Owner's Manual

ManualsBrandsIntermatic ManualsKitchen30 Amp 7-Day SPST 1-Circuit Electronic Time Switch

Electronic 7-Day

Time Switch

• InputVoltage:120/208/240/277VAC,50/60Hz

• PowerConsumption:6.0wattsmax.

• ContactConguration:SPST(ET1705C),DPST(ET1725C),and

SPDT(ET1715C).Seewiringdiagramsonnextpage.

Switch Ratings—ET1705C, ET1725C (per pole)

• 30AInductive/Resistive:24/120/208/240VAC,60Hz

• 20ABallast:120-277VAC,60Hz

• 20AResistive:28VDC

• 5ATungsten:120/240VAC,60Hz

• 1HP:120VAC,60Hz

• 2HP:240VAC,60Hz

Switch Ratings—ET1715C (NO/NC) Normally Open/Normally Closed Contact

• 20A/10AInductive/Resistive:120/208/240VAC,60Hz

• 20A/3ABallast:120-277VAC,60Hz

• 5A:120/240VACTungsten

• 1HP/¼HP:120VAC,60Hz

• 2HP/½HP:240VAC,60Hz

Set Points (Events)—EachloadoutputoftheTimeSwitchcansupportup

to14timedONand14timedOFFeventsperday.

Battery-Powered Clock Operation—2yearsminimum(uses2AAA

industrialgradealkalinebatteries,supplied)

Minimum ON or OFF time—1minute

Maximum ON or OFF time—6days,23hours,59minutes

Shipping Weight—2.5lb.(1.1kg)

Enclosures—Threeenclosureoptionsareavailable.

• ET17x5C–NEMA1indoormetalenclosure

• ET17x5CR–NEMA3Rindoor/outdoorlockablemetalenclosure

• ET17x5CPD82–NEMA3Rindoor/outdoorlockableimpactresis-

tantpolycarbonateenclosurewithclearcover

Knockouts—Combination1/2-3/4inchsize,1onbackandeachside,

2onbottom

Wire Size—AWG#10through#18

Installation and User Instructions

MODEL ET1700 Series

TheIntermaticET1700SeriesElectronic7-DayTimeSwitchauto-

maticallyswitchesloadstoapresetweeklyschedulewithto-the-

minuteaccuracy.

Theindependent7-dayprogrammingprovidescompleteexibility

forapplicationswhereloadswitchingdifferseachdayoftheweek.

UsetheET1700seriesasanON/OFFtimerinapplicationsrequir-

ing7-dayloadcontrolsuchaslighting,airconditioningsystems,

pumps,etc.EachloadoutputoftheTimeSwitchcansupportupto

14timedONand14timedOFFeventsperday.Theprogramcan

beoverriddenbypushingtheON/OFFloadoverridebutton(s).

TheET1700SeriesTimeSwitchisdesignedtodirectlyswitchtung-

stenorballastloadsuptoitsrating,andinductiveorresistiveloads

upto30Aat120,208,240,or277VAC.

Speciﬁcations

With Battery

Carryover

Description

WARNING: Disconnect the

power to the Time Switch

and the loads before instal-

lation.

1. Remove the mechanism

from the case by de-

pressing the catch at the

top of the case and pull

ing out, as shown.

CAUTION: Do not

touch circuit board

components since

static discharge could damage the microprocessor.

2. Set voltage selector for desired input voltage.

The timer is shipped with voltage set for 120

VAC. To operate at 208, 240 or 277 VAC, move

the selector switch to the desired setting as

marked on the circuit board. See location A in

Rear View above and detail at the right.

3. The timer is shipped with DST (Daylight Saving

Time) enabled. To disable DST, insert a jumper

at location marked DST. See location B in Rear

View above and detail at the right.

4. ET1725C ONLY—Decide whether you want to

control multiple loads simultaneously (SIM),

independently (IND), or with a 2-second pulse

(PUL) (e.g., for use with mechanically held

contactors or bell ringing applications), and make

sure the jumper is positioned accordingly. See location B in Rear

View above and detail at the right. (The unit is shipped with the

loads set for IND.)

Installation Instructions

Slide down

to remove

battery case

Snap out catch

Tilt top forward

Front View

Rear View

• Electrical shock hazard. To avoid ﬁre, shock, or death, disconnect all

power before installing or servicing time switch or connected loads.

• Follow local electrical and safety codes, National Electric Code (NEC)

and Occupational Safety and Health Act Codes (OSHA).

• If the power disconnect point is out of sight, lock it in the OFF position

and tag it to prevent unexpected application of power.

• This time switch must be grounded.

• Do not exceed maximum current carrying capacity.

• Always replace the plastic insulator covering the terminal before

powering ON.

WARNING–Risk of Fire or Electric Shock

Summary of content (4 pages)

PAGE 1
MODEL ET1700 Series Installation and User Instructions Electronic 7-Day Time Switch With Battery Carryover Description The Intermatic ET1700 Series Electronic 7-Day Time Switch automatically switches loads to a preset weekly schedule with to-theminute accuracy. The independent 7-day programming provides complete flexibility for applications where load switching differs each day of the week.
PAGE 2
5. Mount the enclosure in the desired location using the 3 mounting holes provided. 9. Insert the wire ends under the proper terminal plates (see wiring dia grams elsewhere on this page) and tighten the screws firmly. 10. Connect ground wire to grounding terminal at bottom of enclosure. 11. Replace the plastic insulator on the retaining post. 12. Remove the battery case by sliding it down as shown by the arrows, then install 2 AAA alkaline batteries.
PAGE 3
2 – Setting Time Operating the Time Switch 1. If necessary, press the MODE button repeatedly until the words SET and CLOCK appear in the upper area of the display. 2. Press the + or – buttons to enter the current time. NOTE: To go from AM to PM, keep pressing the + or – buttons to cycle through the day. You can hold the + or – buttons down for 3 seconds to make the time scroll quickly. 3. Press the MODE button to exit and advance to setting Events.
PAGE 4