TruVision HD-TVI 1080P Camera Configuration Manual P/N 1073162-EN • REV A • ISS 31MAR16
Copyright © 2016 United Technologies Corporation. All rights reserved. Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. Trademarks and patents The TruVision and Interlogix names and logos are trademarks of United Technologies. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Content Introduction 2 HD-TVI 1080P IR Bullet Cameras 2 HD-TVI 1080P IR Dome Cameras 2 HD-TVI 1080P Box Cameras 2 Programming 3 Using the camera Menu button 3 Using a TVI output 3 TVS-C200 CVBS OSD controller 4 Menu trees 6 TVB-2403/4403 and TVD-2403/4403 cameras 6 TVC-2401/4401 cameras 6 TVB-2404/4404, TVB-2405/4405, TVD-2404/4404 and TVD2405/4405 cameras 7 TVB-2406/4406 cameras 7 Configuration 8 Video Out 8 Languages 8 Setup 8 Smart Focus 8 Scene 8 Lens 8 Exposure 9 Backlight 10 White Balance 11 Day & Nig
Introduction This is the configuration manual for following camera models: HD-TVI 1080P IR Bullet Cameras TVB-2403 (1080P TVI Bullet Camera, Fixed Lens, IR, PAL) TVB-4403 (1080P TVI Bullet Camera, Fixed Lens, IR, NTSC) TVB-2404 (1080P TVI Bullet Camera, VF Lens, IR, PAL) TVB-4404 (1080P TVI Bullet Camera, VF Lens, IR, NTSC) TVB-2405 (1080P TVI Bullet Camera, Motorized Lens, IR, PAL) TVB-4405 (1080P TVI Bullet Camera, Motorized Lens, IR, NTSC) TVB-2406 (1080P TVI Bullet Came
Programming Once the camera hardware has been installed, the camera can be configured using the built-in OSD button, a TVI DVR menu, or the OSD TVS-C200 controller (purchased separately). Note: TVC-2401/4401 does not support the TruVision TVS-C200 OSD controller. Using the camera Menu button For the cameras with built-in OSD button, please press the Menu button to call up the OSD menu and select an OSD item. Press the button up/down to move the cursor up or down to an OSD item.
For more details, refer to the TVI DVR user manual. TVS-C200 CVBS OSD controller Interlogix offers two different versions of the OSD controller: the TVS-C100 controller and the TVS-C200 controller. Please choose the corresponding controller by referring to the product datasheets. The cameras listed in the “Introduction” section support TruVision Coax OSD control protocol and require the TVS-C200 for OSD control. The TVS-C200 is used to program the camera’s 960H CVBS output, not for the TVI video output.
Table 2: Using the OSD control button Button direction Description Up Moves the cursor upward to select an item Left Moves the cursor left to select or adjust the parameters of the selected item. Right Moves the cursor to the right to select or adjust the parameters of the selected item. Down Moves the cursor downward to select an item. OK Press the red button for few seconds to display the Setup menu. If the selected item has its own menu, press the button to enter a submenu.
Menu trees The menu trees of the TruVision 1080P TVI cameras are shown below.
TVB-2404/4404, TVB-2405/4405, TVD-2404/4404 and TVD2405/4405 cameras TVB-2406/4406 cameras TruVision HD-TVI 1080P Camera Configuration Manual 7
Configuration This section describes how to set up the menu settings. Video Out Select PAL or NTSC. Languages Select one of the languages available: English, Japanese, CHN1, CHN2, Korean, German, French, Italian, Spanish, Polish, Russian, Portuguese, Dutch, Turkish, Hebrew or Arabic. Note: The TVB-2406/4406 camera only supports English and Chinese. Setup Smart Focus Enable Smart Focus. Use this feature to remotely sharpen the focus of a lens.
ZOOM SPEED Move the cursor left/right to adjust the zoom speed. PRESET Set the lens pre-set, delete or call pre-configured lens preset. A total of 64 presets can be set. FOCUS MODE Select Manual, Auto, or Trigger mode. Auto mode: The camera focuses automatically. Manual mode: Click Zoom+ and Zoom- to focus. Trigger mode: The image will not refocus if it is changed. LENSINIT Lens initialization. Reset the lens to calibrate it. AFLIMIT Auto Focus Limit.
D-WDR Digital Wide Dynamic Range. Select ON/OFF to enable /disable the function. It helps to balance the brightness level of the whole image. Note: When D-WDR is enabled, the brightness function is disabled. DEFOG During foggy or rainy weather, the camera image becomes hazy. The defog function can increase the image contrast and brightness level to show more detail. Note: Enabling the defog function increases the contrast of the image. It is recommended to set Defog to OFF during normal weather.
value, the brighter the image. WDR OFFSET: Set the offset from 0 to 100. The higher the value, the brighter the dark area of the image. HSBLC Highlight Suppression Backlight Compensation. Use this function to mask strong light sources across a scene and improve image quality. There can be up to four mask areas configured. SELECT: Select an HSBLC area. DISPLAY: Select ON to enter a popup screen. Press the direction buttons to define the area position and size.
MANUAL Adjust the white balance by customizing the Blue and Red value, which range from 1 to 100. MANUAL WB BLUE ---|------ 51 RED ---|------ 50 RETURN RET ATW Select ATW for the white balance to be automatically adjusted according to the scene illumination. AWC→SET If enabled, this function will only adjust the WB once. It is best used in a stable environment. Day & Night Select Color, B/W, EXT and AUTO to switch between day and night mode.
EXT The image switches from color to B/W or from B/W to color automatically according to the light conditions. TRIGGER This function is only available with the TVB-2406/4406 camera. Select Enable/Disable to turn the IR LED ON/OFF. NR Noise reduction (NR) reduces noise, especially in low light conditions, and improves image quality. Select the following options under the NR menu: 2D NR Select ON/OFF to enable/disable the feature. It reduces the noise in a single frame to get a clearer image at night.
Special Use this menu to configure the camera name, digital effect settings for the image, motion detection, privacy mask, dead pixel correction, as well as check the camera version. Select the following options under the Special menu: SPECIAL 1. CAM TITLE 2. D-EFFECT 3. MOTION 4. PRIVACY 5. DEFECT 6. RS485 7. RETURN CAM TITLE ON OFF OFF RET Set the camera name by enabling this function to enter the editing interface. Up to 15 characters can be entered. ON: Display and enter the camera title.
V-FLIP: Image flips 180 degrees vertically. ROTATE: Image flips 180 degrees both horizontally and vertically. D-ZOOM: Set the digital zoom ON to enlarge the image by creating pixels through interpolation. D-ZOOM 1. D-ZOOM 2. PAN & TILT 3. DEFAULT 4. RETURN x 2.0 RET D-ZOOM: Set the zoom factor between 2 and 62. PAN & TILT: Define zoom area in PAN & TILT menus. DEFAULT: Set to restore D-ZOOM back to the default settings.
from 0 to 60. The higher the value, the higher the sensitivity level to trigger an alarm. Note: Branch movement, rain drops, snowflakes, flashing lights in the defined area may be detected and trigger a false alarm. In such cases, adjust the sensitive value. MOTION VIEW: Enabled this feature to trigger a flickering transparent red mosaic on the detected area when motion is detected. Set it to OFF to disable. DEFAULT: Select to restore settings back to default.
AUTO: Detect and repair defective pixels automatically. ON: Repair defective pixels manually, configurable range [0-255], select higher value to repair the defective pixels easily, OFF: Disable DPC function. STATIC DPC: Detect and correct defective pixels manually. Select On/Off to enable/disable. STATIC DPC 1.START 2.LEVEL 3.SENS-UP 4.AGC 5.RETURN ---|------15 x 20 ---|------2 RET START: Start detecting and correcting defective pixels. Press OK when you see the message on the screen.
SHARPNESS Adjust the value from 0 to 15. The higher the value, the clearer and sharper the image appears. MONITOR Select CRT or LCD. CRT: Set the black level [-30 to +30], blue gain [-50 to +50], and red gain [-50 to +50]. CRT 1. BLACK LEVEL 2. BLUE GAIN 3. RE5 GAIN 4.RETURN ----|----+0 ----|----50 ----|----60 RET LCD: Set gamma, blue gain [0 to100], and red gain [0 to100].
