Quick Start Guide

ManualsBrandsInterlogix ManualsEncoders1 Channel TruVision IP HD-TVI Encoder

P/N 1073659-EN • REV C • ISS 12NOV19 1

TruVision TVE-120-420-820-1620

Encoder Quick Start Guide

Figure

1: Front panel

-channel:

8-channel / 16-channel:

. Audio Out: Connect to speakers for audio output.

. Line In

. Power: The LED lights up RED when the device is working. It is not lit when the device is powered down.

. Video In: Connect a CCTV monitor (BNC-type connectors).

. Audio In: Connect an audio input to RCA connectors.

TX/RX: The LED is not lit when there is no network connection. It lights up green and flashes when data

is being transmitted/received.

Summary of content (8 pages)

PAGE 1
TruVision TVE-120-420-820-1620 Encoder Quick Start Guide Figure 1: Front panel 1-channel: 4-channel: 8-channel / 16-channel: 1. Audio Out: Connect to speakers for audio output. 2. Line In 3. Power: The LED lights up RED when the device is working. It is not lit when the device is powered down. 4. Video In: Connect a CCTV monitor (BNC-type connectors). 5. Audio In: Connect an audio input to RCA connectors. 6. TX/RX: The LED is not lit when there is no network connection.
PAGE 2
Figure 2: Back panel 1-channel / 4-channel 1. Alarm In 5. Reset button 2. Alarm Out / Audio In, RCA connector 6. Micro SD card slot 3. RS-232 serial interface 7. LAN network interface 4. RS-485 serial interface 8. 12 VDC power input 9. GND Figure 3: Back panel 8-channel: 16-channel: 2 1. Video In 6. RS-485 serial interface 2. Audio In, RCA connector 7. 12 VDC power input 3. Audio Out, RCA connector 8. Alarm In/Out 4. RS-232 serial interface 9. Power switch 5. LAN network interface 10.
PAGE 3
Connections Figure 4: Alarm input connections Alarm input connections for Emerson alarm: Alarm input connections for normal alarm: 1. Emerson alarm 2. V output 3. 10 V regulator Package contents The TruVision TVE-xx20 IP video encoder is shipped with the following items: • TVE encoder • Power adaptor (8-ch and 16-ch encoder models only) • Power cable (8-ch and 16-ch encoder models only) • 19” rack brackets (8-ch and 16-ch encoder models only) • Quick start guide 4. 5. 6. 7.
PAGE 4
Australia/New Zealand: www.utcfs.com.au Getting started This guide provides basic information on setting up the TVE-120, TVE-420, TVE-820 and TVE-1620 models. All encoder configuration and control is done via the webpage. Before you start using the encoder, you must first activate the device by setting up a strong password. Default network settings The default network settings are: • IP address - 192.168.1.70 • Subnet mask - 255.255.255.0 • Gateway address - 192.168.1.
PAGE 5
Use the Remote Configuration menu to configure the camera, VCA, network settings, recording, alarm and events setup, device management, user management, and to see system information. See “Encoder menu tree” on page 6 for description of the encoder menu tree.
PAGE 6
Encoder menu tree 6 TruVision TVE-120-420-820-1620 Encoder Quick Start Guide
PAGE 7
Legal and regulatory information 2013/56/EU & 2006/66/EC (battery directive): Copyright © 2019 United Technologies Corporation. All rights reserved. Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. All rights reserved Trademarks and patents Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Disclaimer Information in this document is subject to change without notice.
PAGE 8
TruVision TVE-120-420-820-1620 Encoder Quick Start Guide