 20 Data Matrix 7.5 mils 6" 15 PDF417 6.6 mils 4" 10 2" 5 0" 0 2" 5 4" 10 0.125mm / 5mils 6" 15 0.25 mm / 10 mils 20 8" 100% contrast UPC EAN 10" 25 0.5 mm / 20 mils cm * 0 10 20 30 40 50 EA11 Minimum Reading Distances Symbology Density Minimum Distance Maximum Distance Code 39 0.
Appendix A — Specifications and Default Settings Accessories All of the accessories listed below work for both the CN4 and CN4e models unless otherwise noted. AA15 Audio Adapter Use the audio adapter to connect your audio headset to the CN4. AA16 Ethernet Adapter Use the Ethernet adapter to connect the CN4 to your Ethernet network without using a dock. AA17 RS-232/DEX Adapter Use the RS-232/DEX adapter to enable the CN4 to receive serial communications.
Appendix A — Specifications and Default Settings AR1 Magnetic Card Reader The magnetic card reader provides magnetic stripe reading capability to the CN4. AV6 Vehicle Dock Use the vehicle dock to hold and charge the CN4 while using it on a vehicle. AV9 Vehicle Dock Use the vehicle dock to hold and charge the CN4e while using it on a vehicle. CN4 Scan Handle Use the scan handle to provide better ergonomics for higher-volume scanning applications.
Appendix A — Specifications and Default Settings Symbology (continued) Default Value ChinaPost Disable Codabar Disable Codablock A Disable Codablock F Disable Code 11 Disable Code 39 Enable Code 93 Disable Code 128/GS1-128 Enable DataMatrix Enable DutchPost Disable EAN/UPC Enable UPC A, UPC E, EAN 8, EAN 13 EAN.
Appendix A — Specifications and Default Settings 112 Symbology Option Default Value Preamble None (disabled) Postamble None (disabled) Global Symbology ID Disable Scanner Setting Default Value Hardware Trigger Enable Turn Off After Good Read Enable/One-shot Trigger mode (area imagers only) Level Imager Setting Default Value Predefined Modes 1D and 2D Standard Sticky aimer LED duration 0 (disabled) Signature Image Capture Disable Decode Security Setting Default Value Consecutive D
Appendix A — Specifications and Default Settings Communications Communication Setting Default Value Security Choice Funk Allow Security Changes Enabled Active Profile Profile 1 DHCP Enabled Import Root Certificates False Import User Certificates False Import Pac Files False Radio Measurement 250 Radio Enabled Ethernet Adapter IP Settings DHCP Bluetooth Power Off Bluetooth Discoverable Disabled Bluetooth Connectable Enabled Device Settings Device Settings Default Value Adjust f
Appendix A — Specifications and Default Settings 114 Device Settings (continued) Default Value Scan Button Remapping (middle scan button) Scanner Power Profiles Standard Power Button Off when pressed Device Off (battery power) 2 minutes Display Off (battery power) 1 minute Device Off (external power) Disabled Display Off (external power) Disabled CN4 Mobile Computer User’s Manual
Appendix A — Specifications and Default Settings GPS Setting Default Value Extended Ephemeris Data Disable Download Interval Disable Download Interval Start Time 1:00 AM Download Interval Stop Time 3:00 AM Push Interval Disable Push Interval Start Time 1:00 AM Push Interval Stop Time 3:00 AM Poll Period Disable Position Change 50 meters Fix Interval 0 WAAS Disable Baud Rate 33600 Device Monitor Setting Default Value Poll Period 1 minute Backup Battery Charge Remaining 10 Sto
Appendix A — Specifications and Default Settings 116 CN4 Mobile Computer User’s Manual
B Keypads and Keystrokes 117
Appendix B — Keypads and Keystrokes Standard Characters Use the following tables to learn how to enter standard and other available characters and functions with the keypad. If there is no sequence of keystrokes for a particular character or function, it is only available through the soft input panel (SIP), which can be accessed by tapping the keyboard icon on the touch screen.
Appendix B — Keypads and Keystrokes Alphanumeric Characters (continued) Character Numeric Keypad QWERTY Keypad Alphabetic Keypad q c77 c777 c7777 c8 c88 c888 c9 c99 c999 c9999 c12 c122 c1222 c13 c133 c1333 c14 c144 c1444 c15 Q R S T U V W X Y Z ]A ]B ]C ]D ]E ]F ]G ]H ]I ]J Q R S T U V W X Y Z ]A ]B ]C ]D ]E ]F ]G ]H ]I ]J r s t u v w x y z A B C D E F G H I J CN4 Mobile Computer User’s Manual 119
Appendix B — Keypads and Keystrokes Alphanumeric Characters (continued) Character Numeric Keypad QWERTY Keypad Alphabetic Keypad K c155 c1555 c16 c166 c1666 c17 c177 c1777 c17777 c18 c188 c1888 c19 c199 c1999 c19999 0 1 2 3 ]K ]L ]M ]N ]O ]P ]Q ]R ]S ]T ]U ]V ]W ]X ]Y ]Z bg bY bU bI ]K ]L ]M ]N ]O ]P ]Q ]R ]S ]T ]U ]V ]W ]X ]Y ]Z bg bJ bK bL L M N O P Q R S T U V W X Y Z 0 1 2 3 120 CN4 Mobile Computer User’s Manual
Appendix B — Keypads and Keystrokes Alphanumeric Characters (continued) Character Numeric Keypad QWERTY Keypad Alphabetic Keypad 4 4 5 6 7 8 9 bH bJ bK bB bN bM bP bQ bR bV bW bX 5 6 7 8 9 Other Available Characters The next table lists both characters printed on the keypad overlays and hidden characters not printed on the overlays.
Appendix B — Keypads and Keystrokes Other Available Characters and Functions (continued) To Enter Numeric Keypad QWERTY Keypad Alphabetic Keypad > (greater than) N/A - (hyphen) b* ( (left parentheses) N/A < (less than) N/A % (percent) N/A . (period) . b# ]b. bG ]b9 ]bX bR . bT bV bA ]bg bZ ]bG bj b] e bO bP ] bW s ]. ]U ]bX ]bT ]bC .
Appendix B — Keypads and Keystrokes Characters not available from the keypads are: • Left and right bracket ([ or ]) • Left and right curly bracket ({ or }) • Semicolon (;) • Tilde (~) Use the SIP to enter these characters. Language-Specific Characters The next table lists the available language-specific characters, such as those using diacritical marks.
Appendix B — Keypads and Keystrokes 4 Press b to unlock the orange key.
I Index 125
Index Numerics 802.
Index Bluetooth (continued) printer, connecting to 56 QD ID 102 scanner, connecting to 55 Wireless Printing enabler 56 Wireless Scanning enabler 55 Bluetooth Audio enabler 57 booting the CN4 97 clean 99 cold 98 warm 98 button, power 15 C calibrating screen 21 calling product support 88 camera 35 cleaning window 100 configuring 36 capacitor, super, as backup power 4 card, miniSD, using to install applications 74 carriers, supported 46 CDMA activation values table 47 carriers, supported 46 MSID 47 MSL 47 phon
Index cold boot, performing 98 color-coded keys 13 communications 802.11, configuring 53 available protocols 102 Bluetooth, configuring 54–57 configuring CN4 for network 52 default settings 113 Ethernet, configuring 53 phone, activating 46 security, wireless 59 serial 57 troubleshooting wireless network 94 USB 57 configuration commands, troubleshooting 89 configuration number, finding 88 configuring the CN4 48 802.
Index G Good Read LED described 23 troubleshooting 93 GPS configuring 39 default settings 115 extended ephemeris 39, 41 GPSID, overview 39 green battery LED, described 6 green key, using 13 green status LED, described 23 GSM/EDGE activation 48 H hardware specifications 102 humidity specification 103 I iConnect application described 58 enabling FTP server 75 icons battery 6 understanding 20 IDL (Intermec Developer Library) 72 iGPS settings 41 Image Capture application 29 using in your application 76 XML exam
Index Master Subsidy Lock (MSL) 47 memory 102 freeing up virtual for applications 80 installing applications in 72 microprocessor 102 Microsoft security 802.1x 67 choosing 65 static WEP 68 when to use 60 WPA 65 WPA-802.
Index R radio certifications 103 power output 103 radios 802.
Index touch screen, aligning 21 troubleshooting 89–93 802.11 connectivity 90 802.11 network status 94 802.
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2011 Intermec Technologies Corporation. All rights reserved.
