Spec Sheet

VT1101M
Video
(Coax)
1 Fiber
62.5/125µ m MM
mounted to back
of camera
VR1100CC
up to 2.5 miles
(4 km)
ifs
ifs
International
Fiber
Systems
Incorporated
203.426.1180
Contact
Closure
Contact
Closure
Specifications
Video
Video Input: 1 volt pk-pk (75 ohms)
Bandwidth: 5 Hz - 10 MHz
Differential Gain: <5%
Differential Phase: <5°
Tilt: <1%
Signal-to-Noise Ratio (SNR): 60 dB
Contact Closures
Status: Normally Open
Wavelength 850 nm, Multimode
Number Of Fibers 1
Connectors
Optical: ST
Power: Terminal Block with Screw Clamps
Video: BNC (Gold Plated Center-Pin)
ElectricaL & Mechanical
Power: 9 - 12 VDC @ 150 mA
10 - 14 VAC @ 200 mA
Max. RG59 Cable Length: 750 ft.
Circuit Board: Meets IPC Standard
Size (in./cm.) (LxWxH)
Surface Mount: 2.5 x 1.6 x 1.0 in., 6.4 x 4.1 x 2.5 cm
Shipping Weight: < 2 lbs./0.9 kg
Environmental
MTBF: > 100,000 hours
Operating Temp: -40° C to +74° C
Storage Temp: -40° C to +85° C
Relative Humidity: 0% to 95% (non-condensing)†
†May be extended to condensation conditions by adding suffix ‘–C’ to model number for conformal coating.
Ordering Information
System Design
PS-12VDC 12 Volt DC Plug-in Power Supply (Included)
PS-12VDC-230 12 Volt DC Plug-in Power Supply, 230 VAC Input (Included if specified at time of order)
Add ‘-R3’ to Model Number for R3 Rack Mount - No Charge (Requires R3 Rack purchased separately)
Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)
*Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget.
♦ All accessories are third party manufactured.
Made in the USA
Complies with FDA Performance
Standard for Laser Products, Title 21,
Code of Federal Regulations, Subchapter J
GE
Security
North America
T 888-GE-SECURITY
888-437-3287
F 503-691-7566
E [e-mail]
Asia
T 852-2907-8108
F 852-2142-5063
Australia and New Zealand
T 613-9239-1200
F 613-9239-1299
Europe
T 44-113-238-1668
F 44-113-253-8121
Latin America
T 305-593-4301
F 305-593-4300
gesecurity.com/ifs
Specifications subject to
change without notice
© 2008 General Electric Company
All Rights Reserved
Agency compliance
Part Number Optical Pwr. Budget Max. Distance*Fibers RequiredDescription
Multimode
62.5/125µm**
1 2.5 miles (4 km)VT1101M 14 dBDual Video Transmitter (850 nm)
VT1101M is compatible with:
VR1000, VR1001, VR1100, VR2100 and VR1100CC
Series Receivers
Accessories♦
Options
VT1101M Series
IFS AM Video Mini Transmitter with
Contact Closure
IFS
®
Line / Fiber Transmission
interlogix.com
OVERVIEW
The IFS VT1101M Series video mini-transmitter supports the
simultaneous transmission of a fixed video signal using AM modulation
and one contact closure on one multimode fiber optic cable. This
con
tact closure allows an add
itional device such as a dome tamper
switch or alarm event input to be added and its signal transmitted back
to the monitoring location. The transmitter is direct camera mountable
eliminating the use of coaxial cable at the camera connection and
will fit in most camera housings. A BNC feed-through coupler is
also supplied to connect to coaxial cable when not mounting the
module directly to the camera. The VT1101M Series video transmitter is
compatible with the IFS VR1000, VR1001, VR1100, VR2100 and
VR1100CC receivers. Plug-and-play design ensures ease of instal-
lation requiring no electrical or optical adjustments. The transmitter
incorporates a power status indicating LED for monitoring proper
system operation. The transmitter is available in a stand-alone
version only.
APPLICATION EXAMPLES
• CCTV (Fixed Video)
SYSTEM DESIGN
STANDARD FEATURES
• AM Video Transmission
• NTSC, PAL, SECAM Compatible
• Full Color Compatibility
• Direct Camera Mountable
• Power Status LED
• Contact Closure
• No In-field Electrical or Optical Adjustments Required
• Comprehensive Lifetime Warranty