Owner's Manual

5. Mounttheenclosureinthedesiredlocationusingthe3mountingholes
 provided.
Position at eye level if possible, providing space to the left of the
enclosure for the cover to swing open fully, as shown.
6. Replacethemechanismintheenclosure.
7. Lifttheleftsideoftheplasticinsulatorofftheretainingpostandpivotit
 upandawaytoexposetheterminalstrip.
8. Stripthesupplyandloadwiresto1/2”.
Use AWG#10-#18 copper conductors only.
Knockouts
Mounting holes
1
Neutral
120VAC
Input
Hot
2 3 4
Timer Power
Load
Install jumper
only if timer input
and load voltage
are the same
ET1705 configured for SPST, 120 VAC load
1
Line 2
120/208/240/277
VAC Input
Line 1
2 3 4 5 6
Load
1
Load
2
Timer Power
ET1715 configured for SPDT load switching
1
Line 2
240VAC Input
Line 1
2 3 4 5 6
Line 1
Line 2
Install jumper only if timer input
and load voltage are the same
Timer Power
Load
ET1725 configured for 240VAC DPST load
with jumper set to SIM
1
Line 2
120/208/240/277
VAC Input
Line 1
2 3 4 5 6
ON
Install jumper only if timer input
and load voltage are the same
OFF
Timer Power
ET1725 configured for pulse SPST load
with jumper set to PUL
1
Line 2
120/208/240/277
VAC Input
Line 1
2 3 4 5 6
Load
1
Timer Power
Load
2
ET1725 configured for 2 SPST loads
with jumper set to IND
1
Line 2
120/208/240/277
VAC Input
Line 1
2 3 4 5 6
Load
1
Timer Power
Load
2
ET1725 configured for DPST loads
with jumper set to SIM
Mounting
Holes
Knockouts
Mounting
Hole
9. Insertthewireendsundertheproperterminalplates(seewiringdia-
 gramselsewhereonthispage)andtightenthescrewsrmly.
10. Connectgroundwiretogroundingterminalatbottomofenclosure.
11. Replacetheplasticinsulatorontheretainingpost.
12. Removethebatterycasebyslidingitdownasshownbythearrows,
 theninstall2AAAalkalinebatteries.Makesurethebatteriesarepoint-
 inginthedirectionshown.
13. VerifythatthedisplayisONtomakesurethebatteriesareOK.
If the display shows scrambled information, press the RESET button
to clear it up.
14. ApplypowertotheTimeSwitch.
IMPORTANT:PressandholdtheENTERbutton,thenpresstheRESETbut-
ton.Thescreenwillash12:00AMandMON,andtimerstatusisManual
Mode.
NOTE: You must reset the time switch using this procedure whenever you
change the jumpers.
The Time Switch is now ready for programming.
Programming Overview
BypressingtheMODEbutton,theTimeSwitchwillcyclethroughthe
menusnecessaryforprogrammingthecurrenttime,date,andtimed
events.
ThebasicprocedureistousetheMODEbuttontomovefromone
menutothenext(e.g.,DATE,TIME,etc.),the+or– buttonsforthe
rstpartofasetting(e.g.,MONTH),theENTERbuttontomoveto
thenextpartofthesetting(e.g.,YEAR),thenMODEtoexitandmove
tothenextmenu.Toskipamenu,pressMODEtomoveahead.
If you make a mistake, press the MODE button repeatedly to cycle
back around to the error, then make the correct entry.
NOTE: DATE and TIME must be set before you can access any
other programming menus.
1 – Setting Date
1. PresstheMODEbuttonrepeatedlyuntilthewordsSETand
DATEappearintheupperareaofthedisplay.
2. Pressthe+or–buttonstoenterthecurrentMonth.
3. PresstheENTERbuttonwhentheMonthiscorrecttosavethe
setting.ThescreenadvancestocurrentDate.
4. Againpressthe+or– buttonstoenterthecurrentDate,fol-
lowedbytheENTERbutton.
5. RepeattosetthecorrectYear.
6. PresstheMODEbuttontoexitandadvancetosettingthetime.
Wiring Diagrams