Simon XT TableTop Control Panel Installation Manual P/N 466-2341 • REV C • OCT12
Copyright © 2012 UTC Fire & Security Americas Corporation, Inc. Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights reserved. This document may not be copied in whole or in part or otherwise reproduced without prior written consent from UTC Fire & Security except where specifically permitted under US and international copyright law. Document number: 466-2341 REV C (October 31, 2012 11:56 AM).
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Content Preface#ii Chapter 1 Introduction#1 Product overview#2 Chapter 2 Planning#7 Planning the installation#8 Emergency planning#19 Chapter 3 Installation#21 Panel connections#22 Hardwired device terminals#22 Telephone connections#24 Power transformer connection#26 Powering up the panel#27 X10 modules#28 Chapter 4 Programming#31 Programming overview#32 Menu navigation#34 System programming#37 Resetting memory to the factory defaults#56 Chapter 5 Testing#59 Control panel#60 Sensor testing#61 Phone communic
Preface This is the Simon XT TableTop Control Panel Installation Manual for model 6001054-95R-TT. This document includes an overview of the product and detailed instructions explaining: • • how to install; and how to set up the product for customer use. There is also information describing how to contact technical support if you have questions or concerns. To use this document effectively, you should have a basic knowledge of electrical wiring and low-voltage electrical connections.
Chapter 1 Introduction Summary This chapter provides an overview of the system and an outline of the steps you need to perform before you begin installing and configuring your security system.
Chapter 1: Product overview This security system can be used as a fire warning system, an intrusion alarm system, an emergency notification system, or any combination of the three. The system (Figure 1) has three types of components: • • • Self-contained control panel Devices that report to the panel Devices that respond to commands from the panel Figure 1: Simon XT TableTop Control Panel system Note: The universal, lamp, and appliance modules require a special transformer.
Chapter 1: System components The system can monitor up to 40 sensors and may use any of the devices listed in Table 1 Table 1: Supported devices Device Description Door/window sensor (60-670) For intrusion protection, install door/window sensors on all ground-floor doors and windows. At a minimum, install them in the following locations: • All easily accessible exterior doors and windows. • Interior doors leading into the garage. • Doors to areas containing valuables such as cabinets and closets.
Chapter 1: Device Description Carbon monoxide (CO) alarm (60652-95) The Learn Mode™ CO alarm alerts users to hazardous levels of carbon monoxide gas. If dangerous concentrations of gas are present, the red indicator light comes on, the internal siren goes off, and an alarm is transmitted to the panel. The panel sounds its own alarm and reports to the central station.
Chapter 1: Simon XT TableTop Control Panel Installation Manual 5
Chapter 2 Planning This chapter provides information to help you plan your installation to reduce time and costs.
Chapter 2: Planning the installation This section describes system capabilities to help you get familiar with your system. The planning sheets contain tables that let you record the hardware and programming configuration of your system. Complete all of the information ahead of time to help prepare for system installation. Refer to Sensor names on page 64 for sensor name segments listed alphabetically and by index number.
Chapter 2: Device Recommended sensor group Outdoor motion sensor 25 (chime only) Entry/exit door 10 Interior door 14 Window sensor 13 Smoke sensor 26 Keyfob 01, 03, 06, 07 ELM keyfob 01, 03, 06, 07 Remote handheld touchpad 01, 03, 06, 07 Simon XT TableTop Touchpad 01, 03, 06, 07 CO alarm 24 Freeze sensor 29 Water sensor 38 Personal help button 06, 07, 01, 03 Supervisor yry Restoral Delay Type Table 4: Sensor group characteristics Active in arming levels Name/application Si
Supervisor yry Restoral Delay Type Chapter 2: Active in arming levels Name/application Siren type 10 Entry/exit delay: A delay that requires a standard delay time. chime. Intrusion S Y Y 24 13 Instant perimeter: Exterior doors and windows. chime. Intrusion I Y Y 24 14 Instant interior: Interior doors. Intrusion F Y Y 234 15 Instant interior: Interior PIR motion sensors. Intrusion F Y Y 234 16 Instant interior: Interior doors.
Supervisor yry Restoral Delay Type Chapter 2: Active in arming levels Name/application Siren type 36 Special Intrusion: such as gun cabinets and wall safes. Reports as tamper if tripped. Intrusion I Y Y 1234 37 Light switch control: X10 modules turn either on or off when a door is opened. Silent I N Y 01234 38 Auxiliary: water sensors. Trouble beeps I Y Y 01234 39 Local instant interior: 24-hour local alarm zone protecting anything that opens and closes. No report.
Chapter 2: Sensor # Device Sensor group Sensor name/location Notes 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Cross-zoning Cross-zoning (two-trip) refers to two different group 18 sensors that must be tripped within two minutes of each other to report an alarm to the central station. Figure 2 shows the path of a person walking from the kitchen to the living room.
Chapter 2: Figure 2: Cross-zone diagram Note: We do not recommend cross-zoning for exit/entry zones. Each zone can individually protect the intended area. System configuration Table 6 is a worksheet for you to record the desired values for each programming option. For each option, the default value, effect of deletion (pressing Disarm while editing), range, and programming privilege are also listed. Each option is described in more detail in “Programming” on page 32.
Chapter 2: Function Default Delete Range Access a code User code 4 None None 3 to 6 digits D, I, M User code 5 None None 3 to 6 digits D, I, M User code 6 None None 3 to 6 digits D, I, M User code 7 None None 3 to 6 digits D, I, M User code 8 None None 3 to 6 digits D, I, M Duress code None None 3 to 6 digits D, I, M Code length 4 4 3 to 6 D Account number 00000 00000 0 to FFFFFFFFFF D, I Downloader code 12345 12345 00000 to 99999 D Phone lock Off Off On
Chapter 2: Function Default Delete Range Access a code DTMF On (Touchtone) Off (Pulse) On/Off D, I 300 bps baud rate On (300 bps) Off (110 bps) On/Off D, I Ring/hang/ring 1 Off 1 to 7, Off D, I Dial delay 30 seconds 15 sec. 15 to 45 sec.
Chapter 2: Function Default Delete Range Access a code Phone 1 report mode Off Off ALL SIA D Phone 2 report mode Off Off Phone 3 report mode Off Off Phone 4 report mode Off Off Nonalarms CID Backup SIA Backup CID Voice dialer Off D, I Latchkey time None None 12:00 midnight to 11:59 PM, None D, I, M Entry delay 30 sec. 30 sec. 30 to 240 sec. D, I Exit delay 60 Seconds 45 sec. 45 to 254 sec.
Chapter 2: Function Default Delete Range Access a code Installer settings Touchpad options menu Keyfob no delay Off Off On/Off D, I Panic alarms On Off On/Off D, I Remote touchpad arming Off Off On/Off D, I System options menu RF Jam detect Off Off On/Off D, I Demo mode Off Off On/Off D, I HW1 function 1 Off 1 - Interior siren output 2 - Output activated when armed 3 - Output activated when disarmed 4 - FTC output (FTC must be on) 5 - Output activated for alarm Off - No ou
Chapter 2: Function Default Delete Range Access a code Speaker volume 8 8 1 to 8 D, I, M Panel silent police panic Off Off On (silent), Off (audible) D, I Panel tamper alarm Off Off On/Off D, I Alarm report verification Off Off On/Off D, I Installer settings Audio verify menu Audio mode Off Off Off - Audio mode disabled 1 - Instant mode 2 - Callback mode D, I Fire shutdown Off Off On/Off D, I Panic talk Off Off On/Off D, I Vox receiver gain 6 6 1 to 32 D, I Vox
Chapter 2: Function Default Delete Range Access a code Installer settings a This column tells what type of access code is allowed to make changes D = Dealer code I = Installer code M = Master code Emergency planning Use these guidelines when drawing an emergency floor plan for the homeowner: • • • • Show all building levels. Show exits from each room. (We recommend two exits per room.) Show the locations of all security system components. Show the locations of any fire extinguishers.
Chapter 3 Installation This section describes how to connect hardwired devices, and the AC power transformer.
Chapter 3: Panel connections The panel has three screw terminals, two telephone connections, and a 9 VAC plug (Figure 3). Figure 3: Simon XT TableTop Control Panel terminal connections Hardwired device terminals The screw terminals connect sirens, and/or hardwired detectors. Program sensors and devices before you install them. Follow the instructions in Sensors on page 35 to add the sensors to panel memory.
Chapter 3: Note: The total current available from HW1&2 DC Out is 250 mA at up to 120°F (49°C). With Hardwired Siren Supervision turned on, sirens connected to HW1 I/O are supervised and require a 4.7 kohm resistor in the circuit. If this terminal is not used, turn Hardwired Siren Supervision off. LD105 hardwired interior siren You must always wire interior sirens with a resistor in the circuit.
Chapter 3: Connect hardwired reed switches to the panel using a 47 kohm resistor (not a 4.7 kohm resistor) as shown in Figure 5. The resistor must be connected at the last switch in the circuit. Do not install the resistor at the panel terminals. This does not provide supervision of the wire.
Chapter 3: 2. Connect the four-conductor cable wires to the RJ31X. 3. Disconnect the green and red premises phone jack wires from the Telco block and splice them to the four-conductor cable black and white (or yellow) wires. Use weatherproof wire connectors for these splices. 4. Connect the four-conductor cable green and red wires to the Telco block TIP (+) and red to RING (–) posts. 5. Connect the phone cord included with the panel to the RJ31X and the panel LINE jack.
Chapter 3: 2. Connect the included phone cord to the panel LINE jack and the premises phone jack. Note: If customers add phones or other phone devices to another phone jack, full line seizure no longer exists. Inform them to contact you if they want to add a phone or other device so that you can rewire for full line seizure by adding an RJ31X.
Chapter 3: Figure 8: Transformer connections Note: Do not plug in the transformer at this time Powering up the panel When applying power to the panel, first connect the backup battery, then plug in the AC power transformer. This sequence prevents a battery fault condition. Maximum battery charge current is 45 mA. It may take up to 24 hours for a new battery to fully charge. Backup battery To connect the backup battery (6 VDC, 1.2 Ah), do the following: 1.
Chapter 3: Applying AC power To apply AC power, do the following: 1. Make sure the outlet is not controlled by a switch or that it is not part of a ground fault circuit interrupt (GFCI). 2. Remove the center screw from the outlet cover plate and hold the cover plate in place. WARNING: Use extreme caution when securing the transformer to a metal outlet cover. You could receive a serious shock if a metal cover drops down onto the prongs of the plug. 3.
Chapter 3: 9 - Sirens with this setting sound alarms, arming level beeps, status beeps, and trouble beeps. 10 - Sirens with this setting only sound alarms. 2. Set the powerhorn house code to one above the panel house code. 3. Plug the powerhorn module into a wall outlet.
Chapter 4 Programming This chapter provides steps on how to program your unit.
Chapter 4: Programming overview The control panel (Figure 9 below) provides the main processing unit for all system functions. System options and features programming is menu-driven. All installer options are set in the System programming menu, except for setting the system time. Table 7 below explains the panel keys and features.
Chapter 4: Control Description LCD display The LCD module has a 2 x 16 character array that displays a variety of phrases and icons. Doors+Windows Press to arm perimeter sensors. Motions Press to arm interior sensors. Disarm Press to turn off intrusion/burglary protection for your system. Only intrusion/burglary sensors such as doors, windows, and motion sensors are disarmed. Environmental sensors, such as smoke and carbon monoxide, stay active at all times.
Chapter 4: of inactivity if no access code has been entered yet. After an access code has been entered to access a code-protected area of the system menu, the timeout is four minutes. Menu navigation Each menu contains a list of options and/or submenus. Press the scroll up/down buttons to navigate up and down the list of options and submenus in that menu. Pressing Enter after navigating to an option selects that option for editing and flashes the current value.
Chapter 4: Master code Phone #2 User code 1 Phone #3 User code 2 Phone #4 User code 3 Downloader phone number User code 4 Phone options User code 5 Manual phone test User code 6 Fail to communicate User code 7 DTMF dialing User code 8 300 bps baud rate Duress code Ring/hang/ring Code length Dialer delay Call waiting code Sensors System options Learn sensor RF jam detect Delete sensor Demo mode Edit sensor HW1 I/O Reporting Report options 24-hour clock format Siren options Op
Chapter 4: Phone 3 reports Vox receiver gain Phone 4 reports Vox microphone gain Timers Vox gain range Latchkey time Manual microphone gain Entry delay Light control Exit delay Set entry lights No activity timeout Sensor lights Auto phone test Light schedules Supervisory time Housecode Alarm cancel window Lock interval RF timeout System tests Fail to open time Sensor test Fail to close time Communication test Siren timeout Initiate download call Arming LEDs shutdown Revision U
Chapter 4: 2. The display shows Enter code. Enter your code with numeric keys. Press Enter. 3. Press Enter. 4. The display now flashes the hours. Scroll up/down to set the hours. Press Enter to accept. 5. The display now flashes the minutes. Scroll up/down to set the minutes. Press Enter to accept. 6. The display now flashes the AM/PM. Scroll up/down to set the AM/PM. Press Enter to accept. 7. The display now shows the current time, and stops flashing. Press Status twice to exit.
Chapter 4: 3. The system displays each entered access code digit as an asterisk. Press Enter. The panel is now in program mode. Note: Do not remove panel power while in program mode. Table 9: Simon XT TableTop Control Panel programming codes Code Description Dealer code You can use the dealer code to program all system options, including high-security options that are not accessible with the installer code if it is different from the dealer code.
Chapter 4: Security Table 11 provides security option details. Table 11: Security Function Default Description Account number 00000 Lets you program up to a 10-character alphanumeric account number or delete an existing account number by pressing Disarm. You can enter numerical digits sequentially. To enter letters (A to F only), use the scroll buttons to select A to F then press Enter. To select next digit, press another number key. When finished press Enter.
Chapter 4: Function Default Description Autoarm On Determines how long the system protests (announces open/failed sensors) when attempting to arm with open/failed sensors , before bypassing these sensors and automatically arming the rest of the system. The panel protests an arming attempt when it has not received a restore (close) signal from sensors learned into restore-specific sensors groups. Sensors learned into group 26 (fire) cannot be bypassed.
Chapter 4: Function Default Description Sup protest Off Determines whether the panel protests arming if it has not received a supervisory signal from any sensor 15 minutes before arming (on) or not (off). Note: This feature must be turned off for US installations. Phone numbers Table 12 below provides phone number option details.
Chapter 4: Function Default Description Ring hang ring 1 Determines when the panel answers a remote phone access or Enterprise call. Depending on whether an answering machine exists at the panel location, offsite access to the panel can be done with a series of phone calls or just one. For offsite access where an answering machine does not exist, the user or Enterprise operator simply calls the panel location once and listens for 10 rings. The panel should answer after the tenth ring.
Chapter 4: Sensors These instructions explain how to add (learn) sensors, touchpads, and other system devices into panel memory. The panel recognizes a sensor when you press a sensor program button, press and release a tamper switch, press a sensor test button, or put a sensor into alarm. Table 14 below describes the programming method for each device.
Chapter 4: When learning sensors, the panel uses an ascending number sequence starting with 1. You can override this by entering the desired sensor number using the number keys. Adding (learning) sensors To add (learn) a sensor, do the following: 1. Press the scroll buttons until the panel displays System programming. Press Enter. 2. The system prompts for an access code. Enter the dealer or installer code. Press Enter. 3. The panel displays Access codes.
Chapter 4: 5. The panel displays Sn ## Grp ## . Press the scroll buttons until the panel displays the sensor you want to delete. Press Enter. 6. The panel displays Deleted, then shows Delete sensor. Press Status twice to exit. Editing sensors You can use this feature to change the group or name of a sensor that is already in panel memory. The procedure is very similar to the procedure used to program sensor information after a sensor is learned in.
Chapter 4: Function Default Description Closing reports Off Determines whether the panel sends closing reports to a central station whenever the system is armed (on), or not (off). User number will be reported as zone number. Keyfobs learned into zones 1 through 40 will report as the zone they are learned into.
Chapter 4: Function Default Description No usage Off Determines whether the panel sends a no usage report to the central station if the user has not operated the system before the programmed time expires (on) or not (off). The timer starts each time the system is disarmed. This is a customer service feature that alerts the central station if a customer is not using their security system.
Chapter 4: Timers Table 18 below provides timer option details. Table 18: Timers Function Default Description Latchkey time Off Determines whether the panel reports a latchkey alarm if the system is not disarmed at a preset time between midnight and 11:59 p.m. (on). If the latchkey feature is disabled (off), the panel will not report a latchkey alarm. The system clock must be set for the latchkey feature to work.
Chapter 4: Function Default Description RF timeout 12 hours Determines the time period the panel must receive at least one supervisory signal from learned sensors before identifying a sensor failure and sounding trouble beeps. Any sensor failure is reported immediately and again at the supervisory time. The timeout can be set from 02 to 36 hours. Entries must be two digits.
Chapter 4: Function Default Description Panic alarms On Determines whether the panel panic buttons (police, auxiliary, and fire) activate alarms when pressed (on) or not (off) Remote TP arm Off Determines whether keyfobs and remote touchpads can disarm the system only during exit and entry delays (on) or arm and disarm the system anytime (off). If this option and Keyfob no delay are on, users cannot enter and/or disarm using remote touchpads without causing an alarm.
Chapter 4: Table 21: Siren options Function Default Description Piezo beeps On This option determines whether the panel piezo produces beeps based on system activity (on) or is silent (off). Panel voice On When on, arming level changes will be spoken. Panel piezo alarm On Determines whether the panel piezo emits alarm sounds (on) or not (off).
Chapter 4: Function Default Description Alarm report verify Off This option determines whether the panel verifies successful alarm reports to the central station by displaying Phone comm is OK (on), or not (off). Piezo beep options Table 22 below provides piezo beep option details. Table 22: Panel piezo beeps Activity Piezo beep response Arm doors and windows Exit delay—two beeps sound every five seconds and two times per second during the last ten seconds.
Chapter 4: Table 23: Audio verification Function Default Description Audio mode Off 1 = Instant. Panel stays online with central station for an instant audio session. 2 = Callback. Panel hangs up and waits for a callback from the central station operator before starting an audio session. Off = No audio verification. Fire shutdown Off Determines whether system fire sirens are silenced during a two-way audio session (on) or not (off). Beeps sound every 10 seconds while sirens are silenced.
Chapter 4: To program the housecode, do the following: 1. Press the scroll buttons until the panel displays System programming. Press Enter. 2. The panel displays Enter code. Enter your access code and press Enter. 3. The panel displays Access codes. Press the scroll buttons until the panel displays Light control. Press Enter. 4. The panel displays Set entry lights. Press the scroll buttons until the panel displays Housecode . Press Enter. 5. The letter flashes.
Chapter 4: 6. The panel displays On/off, which will be flashing. Press the scroll buttons until the panel displays On. Press Enter. 7. Press Status three times to exit. Note: You can also program a keyfob button to control a light or appliance module. To program a light schedule, do the following: 1. Press the scroll buttons until the panel displays System programming. Press Enter. 2. The panel displays Enter code. Enter your access code and press Enter. 3. The panel displays Access codes.
Chapter 4: Table 24 below provides light control option details. Table 24: Light control Function Set entry lights: Entry light unit, 1 through 8 Default Description Off This menu allows the user to set X-10 lights with unit numbers from 1 to 8 as entry lights (on). Sensor light # 01 to 40 Light schedules Light schedule, 1 through 8 Housecode Lock interval In this menu, each enrolled sensor can be associated with an X-10 light with unit number from 1 to 8 (or Off for no association).
Chapter 4: 6. Power up the panel with the battery and then the AC transformer. Note: The procedure to reset memory to factory defaults is meant to be difficult. To program the panel, do the following: 1. Set the panel clock. 2. Add (learn) sensors. 3. Set the housecode and light and appliance controls (entry/exit activated lights, sensor-activated lights, time-activated lights). 4. Change options as needed.
Chapter 5 Testing This section describes how to perform various test procedures. You should test the system after installing, after servicing, and after adding or removing devices from the system.
Chapter 5: Control panel Test the panel by pressing the buttons as described in Table 26 below and Table 27 on page 61 provides a list of the arming levels. Note: An access code is required when arming if the Secure arming option is on Table 26: Control panel test sequence Button Function tested Test Correct result Doors+Windows The panel arms door and window sensors. Press Doors+Windows a second time to eliminate the programmed entry delay. The button will blink when no entry delay is on.
Chapter 5: Table 27: Arming levels Arming level Description Indication 0 Subdisarms (master access and duress codes only), and bypasses 24hour intrusion sensors (master access code only). Fire sensors (group 26) cannot be subdisarmed. One beep indicates the system is subdisarmed. The panel displays and speaks Subdisarmed. The Disarm button blinks. 1 Disarm the system One beep indicates the system is disarmed. The panel displays and speaks Disarmed. The Disarm button lights.
Chapter 5: Table 28: Sensor tripping instructions Sensor Do this Door/window Open the secured door or window. Freeze Remove the sensor cover. Apply ice in a plastic bag to the sensor (for 10 to 15 minutes). Do not allow the sensor to get wet. Water Press a wet rag or wet finger over both of the round, gold-plated terminals on the underside of the sensor. Carbon monoxide alarm Unplug the CO Alarm. Plug it back in, wait 5 seconds, then press the TEST/RESET button until the unit beeps 8 times.
Chapter 5: Type of sensor Number of beeps Wireless smoke and heat sensors 7 to 8 Wireless environmental/panic buttons 7 to 8 Hardwired loops 1 Emergency buttons (remote handheld touchpads only) 7 to 8 4. Press Status. The panel displays Sensor test OK. If you press Status and the panel has not heard from all sensors, the panel will display Sn test fail or aborted.
Chapter 5: 3. If the known-good sensor functions, contact UTC Fire and Security for repair or replacement of the problem sensor. Phone communication Perform a communication test to check the phone communication between the panel and the central station. To perform a communication test, do the following: 1. Go to the Comm test option under the System tests menu. 2. Press Enter. The panel confirms that a communication test has begun.
Chapter 5: System Function Phone command Specific light off # – . All lights on *–* All lights off #–# System status 0 Audio verification 5 + X (X = a command from Audio Verification Set) Terminate session 9 Central station communication After performing sensor and communication tests, check that the system is reporting alarms successfully to the central station. Table 31 below provides a list of sensor/user report codes.
Chapter 5: Arm or disarm from Reports as user Access codes 1 to 8 47 to 54 Duress code 55 Two-way voice operation For the central station operator to initiate an audio session, see Table 32 below and do the following: 1. After the panel has completed reporting the alarm, pick up the CS phone and press the * button to start the audio session. 2. Press 1 or 0 to speak, 2 for vox operation, and 3 or 6 to listen. 3. Press 99 to terminate the session.
Chapter 5: 4. Press * and the panel voice identifies the alarm. If there is more than one alarm in progress, the user must press * for the panel voice to identify them. Note: You must terminate the call by pressing #. Otherwise, the panel may not disconnect from the phone line for up to 2 minutes. 5. After all alarms have been identified, the panel announces Press # to exit. 6. Press # to terminate the call.
Chapter 5: X10 siren and lamp module functions All sirens turn off when the system is disarmed or when the siren timeout expires. Siren priority is fire (highest priority), intrusion, and emergency. Table 33 below identifies the light information for each of these siren types.
Chapter 6 Troubleshoot and support This chapter provides information to help you troubleshoot problems and contact technical support in case you need assistance with your UTC Fire & Security equipment.
Chapter 6: Troubleshooting This section provides information to help you diagnose and solve various problems that may arise while configuring or using your UTC Fire & Security product and offers technical support contacts in case you need assistance. (See “Contacting us” on page 72.) System status • How do I clear Status (alarm memory)? From a disarmed state press Status, listen to the status message, then press Disarm. • The panel displays and announces Siren 1 failure.
Chapter 6: Latchkey is not enabled. Enable latchkey by pressing Motions twice. The phone number is not programmed properly. Reprogram the phone number. System time is not set. Set system time. Sensors • A sensor does not work. Make sure the battery is good and installed correctly. Check for interference from metal objects. Move or rotate the sensor. • Door or window is closed, but the panel announces it is open.
Chapter 6: Unplug nearby equipment that may be causing interference (light dimmer switches, televisions, appliances with older motors). Check that the switch on the lamp or appliance is turned on and remains on. Make sure the lamp has a working bulb. Make sure the lamp or appliance is plugged into the lamp/appliance module, the module is plugged into the outlet and the outlet is not controlled by a switch. Make sure the housecode and unit code are correct.
Appendix A Specifications and tables This appendix provides lists of sensor names and a quick reference chart for operating the Simon XT TableTop system with various peripheral devices.
Appendix A: Specifications Table 35: Simon XT TableTop Control Panel specifications Requirement Description Power 9 VAC, 60 Hz, 25 VA transformer (minimum) Rechargeable battery: 6.0 VDC, 1.2 Ah lead-acid. The battery will last 24 hours with no AC and specified standby load of 250 mA. Maximum battery charging current is 45 mA. With loss of AC panel will continue to operate normally to a minimum of 5.1 VDC. Radio frequency 319.
Appendix A: Function Programming page reference Default setting Required setting Autoarm Table 11 on page 39 On On Unvacated premises Table 18 on page 48 On On Call waiting Table 13 on page 41 Off On if reporting to central station and customer has call waiting service Exit extension Table 11 on page 39 On On Swinger shutdown Table 16 on page 45 On (one trip) On (one trip) Fire alarm verify Table 16 on page 45 Off On Duress/panic code Table 10 on page 38 Disabled Disabled Cr
Appendix A: Central station reporting The panel has been tested with the following central station receivers using SIA and Contact ID reporting formats: • • • Radionics D6600 central station receiver Sur-Gard central station receiver with models SG-DRL2A and SG-CPM2 CS5000 digital alarm communicator receiver Before beginning installation, installers must verify compatibility with the central station receiver.
Appendix A: # Phrase # Phrase 130 Family room 041 Module 142 Fire 024 Office # Phrase Table 39: Sensor name segments by index number (in scrolling order) # Phrase # Phrase # Phrase 000 Keyfob (keychain) 049 G 098 .
Appendix A: # Phrase # Phrase # Phrase 028 Garage 077 8 126 x 029 Special chime 078 9 127 y 030 Basement 079 / 128 z 031 Basement window 080 ‘ 129 Dining room 032 Upstairs 081 ! 130 Family room 033 Upstairs window 082 @ 131 Laundry 034 Downstairs 083 # 132 Sliding door 035 Downstairs window 084 $ 133 Patio 036 Hallway 085 % 134 Pool 037 Medicine cabinet 086 & 135 Window 038 Closet 087 * 136 Door 039 Attic 088 ( 137 Baby 040 Syst
Appendix A: :Simon XT TableTop System quick reference Simon XT TableTop Control Panel Installation Manual 79
