Quick Start Guide Model 730 Mobile Computer
Thank you for purchasing the Intermec Model 730 Color Mobile Computer with Microsoft Windows Mobile 2003. You will find your Model 730 useful in a variety of applications. Its integrated peripherals and rugged design ensure reliable service for years to come. This guide provides information needed to get started using your Model 730.
Contents Model 730 Color Mobile Computer Description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setting Up Your Model 730 . . . . . . . . . . . . . . . 6 Learning About The Keypad . . . . . . . . . . . . . . . Gold Plane Keys . . . . . . . . . . . . . . . . . Alpha (Blue) Plane Keys-Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . Linear Imager/Keypad Shift and Notification LED . . . . . . . . . . . . . Action and Up/Down Navigational Buttons . . . . . . . . . . . . . . . . . . . . .
Case and Display . . . . . . . . . . . . . . . 19 Where to Find More Information . . . . . . . . . . 20 End User License Agreement . . . . . . . . . . . . . 20 Microsoft Windows Mobile 2003 Software for Pocket PC . . . . . . . . . . . 20 Intermec Technologies Corporation End User License Agreement . . . . . . . . . . . . . . . . . . . 24 Global Services and Support . . . . . . . . . . . . . . 25 Warranty Information . . . . . . . . . . . 25 Web Support . . . . . . . . . . . . . . . . . .
Model 730 Color Mobile Computer Description Navigational key Imager/ Alpha LED Power Status LED Backlight (Gold + 3) ON/OFF Gold plane key Alpha (Blue) plane key Front View IrDA Speaker Stylus Battery compartment Back View Model 730 Color Mobile Computer 5
Scanner trigger IrDA Scanner trigger or Recorder button left side of unit Linear Imager lens Secure Digital (SD) card slot Charging/Docking connector Headset jack Microphone Setting Up Your Model 730 1 Unclip Hand Strap and move Hand Strap out of the way. Hand strap clip-in slot 2 Battery pack Remove Battery Pack and insert new or fresh pack. Replace Hand Strap when done.
1 Insert SD card (if applicable). 1a Remove the cover screw and lift cover off 1b Insert SD Card into card slot with label side toward keypad. 1c Reinstall cover 2 Connect to AC Adapter or dock (dock not shown). 3 Charge battery pack (4 hours) before using. However, to ensure proper charging, perform the remaining steps first, with the AC adapter or dock connected. 4 The first time you turn on your Model 730 it boots to the operating system.
Learning About The Keypad Gold Plane Keys The Gold b plane keys provide you access to display controls, special characters, and Windows Mobile 2003 options. Press the gold b key for each gold plane key stroke you wish to make. For example to turn on the front light, press and hold the gold b key plus the 3 key. To turn the front light off press and hold the gold and the 3 key again. Alpha (Blue) Plane Keys-Numeric Keypad The Alpha (Blue) F plane keys work a bit differently than the gold plane keys.
S Yellow: When keypad is in alpha mode, the LED momentarily changes from red to yellow indicating a ‘good scan’. This LED is also the Windows Mobile 2003 Notification signal. It blinks yellow at regular intervals indicating a Calendar or Task activity occurred. Action and Up/Down Navigational Buttons S Action button: Press to open an item (similar to pressing ENTER on the keypad). S Up/Down controls: Press to scroll through a list (similar to pressing the arrow keys on a keyboard).
S Yellow: Your Model 730 is on a charging source and there is no battery pack installed. Can also mean that your Model 730 is out of charging range 32° to 122°F (0° to 50°C). Once your Model 730 gets back in range, charging resumes and the LED changes to red or green. S Alternating between Red and Yellow: The battery pack needs to be replaced. About Microsoft Windows Mobile 2003 software for Pocket PC Your Model 730 comes with Microsoft Windows Mobile 2003 software preloaded.
Tap to switch to a program Tap to change date and time Tap to establish ownership info Your day at a glance Tap to create a new item Model 730 Color Mobile Computer 11
Navigation Bar and Command Bar The Navigation Bar is located at the top of the screen. It displays the active program and current time, and allows you to switch to programs and close screens. The Command Bar is displayed at the bottom of the screen. Use the menus and buttons to perform tasks in programs. Pop-up Menus With pop-up menus, you can quickly choose an action for an item.
Entering Information into Your Model 730 You can enter information in any program on your Model 730 by typing on the keypad or by using one of the on-screen imput options, such as Block Recognizer. For more information regarding the options shown in the following pop-up menu, refer to the 700 Series Color Mobile Computer User’s Manual (p/n: 961-054-031). Tap on the keyboard icon at the bottom of the Command bar To change your option, tap on the preferred choice.
Battery Management To maximize the life of your batteries, your mobile computer can be set to automatically suspend (turn itself Off). The timeout period is set through the Setting>System>Power menu. Options are 1-5 minutes with the default being 3 minutes.
Linear Imager Your Model 730 comes preloaded with software needed to read barcodes using the Linear Imager. To modify the default settings, use the Data Collection Applet. Data Collection Applet To change any default settings tap Start>Settings>System> then the Data Collection applet. For more detailed explanation of bar codes refer to the 700 Series Color Mobile Computer User’s Manual (p/n: 961-054-031).
Wireless Printing To check your wireless printing connection tap Start>Settings>Connections> then the Bluetooth applet. For more detailed explanation of wireless printing refer to the 700 Series Color Mobile Computer User’s Manual (p/n: 961-054-031). Select Connections tab and the Bluetooth applet. To change your wireless printing so it connects to remote devices tap the On radio button.
Wireless Network To change any default setting tap Start>Settings>System> then the Wireless Network applet. For more detailed explanation of wireless printing refer to the 700 Series Color Mobile Computer User’s Manual (p/n: 961-054-031). Select System tab and Wireless Network applet Warm Resetting Your Model 730 A warm reset may be necessary to correct conditions where an application stops responding to the system.
Cold Resetting Your Model 730 In some cases where the Model 730 completely stops responding, it may become necessary to perform a Cold Reset. Because cold resetting may result in data loss, it is not recommended unless all other recovery methods have failed. Cold booting deletes all programs and data stored in RAM including the Object Store. Ensure that data is backed up to the Host PC or a Storage Card before cold booting. 1 Release the lower clip of the hand strap. 2 Remove the battery pack.
The Battery may be critically low.Ensure that your computer has been on a charger for at least five minutes, then remove from the charger and press the I button. The display will then be active.Continue to charge your mobile computer for 4 hours to ensure that the battery is fully charged. Model 730 will not turn On when placed in a dock Ensure that the dock is plugged in and your computer is securely seated in the dock.
CLEAN II cleanser, made by Foresight International, Inc. 4887 F Street, Omaha, NE 68127-0205 (phone: 1-800-637-1344). Where to Find More Information S Intermec Developer’s Library CD (p/n: 235-114-001) which contains the 700 software developer’s kit (SDK). The SDK is used by application developer’s to access features such as radios and scanners. S Windows Mobile 2003 Companion CD used for setting up ActiveSync and also includes some Windows Mobile 2003 applications.
FOR A REFUND. ANY USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT). GRANT OF SOFTWARE LICENSE. This EULA grants you the following license: · DEVICE Software. You may use the DEVICE Software as installed on the DEVICE. · COMPANION CD. A Companion CD is included with your DEVICE, and you may install and use the Microsoft® ActiveSync® 3.
tent, MS DRM SOFTWARE will notify you that a DRM Upgrade is required and then ask for your consent before the DRM Upgrade is downloaded. Third party DRM Software may do the same. If you decline the upgrade, you will not be able to access content that requires the DRM Upgrade; however, you will still be able to access unprotected content and Secure Content that does not require the upgrade. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS. · Speech/Handwriting Recognition.
poration or Intermec Technologies Corporation’s third-party representative, the following additional terms shall apply: (i) you may not transfer the SOFTWARE to another user as part of the transfer of the DEVICE, whether or not a permanent transfer of the SOFTWARE with the DEVICE is otherwise allowed in this EULA; (ii) your rights with respect to any SOFTWARE upgrades shall be as determined by the lease you signed for the DEVICE; and (iii) you may not use the SOFTWARE after your lease terminates, unless you
granted under this EULA are reserved by MS and its suppliers (including Microsoft Corporation). EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is subject to U.S. export jurisdiction. You agree to comply with all applicable international and national laws that apply to the SOFTWARE, including the U.S. Export Administration Regulations, as well as end-user, end-use and destination restrictions issued by U.S. and other governments. For additional information, see http://www.microsoft.com/exporting/.
5 COMPANY’S SUPPLIERS SHALL NOT BE HELD TO ANY LIABILITY FOR ANY DAMAGES SUFFERED OR INCURRED BY THE END USER (INCLUDING, BUT NOT LIMITED TO, GENERAL, SPECIFIC, CONSEQUENTIAL OR INCIDENTAL DAMAGES INCLUDING BUSINESS INFORMATION AND THE LIKE), ARISING FROM OR IN CONNECTION WITH THE DELIVERY, USE OR PERFORMANCE OF THE SOFTWARE PROGRAM. Global Services and Support Warranty Information To understand the warranty for your Intermec product, visit the Intermec web site at http://www.intermec.
Telephone Support These services are available from Intermec Technologies Corporation. In the U.S.A. and Canada call 1-800-755-5505 and choose this option Service Description Factory Repair and On-site Repair Request a return authorization number for authorized service center repair, or request an on-site repair technician. 1 Technical Support Get technical support on your Intermec product. 2 Service Contract Status Inquire about an existing contract, renew a contract, or ask invoicing questions.
Patent Information This product is protected by one or more patents.
Corporate Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com E 2003 by Intermec Technologies Corporation. All rights reserved.
