User's Manual
Table Of Contents
- Document Change Record
- Contents
- Before You Begin
- About the Computer Features
- About the 70 Series Mobile Computers
- 70 Series Accessories
- About Language Provisioning
- About the Battery
- About the Keypad
- Configure the Screen Backlight
- Configure the Screen Brightness
- Adjust the Volume
- About the Imager
- Use the Imager as a Flashlight
- Read Bar Codes
- Read an RFID Tag
- Insert a MicroSD Card
- Transfer Files to and from Your PC
- About the User Interface and Intermec Applications
- Use the Phone
- Use the Camera
- Use GPS
- Configure the Computer
- How to Configure the Computer
- Use Intermec Settings on the Computer
- Use Intermec Settings Remotely with SmartSystems
- About Network Communications
- About Wireless Security
- Manage the Computer
- Manage the Computer in Your Network
- Develop and Install Applications
- RFID Applications and the IF2
- Using the RFID Resource Kit
- Creating RFID Applications for the IF2
- Package Your Application
- Choose a Target Location
- Install Applications Using SmartSystems Foundation Console
- Install Applications Using Microsoft ActiveSync
- Install Applications Using a Storage Card
- Launch Applications Automatically
- Update the System Software
- Troubleshoot and Maintain the Computer
- Specifications and Default Settings
- Physical and Environmental Specifications
- CN70 & CN70 RFID Physical Dimensions
- CN70e & CN70e RFID Physical Dimensions
- CK70 & CK70 RFID Physical Dimensions
- CK71 Physical Dimensions
- Environmental Specifications
- Power and Electrical Specifications
- 70 Series Non-Incendive Computer Specifications
- Operating System
- Hardware
- Back Accessory Interface Pin-outs
- Touch Screen Specifications
- Standard Communications
- Wireless LAN
- Regulatory Approvals
- Bar Code Symbologies
- Imager Reading Distances
- EA30 Typical Reading Distances - Extended Reading Range
- EA30 Area Imager Minimum Reading Distances
- EA30 Area Imager Typical Reading Distances
- EV12 Linear Imager Minimum Reading Distances
- EV12 LInear Imager Typical Reading Distances
- EX25 Near-Far Range Imager Minimum Reading Distance
- EX25 Near-Far Range Imager Typical Reading Distance
- Default Configuration
- Physical and Environmental Specifications
- Keypads and Keystrokes
- ScanNGo Wi-Fi Configuration Bar Codes
- Index
DRAFT
Appendix A — Specifications and Default Settings
142 70 Series Mobile Computer User Manual
EX25 2D Symbologies Typical Reading Distances With 0.24 cm (0.09
in) Setback
** Minimum distance depends on bar code width and scan angle.
Default Configuration
The following tables list the default values of the configuration
settings supported on the mobile computer. If you restore the mobile
computer to factory default settings, the mobile computer uses these
values.
The settings are grouped by function and reflect the organization of
Intermec Settings. Not all of the configuration settings are listed in
this appendix. For detailed information on most of the settings, see the
Intermec Settings Command Reference Manual.
Data Collection Settings
Use data collection settings to configure the imager and to configure
the bar codes that you want the imager to be able to read.
Data Collection Settings
Symbology Density Minimum Distance Maximum Distance
DataMatrix 0.25 mm (10 mils)
0.76 mm (30 mils)
1.4 mm (55 mils)
2.5 mm (100 mils)
7.5 mm (300 mils)
15 cm (5.91 in)
25 cm (9.84 in)
**
**
20 cm (7.87 in)
90 cm (35.43 in)
310 cm (122.05 in)
450 cm (177.17 in)
1100 cm (433.07 in)
1524 cm (600 in)
Data Collection Setting Default Value
Enable Scanner/Camera Port On
BT-Configure On Connect Overwrite with computer settings
Enable Magstripe Reader Disable