TT3010 TT3010-R3 TT3020WDM TT3020WDM-R3 TT3030 TT3030-R3 TT3030WDM TT3030WDM-R3 TR3010 TR3010-R3 TR3020WDM TR3020WDM-R3 TR3030 TR3030-R3 TR3030WDM TR3030WDM-R3 IFS Fiber Module Installation & Operation Instructions P/N 1062835 • REV B • ISS 01AUG11
TT3010 DIGITAL POTS LINE END OPTICAL OUT LINK STATUS OFF-HOOK ifs OPTICAL IN International Fiber Ring Pin 4 Systems Incorporated PHONE CONNECTION Tip Pin 3 RING DETECT POWER POWER -2 +12 VDC - 1 Black wire Black with white stripe 6 1 Simplex multimode fiber optic cable TR3010 DIGITAL POTS TELEPHONE END OPTICAL OUT LINK STATUS OFF-HOOK ifs OPTICAL IN International Fiber Systems Incorporated PHONE CONNECTION RING DETECT POWER POWER -2 +12 VDC - 1 Black wire Black with white stripe
TT/TR3000 A A B C D Link Status Off-Hook Ring Detect Power B C D LED illuminates NOTE: All units set to USA/Canada standard. WORLD STANDARD JUMPER SETTINGS JUMPER SETTING J6 J7 STANDARD ON ON USA/CANADA OFF ON UK* ON OFF AUSTRALIA OFF OFF JAPAN TT J7 J6 TR J6 J7 * UK includes the following countries: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Portugal, Spain, Sweden, Switzerland.
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by International Fiber Systems, Inc. could void the user’s authority to operate the equipment.
FCC Part 68 Registration Customer Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: FIBOT01BTT3000. If requested, this number must be provided to the telephone company.
PROPER MOUNTING METHOD FOR THE TT/TR3000 1) Locate unit on solid flat horizontal or vertical surface. 2) Position unit no closer than 24 inches from any power source or machinery. 3) Securely mount unit using (4) four mounting screws (not provided). 4) Select the correct voltage requirements for your application, +12VDC or 12VAC. +12VDC attach black w/white stripe wir e to pin 1 and black stripe to pin 2 (GND). For 12VAC connect brown to pin 1, green to pin 2 and blue to pin 3 from adapter.
Product Disassembly Instructions for WEEE Per European Directive 2002/95/EC Waste Electrical and Electronic Equipment Required Tools: One number 2 Phillips (crosstip) screwdriver. One number 2 flat screwdriver. For the enclosed box version: 1. Locate and remove box cover securement screws. Usually, but not limited to at least 4 screws. 2. Lift off box top cover. 3. Locate and remove securement screws for printed circuit board. 4.
Contacting us For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any other documentation provided. If you still have questions, contact us during business hours (Monday through Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time). Sales and support contact information North America Toll-free: 855.286.8889 in the US, including Alaska and Hawaii; Puerto Rico; Canada. Outside the toll-free area: 503.885.5700.
Copyright Trademarks and patents Manufacturer Certification ACMA compliance Canada European Union directives © 2011 UTC Fire & Security. All rights reserved. Interlogix and IFS names and logos are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. UTC Fire & Security Americas Corporation, Inc.
