TVM-2700 / TVM-3200 / TVM-4200 Monitor User Manual P/N 1072765C-EN • REV 1.
Copyright European Union directive © 2014 United Technologies Corporation 2004/108/EC (EMC directive): Hereby, UTC Fire & Security Interlogix is part of UTC Building & Industrial Systems, a unit of declares that this device is in compliance with the essential requirements and other relevant provisions of Directive United Technologies Corporation. All rights reserved. Trademarks and patents 2004/108/EC.
Content Important safeguards 1. Important safeguards 1 Introduction 2 Features 2 Installation cautions: • Do not block any ventilation openings. • Always ensure that the monitor is located in a well-ventilated area to prevent the unit from overheating. • Only use accessories specified by the manufacturer or those sold with the product.
7. 8. Lightning: For added protection during a lighting storm or when this unit is left unattended and unused for long periods of time, unplug the unit from the wall outlet and disconnect the cable system. This will prevent damage to the unit due to lightning and power line surges. Mains plug (2 pin/3 pin): • Do not remove the grounding or earth connection from the power supply / mains plug.
8. 9. CAM2 R/L Audio signal input left and right for CAM2 5. CAM2 In/OUT Composite signal input and output for CAM2 10. CAM1 R/L Audio signal input left and right for CAM1 11. CAM1 In/OUT Composite signal input and output for CAM1 12. S-VIDEO OUT Composite signal output Secondary Function: Allows for vertical scrolling in the OSD menu. 6. ▼ Down Arrow Allows for vertical scrolling in the OSD menu. 7. SOURCE (*) Used to select different input sources.
Hot keys SOURCE ▲ (UP/AUTO) ◀ ▶ (VOLUME) Selects signal in order. VGA - HDMI - DVI – CAM1 – CAM2 - SVIDEO R3 MUTE Turn the sound on and off. R4 NUMBER Buttons Press the number buttons in order of 7,8,9,0 to unlock the keypad lock. When there is no OSD, if you press this ▲ (UP/AUTO) button, you can use the best display performance fit for a current mode R5 LAST CH Not used. R6 When there is no OSD, you can adjust the volume directly INFO Information display.
R21 Not used. Adjustment procedure R22 POSITION Not used. R23 ZOOM Select the screen format (CAM/HDMI mode only). R24 SIZE Not used. R25 SKIP Not used. R26 PIP Not used. R27 S. SWAP Not used. R28 SOURCE Not used. R29 P. SWAP Not used. R30, R31, R32, R33 Not used. Inserting batteries into the remote control unit Open the battery compartment of the remote control. Insert the batteries (two 1.5 V type R03 or AAA).
(Advanced Settings) 4-3 DCR (optional) The dynamic contrast ratio (DCR) automatically adjusts the screen brightness. Turn DCR on or off. 4-4 DCC (optional) The dynamic contrast control (DCC) automatically adjusts the screen contrast. Turns DCC on or off. 5. VGA Setting 5-1 Auto adjust Automatically choose the correct horizontal position and vertical position, and size of the screen image. (VGA setting) 5-2 H-Position Adjust the position of the display horizontally (left or right).
2. Balance Adjust the sound balance of the left and right speakers. 3. Bass (optional) When you select User mode, adjust the bass sound. 4. Treble (optional) When you select the user mode, adjust the treble sound. 5. Equalizer Provides an enhanced listening experience. 6. Auto Volume 2. Screen Format Select the aspect ratio (16:9/4:3). 3. OSD Time out Adjust the display of the OSD menu (5 to 60 seconds). 4. OSD Transparency Adjust the OSD transparency. 5. Power On Status Not used. 6.
1. 2. Keypad Lock 5. Sharpness Turn the keypad lock on or off. Adjust the image quality of the display. Remote Control Lock (optional) (DVI mode is not available). Turn the remote control lock on or off. Cam menu (DVI/ HDMICAM/ SVIDEO) 6. Tint (cam mode only) Adjust the tint of the image. 7. Color Tone Choose a different preset color temperature or set your own customized color parameters (Normal/ Warm/ Cool/ User). Picture 8.
Sound 1. Sound Mode Choose a different preset sound mode or your own customized sound. (Standard/ Movie/ Music/ User) 2. 5. Equalizer Provides an enhanced listening experience. 6. 2. Auto Volume Automatically remains at the same volume level if you change the program. System Screen Format Select the aspect ratio (16:9/4:3/ ZOOM1/ ZOOM2/ FULL(HDMI mode only)). 3. OSD Time out Adjust the display time of the OSD menu (10 to 60 seconds). 4. OSD Transparency Adjust the OSD transparency.
8. Memory Recall Reset the screen to the factory preset display settings. Lock Press any key to cancel. Monitor is turned off when it does not receive any signal from the remote control or any button within the time that set up. Removing the monitor stand (All models) 1. Keypad Lock 1. Turn off the monitor and unplug the power cable. 2. Place a cushion or a soft cloth on the floor and put the monitor on it with the front of the monitor facing the floor. 3.
Troubleshooting Monitor stand attached here Symptom Check Picture is jittery Adjust Clock to set the screen position and adjust the Clock value carefully until there is no noise displayed. No picture Check if the power switch and computer power switch are in the On position. Face of monitor stand arm The monitor’s installation surface is compatible with other types of VESA standard stands. Check if the signal cable is correctly connected to the video card.
Symptom Check Adjust the volume of the sound card in the computer. VIDEO screen cannot be seen Check if PICTURE mode has been set. Check if the video terminal is properly connected. No video Check if the video cable is correctly connected to the computer and set to Functions on the OSD picture menu. Poor color in the video Adjust the Color or Tint values on the OSD Picture menu. Grainy picture in the video Adjust the Sharpness on the OSD Picture menu.
Specifications TVM-2700 / TVM-3200 models Items TVM-2700 TVM-3200 Screen size 27 in. (68.6 cm) 32 in. (81.3 cm) Pixel pitch 0.31125 x 0.31125 mm 0.36375 x 0.
Items Weight VESA mount TVM-2700 TVM-3200 25.35 x 16.85 x 7.87 in. 29.17 x 19.33 x 7.87 in. W x H x D (box) 749 x 542 x 276 mm 29.49 x 21.34 x 10.87 in. 887 x 654 x 293 mm 34.92 x 25.74 x 11.54 in. Net (without stand) 6.9 kg (15.2 lb.) 10.7 kg (23.59 lb.) Net (with stand) 8.5 kg (18.7 lb.) 12.3 kg (27.12 lb.) Gross (box) 11.7 kg (25.8 kg) 16.3 kg (35.94 lb.) VESA standard 100 x 100 mm and 200 x 100 mm 200 x 200 mm and 400 x 200 mm (3.94 x 3.94 in. and 7.87 x 3.94 in.) (7.87 x 15.
Items Interface TVM-4200 model VGA in (15 Pin D-Sub) 1 DVI in 1 HDMI in 1 CAM in/out 2/2 Audio in (RCA type) 2 S-Video in/out 1/1 PC stereo in Yes Head phone out Yes Transmitter Remote control Yes Power Consumption < 90 W Source 90 to 260 VAC Special feature Filter type 3D comb filter, De-interlacing Dimensions W x H x D (without stand) 977 x 590 x 89 mm 38.47 x 23.23 x 3.50 in. W x H x D (with stand) 977 x 636 x 270 mm 38.47 x 25.04 x 10.63 in.
Factory preset timings Pixel Format Horizontal Freq.(KHz) Vertical Freq.(Hz) Remark 720 x 400 31.469 70.087 all models 640 x 480 31.469 59.940 all models 640 x 480 37.861 72.809 all models 640 x 480 37.500 75.000 all models 800 x 600 37.870 60.317 all models 800 x 600 48.077 72.188 all models 800 x 600 46.875 75.000 all models 1024 x 768 48.360 60.000 all models 1024 x 768 56.476 70.069 all models 1024 x 768 60.020 75.030 all models 1152 x 864 59.986 59.
