Intermec Technologies Corporation Corporate Headquarters 6001 36th Ave. W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec.
Contents Contents Before You Begin .....................................................................................................vi Safety Summary.........................................................................................vi Safety Icons ..............................................................................................vii Global Services and Support .....................................................................vii Who Should Read This Document? .......................
Contents Scanning Bar Codes With the 2D Area Imager.........................................21 Attaching a Tethered Scanner...................................................................22 Using the SD Card .................................................................................................23 2 Configuring the CK30 ...................................................................................25 How to Configure the CK30 ...............................................................
Contents 4 Troubleshooting and Maintaining the CK30 .............................55 Problems and Solutions ..........................................................................................56 Problems While Operating the Terminal..................................................57 Problems While Configuring the Terminal...............................................57 Problems While Configuring 802.1x Security...........................................58 Problems With RF Connectivity..............
Before You Begin Before You Begin This section provides you with safety information, technical support information, and sources for additional product information. Safety Summary Your safety is extremely important. Read and follow all warnings and cautions in this document before handling and operating Intermec equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the safety warnings and cautions.
Before You Begin Safety Icons This section explains how to identify and understand dangers, warnings, cautions, and notes that are in this document. You may also see icons that tell you when to follow ESD procedures and when to take special precautions for handling optical parts. A warning alerts you of an operating procedure, practice, condition, or statement that must be strictly observed to avoid death or serious injury to the persons working on the equipment.
Before You Begin Disclaimer of warranties: The sample code included in this document is presented for reference only. The code does not necessarily represent complete, tested programs. The code is provided “as is with all faults.” All warranties are expressly disclaimed, including the implied warranties of merchantability and fitness for a particular purpose. Web Support Visit the Intermec web site at http://www.intermec.com to download many of our current manuals in PDF format.
Before You Begin Who Should Read This Document? The CK30 Handheld Computer User’s Manual provides you with information about the features of the CK30, and how to install, operate, maintain, and troubleshoot them. Before you install and configure the CK30, you should be familiar with your network and general networking terms, such as IP address. Related Documents The Intermec web site at http://www.intermec.com contains many of our documents that you can download in PDF format.
Before You Begin x CK30 Handheld Computer User’s Manual
1 Using the CK30 Handheld Computer Use this chapter to familiarize yourself with the CK30 Handheld Computer.
Chapter 1 — Using the CK30 Handheld Computer Introducing the CK30 Handheld Computer The Intermec CK30 is the first in a new line of ergonomically designed handheld computers built on the Microsoft® Windows® CE .NET operating system. It is a lightweight, easyto-use, reliable computer that enables you to use legacy applications as well as develop applications based on the latest technologies. The CK30 supports programming tools such as VB.NET, C#, JavaScript, and XML.
Chapter 1 — Using the CK30 Handheld Computer Understanding the CK30 Models and Options The CK30 computer is available in three different models that consist of different options. To find out which model of the CK30 you have, locate the configuration label on the back of the computer. The first five letters of the configuration number indicate the model of CK30 you ordered. For example, the label in the following illustration is for a CK30 model A (CK30A).
Chapter 1 — Using the CK30 Handheld Computer ™ CK30 Handheld Computers with an IEEE 802.11b radio installed are Wi-Fi certified for interoperability with other 802.11b wireless LAN devices. Use this manual to understand how to use the features and options available on the CK30.
Chapter 1 — Using the CK30 Handheld Computer The lithium-ion battery pack that is used in this device may present a fire or chemical burn hazard if it is mistreated. Do not disassemble it, heat it above 100° C (212° F) or incinerate it. Avertissement: Le paquet de piles d’ions de lithium qui est utilisé dans cet appareil peut presenter un risque feu ou un risque chimique de brûlure s’il est maltraité.
Chapter 1 — Using the CK30 Handheld Computer Checking the Battery Status The easiest way to tell the status of your battery is to look at the battery icon in the status bar of your CK30. Icon Status Battery has a full charge. Battery has a medium charge. You should be able to work for several more hours before changing batteries. Battery is low. You need to replace the battery now.
Chapter 1 — Using the CK30 Handheld Computer To install the battery • Insert the tabs on the bottom of the charged battery into the CK30 and snap the battery into place. Battery latch AB1 battery Using the Keypad Your CK30 has one of the following keypad overlay options: • 42-key large numeric and function • 50-key full alphanumeric • 52-key full alphanumeric Each of these keypads also comes in an International version. The International keypads support French, German, Italian, Portuguese, and Spanish.
Chapter 1 — Using the CK30 Handheld Computer Using the 42-Key Large Numeric and Function Keypad Scan button Backlight key Enter Enter Ins Orange key / CAPS Green key \ Home Del [ < ] Sp > Power key PROG 42-key large numeric and function keypad: Use this keypad to easily print numbers (0-9) and access function keys F1 through F12. You can also print the entire alphabet and special characters by pressing color-coded key sequences.
Chapter 1 — Using the CK30 Handheld Computer Using the 50-Key Full Alphanumeric Keypad Backlight key Power key + ‘ “ ? Green key Orange key 50-key full alphanumeric keypad: Use this keypad to easily print numbers (0-9) and the entire alphabet. You can access Function keys (F1-F9) and special characters, symbols, and functions by pressing color-coded key sequences. Note: The 50-key keypad does not have a scan key because it was designed to work with the AH1 handle that has a built-in scanner trigger.
Chapter 1 — Using the CK30 Handheld Computer Using the 52-key Full Alphanumeric Keypad Backlight key Tab Scan button Enter Enter & * Ins Home Orange key Green key ^ F5 F6 F7 + F8 Sp Shift Ctl Del / \ Alt CAPS [ ] , F9 F10 F11 F12 F13 F14 F15 F16 F18 F19 F20 F21 < > F17 F22 F23 X F24 Z Power key 52-key full alphanumeric keypad: Use this keypad to easily print numbers (0-9) and the entire alphabet.
Chapter 1 — Using the CK30 Handheld Computer Understanding How to Use the Keypad Each keypad available for the CK30 provides color-coded keys to let you to access additional characters, symbols, and functions printed on the keypad overlay. Once you understand how to use the color-coded keys and key sequences, you will know how to access all of the additional features printed on the keypad overlay. There are two color-coded modifier keys on the CK30: the Green key and the Orange key.
Chapter 1 — Using the CK30 Handheld Computer Capitalizing All Characters To type all alphabetic characters as uppercase letters, you can do one of the following: • Enable the Caps lock feature. For help, see the next procedure. • Use the Keypad Caps Lock configuration command. For help, see "Keypad Caps Lock" in Chapter 6 of the CK30 Handheld Computer Configuration Manual. To enable Caps lock 1 Press Orange key to activate the modifier key. The Orange modifier key icon appears in the status bar ( ).
Chapter 1 — Using the CK30 Handheld Computer Using the TE 2000 Keypad The CK30 supports TE 2000 VT100/220/320/340 and ANSI, TE 2000 5250, and TE 2000 3270. When you order the CK30 with a TE 2000 application, you also receive the corresponding keypad overlay. Use the TE 2000 keypad overlays to enter the same keys that you can enter on a VT/ANSI keyboard, an IBM 5250 keyboard, or an IBM 3270 keyboard.
Chapter 1 — Using the CK30 Handheld Computer Using the Screen The CK30 can have either a color or monochrome display depending on the model. Both screens are 160 x 160 pixels: the client area is 160 x 140 pixels and the status bar is 160 x 20 pixels. In addition, the screens support double-byte characters, user-programmable fonts, and bitmap graphics. Client area Status bar Navigating on the Screen There are several ways to navigate through the CK30 screens.
Chapter 1 — Using the CK30 Handheld Computer CK30 Screen Icons Icon Description Battery has a full charge. Battery has a medium charge. You should be able to work for several more hours before changing batteries Battery is low. You need to replace the battery now. Strong connection to the network. Medium-strength connection to the network. Weak connection to the network. No connection to the network. No Ethernet connection. Ethernet connection. Orange modifier key pressed. Green modifier key pressed.
Chapter 1 — Using the CK30 Handheld Computer To rotate the screen 90 degrees clockwise • Press Alt, a Programs Programs Using the Mouse Pointer If you need to use a mouse to perform an action in the Windows environment, you can use the mouse pointer that came on your CK30. To turn on the mouse pointer • Press Alt key, b key. The mouse pointer can simulate single-clicks, double-clicks, right mouse button, middle mouse button, and left mouse button functions.
Chapter 1 — Using the CK30 Handheld Computer Moving the mouse pointer around the screen is very easy. You just need to press the appropriate number key that is associated with the direction you want the mouse pointer to move. Using the numeric keypad to move the mouse pointer To continue moving the mouse pointer in one direction • Press and hold the number key that corresponds to the direction you want to move.
Chapter 1 — Using the CK30 Handheld Computer Use this table to understand what the CK30 LEDs mean. LED Name Icon Description User-defined Use the CK30 Programmer’s Software Kit (PSK) to program these LEDs to turn on and off for any task or error within your application. For help, see the CK30 Programmer’s Software Kit (PSK) Reference Manual. Battery status LED Status What it means Off The battery is fully charged On The battery is low. Replace the battery.
Chapter 1 — Using the CK30 Handheld Computer You can change the beep volume and duration to accommodate your needs and environment. When you change the beep volume, you also change the keyclick volume if you have the Keypad Clicker command enabled. The keyclick is the sound you hear when you press a key. You can set the beep volume to off, low, medium, and high (default). Use one of these three ways to change the beep volume: Method Procedure Use the keypad.
Chapter 1 — Using the CK30 Handheld Computer When you unpack the CK30, these bar code symbologies are enabled: • Code 39 • Code 128 • UPC/EAN • PDF 417 (with Model C only?) If you are using bar code labels that are encoded in a different symbology, you need to enable the symbology on the computer. Use the Configuration Utility to enable and disable symbologies for your scanner.
Chapter 1 — Using the CK30 Handheld Computer When the CK30 successfully reads a bar code label, you will hear a high beep and the green Good Read LED turns on briefly. 4 Release the Scan button. Scanning Bar Codes With the 2D Area Imager The CK30C may have a 2D area imager instead of the conventional laser scanner. Omni-directional (360°) scanning means that you can position the CK30 in any direction to scan a bar code label.
Chapter 1 — Using the CK30 Handheld Computer When the CK30 successfully reads a bar code label, you will hear a high beep and the green Good Read LED turns on briefly. 4 Release the Scan button. Attaching a Tethered Scanner You can use a tethered scanner with the CK30 if you ordered it with a 10-pin tethered scanner port in place of the integrated scanner.
Chapter 1 — Using the CK30 Handheld Computer 2 Insert the scanner 10-pin connector until it locks in place. Scanner port To scanner Using the SD Card You can use an SD card to increase file storage and install software. The CK30 supports the following type of SD card: • SanDisk SD cards supporting 1-bit mode only The SD card slot is located on the top of the CK30 just above the laser scanner window. The SD card will appear in the File Manager as "SDMMC Disk.
Chapter 1 — Using the CK30 Handheld Computer 3 Gently insert the SD card into the CK30 with the printed side facing the front of the CK30. 4 Push the card into the slot until it fits firmly. 5 Replace the cover and two screws.
2 Configuring the CK30 Use this chapter to understand how to configure the CK30 to communicate in your network.
Chapter 2 — Configuring the CK30 How to Configure the CK30 You can configure many operation characteristics of the CK30, such as the bar code symbologies it decodes or the network settings. These characteristics are controlled by configuration parameters. The values you set for these configuration parameters determine how the computer operates.
Chapter 2 — Configuring the CK30 Configuring the CK30 With the Setup Assistant When first setting up the CK30, use the Setup Assistant to set or enable basic network parameters and connect your CK30 to the network. The Setup Assistant is a wizard that guides you through setting the following basic network parameters: • Date and time • SSID (Network name) • 802.
Chapter 2 — Configuring the CK30 Configuring the CK30 With the Configuration Utility Use the menu-driven Configuration Utility to configure the CK30 and view system information. You can access the Configuration Utility while running any application. Opening the Configuration Utility When using the Configuration Utility, you may not see a parameter until you enable or disable a value for another key field. For example, you will not see IP Settings unless you disable DHCP.
Chapter 2 — Configuring the CK30 Use this table to understand your menu options in the Configuration Utility. Configuration Utility Menu Options Menu Option Description Scanners, Symbologies Configure scanner settings and bar code symbologies. Communications Set up network settings including the 802.11b radio and the Bluetooth printer. CK30 Settings Configure settings specific to the CK30 such as the date, time, beeper volume, and backlight timeout.
Chapter 2 — Configuring the CK30 Use this table to understand how to navigate and enter information in the Configuration Utility.
Chapter 2 — Configuring the CK30 2 Press Enter to restore factory defaults. A progress bar appears on the screen to show you the status of restoring the factory defaults. Exiting the Configuration Utility When you exit the Configuration Utility, you leave the password-protected area of the CK30. The password-protected icon ( ) disappears from the status bar. To exit the System Main Menu 1 From the System Main Menu, press Esc or select Exit.
Chapter 2 — Configuring the CK30 You can only change some of the configuration parameters by scanning bar codes. To configure all of configuration parameters, use the Configuration Utility, send commands through the network to your Ck30, or use the Intermec Configuration Utility. For example, you can use the Beep Volume configuration command to adjust the beep volume of the CK30.
Chapter 2 — Configuring the CK30 Using Serial Communications on the CK30 The CK30 has a serial port to transfer data to and receive data from another device via RS-232 communications. You can also insert the CK30 into a communications dock to transmit data to and receive data from a host computer or PC using serial communications. Mainframe File server Terminals Ethernet Serial cable PC CK30 To use serial communications with your CK30 1 Turn off the CK30.
Chapter 2 — Configuring the CK30 • Connect the AD1 or AD2 Communications Dock to the serial port of the other device using a DB9-pin to DB9-pin serial adapter cable. 3 Turn on the CK30. Using RF Communications on the CK30 Make sure all components with antennas are at least 30 cm (1 ft) apart when power is applied. Failure to comply could result in equipment damage.
Chapter 2 — Configuring the CK30 Configuring the Network Parameters for a TCP/IP Network In a TCP/IP network, the CK30 communicates with a host computer directly using TCP/IP for the RF protocol. The access point acts as a bridge to allow communications between the wired network and the RF network.
Chapter 2 — Configuring the CK30 • IP Settings (if not using DHCP) • Network Port 2 Configure the security. The easiest way to configure the network parameters on the CK30 is to use the Configuration Utility. For help, see “Configuring the CK30 With the Configuration Utility” on page 28. Configuring the Network Parameters for a UDP Plus Network In a UDP Plus network, the CK30 communicates with a host computer through the DCS 30X or the G4000.
Chapter 2 — Configuring the CK30 The DCS 30X or G4000 translate UDP Plus packets on the RF network into TCP/IP packets on the wired network and vice versa. The access point acts as a bridge to allow communications between the wired network and the RF network.
Chapter 2 — Configuring the CK30 Using Ethernet Communications on the CK30 You can use the CK30 directly in an Ethernet network if you have ordered Ethernet on your CK30 and you insert it into an AD1 or AD2 communications dock. The communications dock has an Ethernet connector that makes it possible for the CK30 to connect to your Ethernet network.
Chapter 2 — Configuring the CK30 Configuring the CK30 for Bluetooth Wireless Printing You can send information to printers wirelessly using the Bluetooth qualified module by Socket Communications. The Bluetooth technology uses short-range radio links and allows for communications over a ten-meter range. To configure the CK30 for wireless printing 1 Go to Configuration Utility > Communications > Bluetooth. 2 Select Set Wireless Printer to start the Bluetooth device discovery.
Chapter 2 — Configuring the CK30 Bluetooth Parameter Descriptions (continued) Parameter Description Discoverable Makes your CK30 discoverable on the network. Connectable Makes your CK30 connectable on the network. Class of Device Determines how the device appears to other devices during discovery. For more information about using Bluetooth communications, see the Wireless Printing Development Guide available on the Intermec Developer’s Library CD.
Chapter 2 — Configuring the CK30 You can enter either an ASCII key or a hex key that is either 5 bytes or 13 bytes long depending on the capability of the radio. Set a 5-byte value for WEP 64-bit or a 13-byte value for WEP 128-bit. Hex keys must be preceded by 0x and contain 10 or 26 hex numbers.
Chapter 2 — Configuring the CK30 42 CK30 Handheld Computer User’s Manual
3 Managing the CK30 Use this chapter to understand how to manage information on the CK30.
Chapter 3 — Managing the CK30 Accessing the System Main Menu You need to access the System Main Menu to be able to use most of the tools for managing the CK30. Access to the System Main Menu is password protected to ensure that only authorized individuals can use it. To access the System Main Menu 1 From the CK30 splash screen, press Green key, Orange key. 2 In the password dialog box, type intermec and press Enter. The System Main Menu appears.
Chapter 3 — Managing the CK30 Using File Manager File Manager provides the ability to run an executable file, delete a file, or view the properties of a file. To open File Manager • From the System Main Menu, select File Manager. The File Manager screen appears. To run an application 1 Navigate to the folder containing the application file. 2 Select the file by pressing its associated number or by scrolling to it and pressing Enter. The following dialog box appears: 3 Select Run and press Enter.
Chapter 3 — Managing the CK30 To delete a file 1 Navigate to the folder containing the file you want to delete. 2 Select the file by pressing its associated number or by scrolling to it and pressing Enter. 3 From the dialog box, select Delete and press Enter. 4 When the screen asks for confirmation that you want to delete the file, Press Enter. The file is deleted and you remain in the selected folder. To view the properties of a file 1 Navigate to the folder containing the file you want to view.
Chapter 3 — Managing the CK30 Using Task Manager Task Manager provides information about applications running on the CK30. You do not need to use the System Main Menu to access Task Manager - you can access Task Manager at any time.
Chapter 3 — Managing the CK30 The application closes and you return to the System Main Menu. To switch between applications 1 Select the application you wan to close. 2 Select Switch To and press Enter. The application you selected now appears on the screen. Using ActiveSync on the CK30 You can use ActiveSync to establish a connection between your desktop PC and the CK30. ActiveSync allows you to transfer files, synchronize files, perform remote debugging, and other device management activities.
Chapter 3 — Managing the CK30 The ActiveSync Get Connected dialog box 2 Connect the AD1 to your desktop PC with the USB cable 3 Click Next in the Get Connected dialog box. ActiveSync detects a device on the USB port and prompts you to set up a new partnership. 4 In the Set Up a Partnership dialog box, click Next. 5 In the Select Number of Partnerships dialog box, select Yes, I want to synchronize with only this computer and then click Next.
Chapter 3 — Managing the CK30 When the partnership has been established, the following screen appears on your desktop showing the device name of your CK30 and the Connected status. The Microsoft ActiveSync screen An icon also appears in the CK30 status bar indicating that it has established an ActiveSync partnership with your desktop PC.
Chapter 3 — Managing the CK30 Using ActiveSync to Copy Files and Install Applications You can use ActiveSync to copy files to the CK30 and to install applications. Basically, to install an application, you need to copy the .cab file to a directory on the CK30 and then run it. Use the following procedures to learn how to copy files and install applications on the CK30 using ActiveSync. To copy a file to the CK30 1 Connect the CK30 to your desktop PC using ActiveSync.
Chapter 3 — Managing the CK30 4 Right-click the file and click Copy. 5 Place the cursor in the desired folder for your device, rightclick, and click Paste. The file has now been copied to the CK30 and you will be able to see it using File Manager. To install an application on the CK30 1 Open File Manager on the CK30. 2 Navigate to the .cab file you want to install. 3 Select the file by pressing its associated number or by scrolling to it and pressing Enter. 4 Select Run from the dialog box and press Enter.
Chapter 3 — Managing the CK30 3 From the System Main Menu, select Change Password. The Change Password dialog box appears: 4 Type intermec in the Old Password field. 5 Press Tab to move to the New Password field. 6 Type your new password and then press Tab to move to the Retype New field. 7 Type your new password in again. 8 Press Enter. The screen displays a message reading “Password successfully changed.
Chapter 3 — Managing the CK30 54 CK30 Handheld Computer User’s Manual
4 Troubleshooting and Maintaining the CK30 Use this chapter to solve problems you may encounter while using the CK30. You will also find information on booting the computer and routine maintenance.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems and Solutions If you have any problems using the CK30, look in this chapter to find a possible solution. This chapter consists of the following sections: Sections Page Problems While Operating the CK30 4-57 Problems While Configuring the CK30 4-57 Problems While Configuring 802.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems While Operating the Terminal Problem Solution You press Power to turn on the CK30 and nothing happens. Make sure you have a charged battery installed correctly. For help, see “Charging and Installing the Battery” in Chapter 1. The battery may be discharged. Replace the battery pack with a spare charged battery, or charge the battery and try again. The Battery light is on and the terminal beeps once every 15 seconds.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems While Configuring the Terminal (continued) Problem Solution • The terminal may be waiting for another command to complete the configuration change. If you started by scanning the Enter Accumulate command, you must finish the command by scanning the Exit Accumulate command. For help, see Chapter 6, “Configuration Command Reference,” in the CK30 Handheld Computer Configuration Manual.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems While Configuring 802.1x Security Problem Possible Solution The CK30 indicates that it is authenticated by emitting a low beep and a high beep, but it does not communicate with the host. Make sure that the CK30 IP address, host IP address, subnet mask, and default router are properly configured for your network. Note: Do not cold boot the terminal. Cold booting the terminal resets the time and date.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems While Configuring 802.1x Security (continued) Problem Solution • The IP address and secret key for your MobileLAN access point must match the IP address and secret key on your Odyssey server. You may need to re-enter the IP address and secret key on both your MobileLAN access point and Odyssey server. • Your Odyssey server is active and that it can communicate with your MobileLAN access point.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems While Configuring 802.1x Security (continued) Problem Possible Solution The terminal indicates that it is not authenticated by emitting a high beep and a low beep. The root Certificate Authority certificate on your terminal cannot validate the server certificate. This error code appears on the Error Logger screen: 0x513 • Make sure your Odyssey server is using a server certificate that matches the root certificate loaded on your terminal.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems With RF Connectivity (continued) Problem Possible Solution When you turn on the terminal after it was suspended for a while (10-15 minutes or longer), the terminal can no longer send or receive messages over the network. The host may have deactivated or lost your current terminal emulation session.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems With RF Connectivity (continued) Problem Possible Solution The network connection icon is in the status bar, but you cannot establish a terminal emulation session with the host computer. There may be a problem with the host computer, a problem with the connection between the G4000 and the host computer, or a problem with the connection between the access point and the host computer.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems Transmitting Data Through the DCS 30X or G4000 (continued) Problem Solution Sending Buffer Transactions. This is an information message to tell you that buffered transactions are now being sent to the DCS 30X or G4000. You can begin collecting data again once the message clears. Transaction Aborted. The transaction just sent to the DCS 30X or G4000 was not received. Try sending the transaction again. Transmit Error XX, press Enter.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems While Scanning Bar Codes (continued) Problem Solution When you release the Scan button, the Good Read LED does not turn off. The Good Read LED will remain on if you configure the terminal to use edge triggering. If you configure the terminal for level triggering and the Good Read LED remains on, there may be a problem. Press the Scan button again without scanning a bar code label.
Chapter 4 — Troubleshooting and Maintaining the CK30 Problems While Scanning Bar Codes (continued) Problem Solution You scan a reader command, such as Backlight On, and nothing happens. The reader commands are disabled. Scan the Enable Override command shown here to temporarily enable all of the reader commands. When you are finished, remember to disable the override so that your data is not interpreted as a command.
Chapter 4 — Troubleshooting and Maintaining the CK30 Cold Booting the CK30 If the CK30 or application is locked up, follow this procedure to perform a cold boot: To cold boot the CK30 1 Remove the battery. CK 30A A03 0100 0 2 Using a small pointed device (such as the end of a paper clip), press the reset switch on the back side of the CK30. Reset switch 3 Replace the battery. The battery LED on the CK30 will blink three times and the CK30 will start performing the power on sequence.
Chapter 4 — Troubleshooting and Maintaining the CK30 Clean the scanner window and CK30 screen as often as needed for the environment in which you are using the terminal. To clean the CK30, use a solution of ammonia and water. There are no user-serviceable parts inside the terminal. Opening the unit will void the warranty and may cause damage to the internal components. Attention: La terminal ne contient pas de pièces révisibles par l’utilisateur.
A Appendix
Chapter A — Appendix Physical and Environmental Specifications Use the tables in this section to locate technical information about the CK30 and its available features and options. Physical Dimensions Length: 20.3 cm (8.0 in) Width: 8.9 cm (3.5 in) Depth: 5.5 cm (2.15 in), 6.2 cm (2.45 in) with large bottom enclosure Weight: 476 g (16.
Chapter A — Appendix Keypad Options • 42-key large numeric and function keypad, available with programmable, international, 3270 TE, 5250 TE, and VT/ANSI TE overlays • 50-key full alphanumeric keypad, available with programmable, international, 3270 TE, 5250 TE, and VT/ANSI TE overlays • 52-key full alphanumeric keypad, available with programmable, international, 3270 TE, 5250 TE, and VT/ANSI TE overlays Accessories for the CK30 You can use these accessories (sold and ordered separately) with the CK30: A
Chapter A — Appendix the computer, and provides a USB and serial port for each inserted CK30. AG1 Protective Case The protective case provides a clear vinyl covering to protect the display and keypad area. AG2 Protective Boot The protective boot provides additional ruggedness for the CK30. AH1 Handle The handle works with all models of the CK30 and provides a convenient scanning trigger. AL1 Holster and Belt The holster and belt provide an easy way for you to carry the CK30 while not using it.
Chapter A — Appendix Using Hidden Key Sequences Both the standard and international keypads have hidden key sequences to access special characters not printed on the keypad overlay. Use the following tables to understand how to access these hidden functions on the different versions of the keypads.
Chapter A — Appendix 74 CK30 Handheld Computer User’s Manual
Corporate Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.
