User's Manual

578-100-0xx Revision A Page 1 of 2
*578-100-0xx*
*578-100-0xx*
Compliance Statement Insert
Device Name: Hand-held Computer Model Number: 6110
The responsible party for the compliance of this device is: Intermec Technologies Corporation
6001 36
th
Avenue West
Everett, WA 98203 USA
[phone]
CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can
result in personal injury, fire, or battery explosion.
This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals
approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this
product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in
the loss of the users authority to operate the equipment.
RIM 902 Mobitex Radio Users FCC ID: EHAWANRIM902-6100
WARNING. Per the FCC RF (radio frequency) exposure requirements:
(1) Antennas must be supplied and installed as recommended by Intermec Technologies Corporation to ensure compliance to
FCC RF exposure requirements.
(2) The user shall not touch the terminal antenna and must remain 22-mm (7/8 of and inch) from the center of the antenna
while the transceiver is in use.
(3) When installing and using Intermec approved remote antennas associated with the vehicle dock, a 23-cm (9-inch) passing
distance must be maintained from any body part of the user, or near-by persons, and the remote antenna.
(4) Cables attached to the remote antennas must have a minimum length of 183-cm (6 feet) to provide the proper losses to
control RF exposure.
(5) The correct mounting for external or remote antennas is on a ground plane (e.g., a vehicle rooftop) with the antenna
positioned such that the minimum 23-cm distance is maintained from any edge of the vehicle rooftop to the remote antenna.
RIM 802 ARDIS Radio Users FCC ID: EHAWANRIM802
WARNING: per the FCC RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF
exposure requirements.
(2) The user shall not touch the terminal antenna and is to remain 15-mm (5/8 of and inch) from the center of the antenna while
the transceiver is in use.
(3) When installing and using Intermec approved remote antennas associated the vehicle dock, a 20-cm (8-inch) passing
distance must be maintained from any body part of the user or near by persons and the remote antenna.
(4) Cables attached to the remote antennas must have a minimum length of 183-cm (6 feet) to provide the proper losses to
control RF exposure.
(5) The correct mounting for external or remote antennas would be on a ground plane (vehicle roof), and positioning the
antenna such that the minimum 20 cm is kept from any edge of the vehicle rooftop and the remote antenna.
INTERMEC RFID 2450 PC Card Radio Users FCC ID: EHARFID2450PCC-5
WARNING: per the FCC RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF
exposure requirements.
(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna
while the transmitter is in use.
INTERMEC RFID 2450 PC Card Radio Users Canada ID: xxxxxxxxxx
WARNING CANADA USERS: To prevent radio interference to the licensed service, this device is intended to be operated
indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is
subject to licensing. The end user is responsible to obtain the license.
WARNING: per Canada RSS-102, RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF
exposure requirements.
(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna
while the transmitter is in use.