User's Manual

2 Switch/3-way Application with
Single-Pole Remote Switch
NEUTRAL
HOT
BLACK
BLUE
120VAC
50/60 Hz
BARE
COPPER
SINGLE
POLE
SWITCH
Incandescent
Lighting Load
RED
HA14
3 Switch Application
NEUTRAL
HOT
BLACK
BLUE
120VAC
50/60 Hz
COMMON
3-WAY
SWITCH
RED
HA14
3-WAY
SWITCH
Incandescent
Lighting Load
ADDITIONAL WIRE
BARE
COPPER
COMMON
Multi-Way Application
NEUTRAL
HOT
BLACK
BLUE
120VAC
50/60 Hz
3-WAY
SWITCH
RED
Incandescent
Lighting Load
4-WAY
SWITCH
4-WAY
SWITCH
3-WAY
SWITCH
HA14
BARE
COPPER
COMMON
COMMON
ADDITIONAL WIRE
2 Switch / 3-way Application with 3-way Remote Switch
NEUTRAL
HOT
BLACK
BLUE
18 ga. MIN (not supplied)
120VAC
50/60 Hz
3-WAY
SWITCH
Incandescent
Lighting Load
RED
HA14
COMMON
NOT
USED
BARE
COPPER
4 Switch Application
NEUTRAL
HOT
BLACK
BLUE
120VAC
50/60 Hz
3-WAY
SWITCH
RED
HA14
4-WAY
SWITCH
ADDITIONAL WIRE
3-WAY
SWITCH
COMMON
COMMON
BARE
COPPER
Incandescent
Lighting Load
Additional Wiring and Installation Diagrams
After including your HA14 In-Wall Dimmer Switch with your
HomeSettings network, you must associate it with a specifi c
control channel (or button) so you can operate it by remote con-
trol. For a non-HomeSettings network, follow controller instruc-
tions provided by the manufacturer.
Decide which pair of 1. ON/OFF buttons you want to use to con-
trol the In-Wall Dimmer. Each pair represents a channel.
Press and hold (at the same time) both
2. ON and OFF buttons
on the HA07 Master Controller or the HA09 Handy Controller.
After about 3 seconds:
The Master Controller screen will display LEARN. -
The Handy Controller lights will rapidly fl ash GREEN and -
RED at the same time.
Release the 3. ON and OFF buttons on the controller.
Press and hold the 4. INCLUDE button on the Master Controller
or the Handy Controller
The Master Controller screen will display INCL. -
The Handy Controller will show a solid GREEN light only. -
While still holding the 5. INCLUDE button, press the top or bot-
tom ROCKER button on the In-Wall Dimmer to adjust the light
to the desired level.
Release the 6. INCLUDE button. If the association is successful:
The Master Controller screen will display SUCCESSFUL. -
The Handy Controller GREEN light will simply turn off. -
Test the channel you have just programmed by pressing its 7.
ON and OFF buttons. The light should power ON or OFF at the
level you have set.
If the screen displays NOT SUCCESSFUL or the light is RED,
the association has failed. Try again. If the procedure contin-
ues to fail, contact Intermatic Customer Service.
3 – ASSOCIATE the In-Wall Dimmer with a Control Channel
If necessary, you can delete the HA14 In-Wall Dimmer Switch
from your HomeSettings network—or any network that sup-
ports Z-Wave devices—through a process called EXCLUSION.
Put the controller into EXCLUSION mode. On the HA07 1.
Master Controller or the HA09 Handy Controller, press and
release the DELETE button. For other manufacturers’ control-
lers, follow the instructions provided by the manufacturer.
Press and release the top or bottom 2. ROCKER button of the
HA14 In-Wall Dimmer. If the exclusion is successful:
The HA07 screen will display SUCCESSFUL. -
The HA09 will show a solid GREEN light for 2 seconds. -
If the screen displays NOT SUCCESSFUL or the light is RED,
the exclusion has failed. Try again. If the procedure contin-
ues to fail, contact Intermatic Customer Service.
Optional: EXCLUDE the In-Wall Dimmer from your Network
After hard-wiring the HA14 into place, the device is ready to join
your HomeSettings network—or any network that supports Z-
Wave™ devices—through a process called INCLUSION.
Put the controller into INCLUSION mode. On the HA07 1.
Master Controller or the HA09 Handy Controller, press and
release the INCLUDE button. For other
manufacturers’ controllers, follow the
instructions provided by the manu-
facturer.
Press and release the top or bottom
2.
ROCKER button of the HA14 In-Wall
Dimmer. If the inclusion is successful:
The HA07 screen will display SUC- -
CESSFUL.
The HA09 will show a solid GREEN light for 2 -
seconds.
If the screen displays NOT SUCCESSFUL or the light is RED,
the inclusion has failed. Try again. If the procedure continues
to fail, contact Intermatic Customer Service.
2 – INCLUDE the In-Wall Dimmer in your Network
For control of permanently installed incandescent lamp •
fi xtures only
Ratings: 600 Watts tungsten, 40 Watts minimum•
120 VAC, 50/60 Hz
Derating: 500 Watts Double Gang, 400 Watts Triple Gang•
Operating Temperature Range: 32°F to 104°F / 0°C to 40°C•
Radio Operating Frequency: 908.42 MHz @ 9.6 kbps•
908.40 MHz @ 40 kbps
RF (wireless) Range: 100 ft. under normal operating conditions•
Made in China•
Technical Information
Our products are constantly evolving. To see if advanced functionality is
possible with your product, look it up at www.homesettings.com.