6822 Series 80-Column Printer Photo of printer not available at this time User’s Manual
6822 User’s Manual Series 80-Column Printer
B Bluetooth Configuration Commands and Specifications Configuration of the Bluetooth radio and software is accomplished using the Bluetooth Configuration Commands listed in this appendix.
Appendix B — Bluetooth Configuration Commands and Specifications Using Configuration Commands All printable characters can be entered directly via the keyboard. Any non-printable characters are entered in binary data format. Numbers are in decimal format except numbers with: • an h suffix are in hexadecimal • a “0x” prefix are in hexadecimal • a “b” suffix are in binary Binary data format is any non seven-bit ASCII data to transmit to the module is encoded in the Internet percent notation.
Appendix B — Bluetooth Configuration Commands and Specifications • Commands that fail return the four character sequence NAK • Commands that are accepted return the four character sequence ACK • Commands that return payload data use the format: is one character from the set: [a-z] is one character for the set: [0-9] is variable in length. is the command terminator.
Appendix B — Bluetooth Configuration Commands and Specifications Command and Control Modes Query Mode Commands Command Function ? ?F0 ?L ?C0 ?C1 ?D0 ?D1 ?S1 ?S2 ?S4 ?T0 ?B0 Read ACK Read Friendly Name Read Security Mode Read Connectable Mode Read Page Scan Timing Read Discoverable Mode Read Inquiry Scan Timing Read Class of Device Read Service Name Read PIN Code Read Shutdown Timeout in minutes Read Bluetooth Addresses of all the paired devices Command R
Appendix B — Bluetooth Configuration Commands and Specifications Note: These commands are only available over the serial link, not over the air and are not available when the device is in the “Bluetooth Link Active State.
Appendix B — Bluetooth Configuration Commands and Specifications Example “C0OFF” — Become non-connectable “C0ON” — Become connectable Specify Page Scan Timing Command C1,< CR> Description Sets the Page Scan timing parameters Default 4096,18 Example “C11024,512” Note: To enable scanning, the values for Interval and Window must be in the range of 18 to 4096. The Window value must be less than the Interval value.
Appendix B — Bluetooth Configuration Commands and Specifications Set Encryption/Authentication: “PIN CODE” Command S4 Description PIN Code — Pin code can be NULL and as long as 16 characters Default “S4%00” NULL PIN code Example “S4MyPinCode ” Manage Security Modes This command controls the security access mode and device pairing.
Appendix B — Bluetooth Configuration Commands and Specifications In Mode L3, only one device is allowed to connect. This device is paired and bonded and needs to supply the PIN code only on the initial connection. Note: Some of the Bluetooth user interfaces cannot supply a NULL string as a PIN code. Use the S4 command to specify a PIN code that is not NULL.
Appendix B — Bluetooth Configuration Commands and Specifications Set Shutdown Timing Command T0
Appendix B — Bluetooth Configuration Commands and Specifications The Bluetooth adapter allows for four states or modes to be available. Each state is dependent upon either the pin states on the terminal holder connector or the programming connector on the adapter described later.
Appendix B — Bluetooth Configuration Commands and Specifications 700 Series or CK60 to 6822 Pass Through Note: Pass through printing requires shutting down the Bluetooth portion of the adapter. To reenable Bluetooth functionality after you finish pass through printing, press a button on the control panel to wake the printer.
Appendix B — Bluetooth Configuration Commands and Specifications Power Management Flow Diagram Bluetooth Power Management Flow Diagram 144 6822 Series 80-Column Printer User’s Manual
Appendix B — Bluetooth Configuration Commands and Specifications Radio Power On/Off Mechanism Note: The shutdown timer configuration is addressed in Appendix A “Bluetooth Configuration Commands”. As stated earlier, the Bluetooth adapter, including the Bluetooth radio shuts down after a configurable time (default is two hours of idle time). To wake the Bluetooth adapter, the 6822 is powered on by any button push on the printer control panel.
Appendix B — Bluetooth Configuration Commands and Specifications • • you have just completed a “pass-through printing” print job • the shutdown time has elapsed (default shutdown time is two hours). Connectability — The default mode is connectable. When configured to be connectable, the printer is connectable at all times, except when: • an active Bluetooth connection exists • you have just completed a “pass-through printing” print job • the shutdown time has elapsed (default is two hours).
Appendix B — Bluetooth Configuration Commands and Specifications • Bondable State [Get/Set] (Authentication) • Encryption State [Get/Set] • Device Name [Get/Set] • Device Address[Get] • Class of Device[Get/Set] • Service Name [Get/Set] • Bluetooth Profile [Get] • Bluetooth Passkey [Set] (Get the fact that it is set) • Radio Shutdown Timeout Bluetooth Performance • Range — Operating range is expected to range from a minimum separation of 10 cm to over 10 m with a 700 Color or CK60.
Appendix B — Bluetooth Configuration Commands and Specifications The Passkey entry either states Not Applicable or Key Present depending on the Authentication state. Applications A 6822 Bluetooth Information application that prints the Bluetooth selftest information on the 6822 can be installed on your 700 Series or CK60. To use the Bluetooth Information application 1 Insert the 700 Series or CK60 in the terminal holder on the 6822.
Appendix B — Bluetooth Configuration Commands and Specifications System Qualification Operation Resilience Normal operation of the Bluetooth system is available in environments with radio backbones, including 802.11b, Spectrum 24, and OpenAir technologies. Environmental Specifications Temperature Operating Temperature -20° to 60°C (-4° to 140°F) Storage Temperature -30° to 70°C (-22° to 158°F).
Appendix B — Bluetooth Configuration Commands and Specifications Vibration Test Results (continued) Test Comments Sweep Duration Directions 10 minutes (half cycle) 1 hour x, y, and z No external or internal damage should be found after the vibration test, and the unit should operate normally. Unpackaged Drop 2 feet to concrete Terminal Inspection Minimum of 30,000 insertions for the terminal holder.
Appendix B — Bluetooth Configuration Commands and Specifications Safety, Regulatory, Agency Requirements (continued) Option Requirement EMC (continued) IEC 61000-4-4Electrical Fast Transients IEC 61000-4-5Surge IEC 61000-4-6Conducted RF IEC 61000-4-8Magnetic Field AC power supply (Europe) Radio Type Approval Additional Approvals IEC 61000-4-11Voltage Dips and Interrupts (AC printers only).
Appendix B — Bluetooth Configuration Commands and Specifications Default Configuration Default Configurations 152 Setting Default Bluetooth Authentication Discoverable Connectable Class of Device Service Name Device Name Baud Rate Data Bits Stop Bits Parity Handshaking Radio Shutdown Timeout Off True True 0x040680 Wireless Printer 6822-DDEEFF 19,200 8 1 None Hardware 120 minutes 6822 Series 80-Column Printer User’s Manual
C Cross-Reference Tables A set of cross-reference tables are provided to assist you in locating control codes and escape sequences. The default settings are also included.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences The following table contains a complete alphabetized list of control codes, including single character control codes and escape sequences, as an aid to locating the control codes defined in Chapter 5 “Control Code Definitions”or detailed definitions of these control codes, refer to the pages shown in the Page column of this table.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Clear Vertical Tabs in Channel Tabs and Tab Setting page 81 Select Vertical Tab Channel Tabs and Tab Setting page 81 Set Vertical Tabs in Channel Tabs and Tab Setting page 81 Character: Define Intercharacter Space Char. Style & Text Mode page 74 Define User-Defined Characters Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Single Byte Character Sets Char. Sets, User Defined page 82 User Defined Characters Char. Sets, User Defined page 86 Code page Selection Char. Sets, User Defined page 83 Disable Printing of Codes 128-255 Char. Sets, User Defined page 88 Enable Printing of Codes 128-255 Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Condensed (compressed): Cancel Condensed Mode Char. Style & Text Mode page 71 Copy ROM to RAM Char. Sets, User Defined Select Condensed Mode Char. Style & Text Mode page 71 D Default Character Set, Select Char. Sets, User Defined page 86 page 87 Define Intercharacter Space Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Select Double Wide Mode Char. Style & Text Mode page 73 Select Double Wide Mode (one line only) Char. Style & Text Mode page 72 E Elite Pitch, Select Char. Style & Text Mode page 74 Emphasized Mode, Cancel Char. Style & Text Mode page 74 Emphasized Mode, Select Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Disable Printing of Character Graphics Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Cancel Half-Speed Printing General Printer Control page 64 Select Half-Speed Printing General Printer Control page 64 Clear Horizontal Tabs Tabs and Tab Setting page 79 Perform Horizontal Tab Tabs and Tab Setting page 78 Set Horizontal Tabs Tabs and Tab Setting page 79 Inactivity Time for Sleep Mode, S
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page General Printer Control page 63 Perform Line Feed General Printer Control page 65 Perform n/216 inch Line Feed General Printer Control page 65 Perform n/216 inch Reverse Line Feed General Printer Control page 65 Select 1/6 inch Line Spacing Page Formatting page 69 Select 1/8 inch Line Spacing Page Form
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Master Reset, Perform Category Page General Printer Control page 65 Mode: 162 Cancel Condensed Mode (compressed) Char. Style & Text Mode page 71 Cancel Double Strike Mode Char. Style & Text Mode page 72 Cancel Double Wide (expanded) Mode Char. Style & Text Mode page 73 Cancel Double Wide Mode (one line only) Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Select Emphasized Mode Char. Style & Text Mode page 74 Select Elite Pitch Char. Style & Text Mode page 74 Select Italic Mode Char. Style & Text Mode page 75 Select Pica Pitch Char. Style & Text Mode page 77 Select Subscript Mode Char. Style & Text Mode page 77 Select Superscript Mode Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Set Page Length (inches) Page Formatting page 68 Set Page Length (lines) Page Formatting page 68 Cancel Skip Over Perforation Page Formatting page 71 Set Skip Over Perforation Page Formatting page 70 P Page: Perforation: Pitch: Select Elite Pitch Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Disable Printing of Codes 128-255 Char. Sets, User Defined page 88 Enable Printing of Character Graphics Char. Sets, User Defined page 89 Enable Printing of Codes 128-255 Char. Sets, User Defined page 88 Expand Printable Code Area Char. Sets, User Defined page 88 Print Character Graphics Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Reverse n/216 inch Line Feed, Perform General Printer Control page 65 Right Margin, Set Page Formatting page 69 ROM to RAM, Copy Char. Sets, User Defined page 86 S Single Byte Character Sets Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Select n/216 inch Line Spacing Category Page Page Formatting page 69 Strike: Cancel Double Strike Mode Char. Style & Text Mode page 72 Select Double Strike Mode Char. Style & Text Mode page 72 Subscript/Superscript: Cancel Subscript/Superscript Mode Char. Style & Text Mode page 78 Select Subscript Mode Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Set Horizontal Tabs Tabs and Tab Setting page 79 Set Vertical Tabs Tabs and Tab Setting page 80 Set Vertical Tabs in Channel Tabs and Tab Setting page 81 Time for Sleep Mode, Set Inactivity General Printer Control page 64 Top-Down Printing, Select General Printer Control page 66 U Underline: Cancel Und
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Category Page Disable Printing of Character Graphics Char. Sets, User Defined page 90 Disable Printing of Codes 128-255 Char. Sets, User Defined page 88 Enable Printing of Character Graphics Char. Sets, User Defined page 89 Enable Printing of Codes 128-255 Char. Sets, User Defined page 88 Expand Printable Code Area Char.
Appendix C — Cross-Reference Tables Control Codes and Escape Sequences Index (continued) Description Set Vertical Tabs in Channel Category Page Tabs and Tab Setting page 81 W Wide: Cancel Double Wide (expanded) Mode Char. Style & Text Mode page 73 Cancel Double Wide Mode (one line only) Char. Style & Text Mode page 73 Select Double Wide (expanded) Mode Char. Style & Text Mode page 73 Select Double Wide Mode (one line only) Char.
Appendix C — Cross-Reference Tables Single Character Control Code Definitions (continued) Dec Hex ASCII Description Page 8 08 BS Backspace: moves printhead one space to left. page 62 9 09 HT Horizontal Tab: moves printhead to next tab stop. page 78 10 0A LF Line Feed: moves paper to next line.
Appendix C — Cross-Reference Tables Single Character Control Code Definitions (continued) Dec Hex ASCII 25 19 EM 26 1A SUB 27 1B ESC 28 1C FS 29 1D GS 30 1E RS 31 1F US 32 20 SP Space Character 127 7F DEL Delete: deletes last character in print buffer. 172 Description Page Escape: defines start of escape sequence.
Appendix C — Cross-Reference Tables Escape Sequence Quick Reference The following table is a quick reference between the escape sequences listed in ascending order, according to numeric values. For detailed definitions, see Chapter 5 “Control Code Definitions”.
Appendix C — Cross-Reference Tables Escape Sequence Quick Reference (continued) Decimal Description ESC “@” Perform Master Reset ESC “A” n Select n/72 inch Line Spacing ESC “B” NUL Clear Vertical Tabs ESC “B” n1 n2 ... nk NUL Set Vertical Tabs ESC “C” n Set Page Length (lines) ESC “C” NUL n Set Page Length (inches) ESC “D” NUL Clear Horizontal Tabs ESC “D” n1 n2 ...
Appendix C — Cross-Reference Tables Escape Sequence Quick Reference (continued) Decimal Description ESC “^” (0) n1 n2 Select 9-pin Single Density Graphics Mode ESC “^” (1) n1 n2 Select 9-pin Double Density Graphics Mode ESC “b” c NUL Clear Vertical Tab Channel ESC “b” c n1 n2 ...
Appendix C — Cross-Reference Tables Factory-Installed Printer Defaults (continued) Function Default Value Keyboard, printer Enabled Language USA Line Spacing 1/6 inch Margin, left 0 Margin, right 80 MSB control Disabled NLQ Disabled Page length 11 inch (66 lines with Pica pitch) Paper end sensor Enabled Pitch Pica (10 characters per inch) Power off sleep timer 10 seconds Printer Code Area Expansion Disabled Printing direction Top-down, bidirectional Redefinition of graphic modes
Appendix C — Cross-Reference Tables Printer Default Settings Function Default Value Zero print option Zeros are printed with a slash Autofeed configuration CR (carriage return added at end of line without line feed) Protocol NPCP (NORAND Portable Communications Protocol) Parity N/A (for NPCP) Bit Rate 19.
Appendix C — Cross-Reference Tables 178 6822 Series 80-Column Printer User’s Manual
D Printer Font Test Jobs This appendix contains a sample print job for each font available on your 6822 printer.
Appendix D — Printer Font Test Jobs About the Printer Font Jobs You can perform these tests yourselves. Load the font of choice from the Toolkit CD into flash memory. After downloading the desired font, use any of the sample print jobs to reveal the character locations within the printer memory. The sample test print jobs are formatted as a memory mapped and could be referenced to select a desired character.
Appendix D — Printer Font Test Jobs Simplified Chinese Character Set This program generates a text file, gb2312.txt, that to copy to a 6822. The text file illustrates the use of the Simplified Chinese character set. Install the Simplified Chinese character font (nft00936.mod) using the Printer Configuration Utility. To have gb2312.txt print correctly 1 Use the Microsoft C version 7.00 compiler. cl china.c /link slibce graphics 2 Run china.exe to create gb2312.txt.
Appendix D — Printer Font Test Jobs 3 Copy this text file to the appropriate printer port. Korean Character Set This program generates a text file, korea.txt, to copy to a 6822. The text file illustrates the use of the KSC5601 character set. Install the KSC5601 character font (nft00949.mod) using the Printer Configuration Utility. To have korea.txt print correctly 1 Use the Microsoft C version 7.00 compiler. cl korea.c /link slibce graphics 2 Run korea.exe to create korea.txt.
I Index 6822 Series 80-Column Printer User’s Manual 183
Index Numerics 4000 Series Terminal Holder 2 61XX Terminal Holder 2 62XX Terminal Holder 2 pinout configuration 122 700 series computer inserting in terminal holder 17 A ActiveSync disabling 54 enabling 46 Alpha keyboard Windows 95/98 38 B Big 5 traditional Chinese character set 82 Bluetooth adapter applications 148 class of device 146 default device name 146 link keys 146 link loss 146, 147 master/slave 146 performance range 147 query items 146 SDP record 146 self-test 147 Bluetooth Configuration Commands
Index Windows 95/98 35 Crossreference tables control codes & escape sequences index 154 D Default configuration file, default.pcf Windows 95/98 printer settings Windows 95/98 default.
Index nptk6820.exe toolkit self-extracting Windows 95/98 O Operation pinfeed holders rpgpconf.exe configuration utility, application Windows 95/98 rpgpconf.
Index Traditional, Bit 5, Chinese character set Troubleshooting Bluetooth adapter diagnostics possible printer problems POST error codes selftest U Utility, configuration installation Windows 95/98 operation 6822 Series 80-Column Printer User’s Manual Windows 2000/XP Windows 95/98 V Verifications printer components Visible moving parts in mechanism W Wall mount printer Working configuration Windows 2000/XP Windows 95/98 187
Index 188 6822 Series 80-Column Printer User’s Manual
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2008 Intermec Technologies Corporation. All rights reserved.
