IFS POE201-MS/4 4-Port PoE-af Injector User Manual P/N 1072580 • REV R00.
Copyright © 2013 UTC Fire & Security Americas Corporation, Inc. Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights reserved. Trademarks and patents Intended use Manufacturer The IFS POE201-MS/4 4-Port PoE-af Injector and logo are trademarks of United Technologies. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Contents Package Contents 1 Product Features 1 Product Overview 3 LED Indicators 4 Hardware Installation 4 Before Installation 4 Injector Installation 4 Troubleshooting 6 Appendix A: Network Connection 7 RJ-45 Pin Assignments 7 Specifications 9 Contacting Technical Support 10 IFS POE201-MS/4 4-Port PoE-af Injector User Manual i
Package Contents Thank you for purchasing the IFS POE201-MS/4, an IEEE 802.3af High Power over Ethernet Injector Hub. Open the package containing the Ethernet Injector Hub and carefully unpack it. The box should contain the following items: ● POE201-MS/4 x1 ● User Manual x1 If any of these items are missing or damaged, please contact your distributor or IFS Sales Rep.
• Full power support (15.
Product Overview Figure 1 shows the front and side panels of the POE201-MS/4.
LED Indicators POE201-MS/4 LED indicators LED Color PWR Green PoE In-use Green Function Lit indicates that the POE201-MS/4 has power. Lit indicates that the PoE port is providing 56VDC in-line power. Hardware Installation This product provides two different running speeds – 10Mbps and 100Mbps- in the same device and automatically distinguishes the speed of the incoming connection. This section describes the hardware features of the POE201MS/4.
Ethernet devices such as an IFS IEEE 802.3af Power over Ethernet Splitter (SP-POE) for non-PoE devices. The POE201-MS/4 can be directly deployed to connect the third party IEEE 802.3af devices installed 100 meters away. Figure 2: Connection Architecture Note: According to the IEEE 802.3af standard, the POE201MS/4 will not inject power to the cable if it is not connected to IEEE 802.3af devices.
Troubleshooting This chapter contains information to help you solve problems. If the POE201-MS/4 is not functioning properly, make sure the POE201-MS/4 is set up according to instructions in this manual. How can my non IEEE 802.3af network devices can work with the POE201-MS/4? Solution: You can use IFS Power over Ethernet Splitter, such as the IFS SP-POE to work as a power transformer between the POE201-MS/4 and non-IEEE 802.3af devices.
Appendix A: Network Connection RJ-45 Pin Assignments 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment Contact 1 2 3 4, 5 6 7, 8 MDI MDI-X Media Dependant Media Dependant Interface Interface -Cross Tx + (transmit) Rx + (receive) Tx - (transmit) Rx - (receive) Rx + (receive) Tx + (transmit) IEEE 802.3af DC 48V Rx - (receive) Tx - (transmit) IEEE 802.3af DC 0V The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
Please make sure that the cables used are with same pin assignment and color as above picture before deploying the cables into your network. Energy Saving Note of the Device This power required device does not support standby mode operation. For energy saving, please remove the power cable to disconnect the device from the power circuit. Without removing the power cable, the device will still consume power from the power source.
Specifications Model Ethernet Connector POE201-MS/4 Ethernet Data Rate 10/100Mbps( vary on Ethernet device attached) Input Voltage DC 48V, 1.5A Number of Device can be Powered 4 Ethernet Cable TIA/EIA-568, Category 5/5e cable LED Indicator 1 x power, 4 x POE ready / in-use Operating Environment 0~50 Degree C, 5%~90%RH Storage Environment -10~70 Degree C, 5%~90%RH Dimension (H x W x D) 26 x 70 x 97mm Weight 220g Emission FCC Class B, CE mark Standard Compliance IEEE 802.
Contacting Technical Support Contact technical support if you encounter any difficulties during this installation. Please contact us by phone or go to www.interlogix.com/customer-support. Technical Support Europe, Middle East and Africa W Select Contact Us at www.utcfssecurityproducts.eu North America T +1 855.286.8889 E techsupport@interlogix.com Australia E 10 techsupport@interlogix.
