Instructions / Assembly

ManualsBrandsIntermatic ManualsLighting & Ceiling Fans1200-Watt 7-Day Digital Astronomic Landscape Timer, Black

7777 Winn Road

Spring Grove, Illinois 60081

www.intermatic.com

Digtial Landscape Timer

MODEL DT200LT

for use in Low Voltage Transformers up to 1200 W

SET

PROG

ON/OFF

SAFETY SECTION

WARNING

Risk of Fire or Electrical Shock

• Do Not use the timer to control devices that could have dangerous consequences due to inaccurate timing, such as sun lamps, saunas, heaters, crock pots, etc.

• Unplug the timer before replacing batteries.

• Do Not use to control receptacles.

• Installation should be in accordance with national and local electrical code requirements.

NOTICE

• Dispose of product per local regulations for disposal of used batteries.

PRODUCT DESCRIPTION

The Intermatic DT200LT Digital Landscape Timer is a simple-to-use landscape timer to be used with low voltage transformers

up to 1200 W in order to control landscape lighting. This timer supports pre-programmed dawn/dusk times or one set of

custom ON/OFF times.

Specications

Output

• 15 A Resistive, 120 VAC

• 12 A Inductive, 120 VAC

• 1000 W, 120 VAC

• 1/2 HP, 120 VAC

Input

• 120 VAC, 60 Hz, 2.5W max

Operating Temperature

• -40°F to 122°F (-40°C to 50°C), for 1200 W, 120 VAC

Batteries

• Two LR44 batteries that keep time and settings for up

to three months without power

TIMER OVERVIEW

Item Description Item Description

A Battery Holder H Selector Knob

B Low Battery Indicator I Reset Button

C Time of Day Display J Day of the Week Display

D SET Button K Mode Display

E PROG Button L ON/OFF Indicator Light

F ON/OFF Button M Battery Pull Tab

G Grounded Outlet (2)

DAYSAV AUTO CLOCK

YEARDATE

MONTH

SKIP

EVENT

MO TU WE TH FR SA SU AM PM

OFF LOC DUSKDAWN

SET PROG ON/OFF

Summary of content (4 pages)

PAGE 1
7777 Winn Road Spring Grove, Illinois 60081 www.intermatic.com SET PROG ON/OFF Digtial Landscape Timer MODEL DT200LT for use in Low Voltage Transformers up to 1200 W SAFETY SECTION WARNING Risk of Fire or Electrical Shock • • • • Do Not use the timer to control devices that could have dangerous consequences due to inaccurate timing, such as sun lamps, saunas, heaters, crock pots, etc. Unplug the timer before replacing batteries. Do Not use to control receptacles.
PAGE 2
INITIAL SETUP Overview Upon first use, you must enable the battery and then set the Date, Time, and Location. If you make a mistake during any of the programming steps, press the RESET button (I), then press the SET button (D) to cycle through the timer menus until you locate the error and then correct the entry. Enabling the Battery 1. Remove the pull tab (M) from the battery holder, if present. See FIG. 1. 2. When the display shows 12:00 AM, the timer is ready for initial set up. See FIG. 2.
PAGE 3
6. Turn the selector knob (H) to select the state you are in. Press SET (D). See FIG. 5. LOC 7. Turn the selector knob (H) to select the section of the state you are in. Press SET (D). See FIG. 5. D SET PROG ON/OFF H FIG. 5 Setting the State 8. Turn the selector knob (H) to select the time zone you are in. Press SET (D). See FIG. 6. D SET PROG ON/OFF H FIG. 6 9. Turn the selector knob (H) to adjust the DAWN offset time (+/- 15, 30, 45 or 60 minute increments). Press SET (D).
PAGE 4
OPTIONAL – Overriding the Programmed ON/OFF Times Press the ON/OFF (F) button to override the pre-programmed ON/OFF time until the next ON/OFF time occurs. OPERATION Operating the Timer Plug the timer into an outlet. Ensure the ON/OFF indicator (L) is illuminated. This indicates that the timer is ready and operational. Plug your landscape lighting or low voltage transformer into one of the outlets (G) on the timer. Battery Maintenance The battery voltage is continuously monitored.