Data Sheet

ManualsBrandsInterlogix ManualsAccessories communicationPOE302-EX

IFS

Line / Network Transmission

interlogix.com

POE302-EX

IEEE 802.3af/at

PoE+ and Ethernet Data Extender

OVERVIEW

The IFS

Power over Ethernet Extender is a quick and easy solution

that can be used when a Powered Device (PD) needs to be installed

beyond the 100 meter (328 ft.) distance limitation of Ethernet. The

module can be powered from any network switch with PoE or from

an IFS Mid-Span Power Injector.

This module provides the ability to extend Ethernet data and PoE

power on a single network cable for remote deployment of an

Ethernet powered device (PD) i.e. IP camera, access control panel,

VoIP or wireless access point (WAP).

The IFS POE302-EX is powered via the PoE power provided by a

PoE switch or injector and thus does not require an external power

adapter. Each extender requires 3.2 watts of PoE power providing

the remaining power to the next extender or PD device.

Up to three POE302-EX extenders can be daisy-chained at

328 ft. (100m) intervals, based on the EIA-568 standard, to extend

Ethernet data and PoE power up to 984 ft. (300m). Maximum

distance (or hops) is dependent upon the remaining PoE power

available to meet the PD power requirements.

The POE302-EX facilitates easier network planning by eliminating

restrictions of edge device placement near AC power outlets

and reducing the need for AC wiring and installation costs while

delivering higher reliability. This results in a cost-effective remote

power and data distribution cable management solution for a

PoE-centric IP network.

STANDARD FEATURES

Installation

• Compact size

• Plug-and-play PoE self-powered design

• Standalone or wall-mount installation

• Can be used with an IFS PoE Injector or other

IEEE 802.3af or 802.3at compliant PSE equipment

Standards Compliance

• Supports 10/100/1000Base-TX Ethernet

• Complies with IEEE 802.3/802.3u/802.3ab

• Complies with IEEE 802.3af or 802.3at PoE Standard

PoE Circuit

• Auto-detect of PoE IEEE 802.3af or 802.3at equipment

providing protection from incorrect installation

• Current overload detection

• LED Indicators for PoE In, PoE Out, Data

• Requires 3.2 watts of PoE power to operate

Physical Ports

• One RJ45 port for data with PoE In

• One RJ45 connector for data with PoE Power Out

Network Cable

• For use with EIA568 Category 5 or better cables

• Can be daisy-chained to extend data and PoE on a single

network cable a maximum of 984 ft. (300m).

Warranty

• 3-year warranty

Summary of content (3 pages)

PAGE 1
IFS® Line / Network Transmission POE302-EX IEEE 802.3af/at PoE+ and Ethernet Data Extender OVERVIEW STANDARD FEATURES The IFS® Power over Ethernet Extender is a quick and easy solution that can be used when a Powered Device (PD) needs to be installed beyond the 100 meter (328 ft.) distance limitation of Ethernet. The module can be powered from any network switch with PoE or from an IFS Mid-Span Power Injector.
PAGE 2
Speciﬁcations Ethernet Description Data Rate 10/100/1000Mbps Throughput (packet per second) 14.8Mpps@64Bytes IEEE Standards IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet IEEE 802.3ab Gigabit Ethernet IEEE 802.3x Flow Control Latency 4.285 Maximum Frame Size 9K Bytes EIA/TIA-568 Standards Category 5 or better Power Over Ethernet (PoE) PoE Standard IEEE 802.3af or IEEE 802.
PAGE 3
North America T 855-286-8889 POE302-EX IEEE 802.3af/at Latin America T 561-998-6114 PoE+ and Ethernet Data Extender Ordering Information POE302-EX IEEE 802.3at (30w) Power over Ethernet Extender (mid-span) Note: No power adapter required. Unit is powered via PoE from a PoE switch or PoE Injector. Dimensional Diagrams POE302-EX Gigabit Ethernet PoE-AT Extender IN 2.76 in. (70.3mm) OUT Ethernet+DC OUT IN E Po 1.03 in. (26.2mm) T T IN E OU K/AC Po LN 3.70 in. (94mm) interlogix.