TruVision Stainless Steel Dome Camera Installation Guide P/N 1073434-EN • REV A • ISS 27FEB18
Copyright Trademarks and patents Manufacturer © 2018 United Technologies Corporation, Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. All rights reserved. Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Interlogix 2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA Authorized EU manufacturing representative: UTC Fire & Security B.V.
Product warnings and disclaimers THESE PRODUCTS ARE INTENDED FOR SALE TO AND INSTALLATION BY QUALIFIED PROFESSIONALS. UTC FIRE & SECURITY CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER” OR “AUTHORIZED RESELLER”, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL FIRE AND SECURITY RELATED PRODUCTS. For more information on warranty disclaimers and product safety information, please check www.firesecurityproducts.
Content Introduction 6 Product overview 6 Installation 6 Installation environment 6 Package contents 7 Camera description 9 IR illuminators 10 Alarm input and output connections 10 SD memory card installation 11 Mounting the dome camera 12 Mounting the TVJ-JBS junction box 12 Using the camera with an Interlogix NVR or Hybrid DVR or another system 12 Using the camera with TruVision Navigator 13 Access the camera over the internet 13 Specifications 16 Pin definitions 17 Installation Guide 5
Introduction Product overview This is the installation guide for the TruVision Stainless Steel dome camera model: • TVD-5801 (2MPX camera, 2.8-12 mm lens) Installation This section provides information on how to install the cameras. Installation environment When installing your product, consider these factors: • Electrical: Install electrical wiring carefully. It should be done by qualified service personnel.
immediately if the camera is wet and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock. • Servicing: Do not attempt to service this camera yourself. Any attempt to dismantle or remove the covers from this product will invalidate the warranty and may also result in serious injury. Refer all servicing to qualified service personnel. • Cleaning: Do not touch the sensor modules with fingers.
CD with configuration manual and TruVision Device Manager Equipment disposal sheet Battery disposal sheet Drill template Video test cable Screws Drywall anchor 7.5 × 24.
CAUTION: Use direct plug-in UL listed power supplies marked Class 2/CE certified or LPS (limited power source) of the required output rating as listed on the unit. Camera description Figure 1: Dome camera description and connectors 3 2 4 5 1 10 11 12 13 IN DC12V 9 6 7 8 1. Bubble assembly 8. SD card slot 2. Lens 9. Video test port 3. Dome liner 10. Ethernet RJ45 PoE port 4. Rubber sealing 11. Alarm I/O 5. Base 12. Audio I/O 6. Reset button 13. 12 VDC power cable 7.
IR illuminators The camera’s built-in IR illumination provides high-quality video in low-light environments, even when there is no other illumination available. You can configure the IR illumination using a web browser or a client software, such as TruVision Navigator. If the function is enabled, the IR light is On when the camera enters night (black and white) mode. If disabled, the IR light is always Off.
SD memory card installation To install the SD memory card in the dome camera 1. Loosen the three torx screws on the bubble assembly. 2. Insert the memory card into the SD card slot until it clicks into place. 3. Reinstall the bubble assembly on the camera base.
Mounting the dome camera To mount the dome on a wall: The TruVision Stainless Steel Dome Wall Mount (TVD-WBS, not included) is required to wall mount the dome camera. Refer to the installation guides provided with the TVD-WBS wall mount for instructions on mounting the stainless steel dome camera to the wall. To mount the dome on the ceiling: The TruVision Stainless Steel Pendant Mount (TVP-PAS, not included) is required to ceiling mount the dome camera.
Using the camera with TruVision Navigator The camera can be connected to an Interlogix NVR, hybrid DVR, or directly to TruVision Navigator. Please refer to the user manual of TruVision Navigator and/or of the NVR or hybrid DVR for instructions. Access the camera over the internet Use the web browser to access and control the camera over the internet. Note: Any changes made to the camera’s configuration only apply to this camera. Only authorized users should be able to modify camera settings.
Note: 3. • The default IP address of the camera is 192.168.1.70. • For the camera to enable DHCP by default, you must activate the camera via TruVision Device Manager. Please refer to the following section, “To activate the camera via TruVision Device Manager.” Type the password in the Password field. Note: A valid password range must be between 8 and 16 characters. You can use a combination of numbers, lower and upper case letters, and special characters : _ - , . * & @ / $ ? Space.
6. Click the Configuration tab on the top of the screen and select the parameter to change. Figure 3: Example of a configuration window To activate the camera via TruVision Device Manager: For instructions on how to activate the camera using TruVision Device Manager, refer to the TruVision Device Manager User Manual. Go to www.interlogix.com/video/product/truvisiondevice-manager and click Downloads.
Specifications Electrical Voltage input 12 VDC, PoE+ Power consumption Max. 16 W Miscellaneous Connectors Audio In/Out, Alarm In/Out, 12 VDC Power, Ethernet RJ45 PoE port Operating temperature -40 to +60°C (-40 to +140°F) Dimensions 165.4 × 130 mm (6.51 x 5.12 in.) Weight 3.36 kg (7.41 lb.
Pin definitions There are eight wires on a standard UTP/STP cable and each wire is color-coded.
Installation Guide
Installation Guide 19
Installation Guide
