POC2052-4P-1CX PoE Over Coaxial Extender User Manual P/N 1073393-EN • REV A • ISS 27FEB18
Copyright Trademarks and patents Manufacturer Version © 2018 United Technologies Corporation. Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. All rights reserved. Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Interlogix 2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA Authorized EU manufacturing representative: UTC Fire & Security B.V.
Content Important information 2 Chapter 1 Introduction 3 Package contents 3 Chapter 2 Hardware description 4 Physical dimensions 4 Front panel 4 LED indicators 5 Product specifications 7 Chapter 3 Installation 11 Installation precautions 11 Chapter 4 Application diagram 14 Point to multi-point 14 Multi-point to multi-point 16 Applications of POC252-1CXP-1T or POC switch with coaxial cable 17 Appendix A Networking connection 21 POC2052-4P-1CX PoE Over Coaxial Extender User Manual 1
Important information Limitation of liability To the maximum extent permitted by applicable law, in no event will UTCFS be liable for any lost profits or business opportunities, loss of use, business interruption, loss of data, or any other indirect, special, incidental, or consequential damages under any theory of liability, whether based in contract, tort, negligence, product liability, or otherwise.
Chapter 1 Introduction The description of the IFS POC2052-4P-1CX model is as follows: 4-port 10/100TX PoE Extender Unless specified, the term “POC extender” mentioned in this user manual refers to the POC2052-4P-1CX. Package contents Open the box of the industrial PoE+ switch and carefully unpack it. The box should contain the following items: The POC extender × 1 DIN rail kit x 1 Wall mounting kit x 1 If any of these are missing or damaged, contact your dealer immediately.
Chapter 2 Hardware description Physical dimensions Dimensions (W x D x H): 135 x 87.8 x 56 mm Front panel The front panel of the POC extender consists of 1BNC female/RJ45 connector and four 10/100BASE-TX RJ45 ports. The LED indicators are also located on the RJ45 ports of POC extender.
Chapter 2: Hardware description LED indicators External power supply LED Color Function P1 Green Lit: indicates that the power input 1 has power. P2 Green Lit: indicates that the power input 2 has power. Fault Red Lit: indicates that either power 1 or power 2 has no power. LED Color Function 10 W Green Lit: indicates the power usage is ≧ 10 W. 20 W Green Lit: indicates the power usage is ≧ 20 W. 30 W Green Lit: indicates the power usage is ≧ 30 W.
Chapter 2: Hardware description 40 W Green Lit: indicates the power usage is ≧ 40 W. Color Function Green Lit: indicates the port has successfully connected to the network at 10/100/1000 Mbps. POC interface LED LNK/ACT 1000 Blinking: indicates that the switch is actively sending or receiving data over that port. Orange Lit: indicates the port has successfully connected to the network at 1000 Mbps.
Chapter 2: Hardware description Port 1 Port 2 Port 3 Port 4 ON (default) Port-1 PoE Enable OFF Port-1 PoE Disable ON (default) Port-2 PoE Enable OFF Port-2 PoE Disable ON (default) Port-3 PoE Enable OFF Port-3 PoE Disable ON (default) Port-4 PoE Enable OFF Port-4 PoE Disable Note: For example, to stop the remote powered device of port 1, turn the switch OFF to stop the output power.
Chapter 2: Hardware description Maximum Distance 100 m Maximum Frame size 1522 bytes One BNC female Connectivity Long Reach PoE over Coaxial PD (Powered Device) Power Input 44~ 56 VDC Power Pin Assignment BNC center pole: DC+ BNC shield: DCCoaxial cable: 75 ohm Cabling RG-6/U cable, less than12Ω/1000 ft RG-59/U cable, less than 30Ω/1000 ft. Max. 200 m with PoE+ output (656 ft.) Long Reach PoE Maximum Distance Interface Max. 400 m with PoE output (1,312 ft.) Max.
Chapter 2: Hardware description Power Requirements 44~56 VDC power over coaxial input DC 24~48 V, redundant power with polarity reverses protection function Power Consumption/ Dissipation 130 W/446BTU (Ethernet with PoE Full Loading) Alarm One relay output for power failure. Alarm relay current carry ability: 1A @ 24 VDC Enclosure Aluminum metal case Standards Conformance IEEE 802.3 Ethernet/10BASE-T Standards Compliance IEEE 802.3u Fast Ethernet/100BASE-TX IEEE 802.
Chapter 2: Hardware description RG-59 bare copper coaxial cable specs Item No. Cable Length (FT.) 1 Maximum PoE Output (W) From POC252-1CXP-1T POC2502-16CXP-1T-2S 200 22.0 22.0 2 400 22.0 22.0 3 600 22.1 22.0 4 800 21.1 21.1 5 1000 20.2 20.1 6 1200 19.3 19.1 7 1400 18.9 18.1 8 1600 17.4 16.9 9 1800 16.8 15.7 10 2000 15.6 14.4 11 2200 14.4 13.8 12 2400 12.9 12.7 13 2600 12.3 11.4 14 2800 11.7 10.6 15 3000 9.6 9.6 16 3300 8.6 8.
Chapter 3 Installation This section describes the installation and functionalities of the POC extender’s components. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. Note: Before installation, consider the distance and Watt value demand for PD devices. The POC extender output capacity and upload/download performance depends on the length of the coaxial and UTP cables.
Chapter 3: Installation Note: Interlogix IFS power over coaxial injectors or switches have a warning sticker, including the POC252-1CXP-1T and POC2502-8CXP-2T products. Remote power by UTP cable When installing the POC PoE over UTP injector, it only can work withthe POC extender. Please confirm that other non-PoE equipment is not connected with the UTP cable. If it is connected with the standard Ethernet equipment, it might cause damage.
Chapter 3: Installation 1 2 Power 1 + 3 4 Fault 5 6 Power 2 + Note: 1. The wire gauge for the terminal block should be in the range of 12 to 24 AWG. 2. The DC power input range is 24 to 48 VDC. Wiring the fault alarm contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the POC extender detects the fault status of the power failure and then forms an open circuit.
Chapter 4 Application diagram The POC extender is designed to extend IP Ethernet transmission and inject power simultaneously into a remote 802.3af/at PoE compliant powered device (PD) beyond the 100 meters distance limit of Ethernet. The solution works in pairs for point to point and point to multipoint connectivity. The POC extender supports two ways for a power source to inject 802.3af/at PoE to remote standard PDs. • Remote POC power from the POC injector/switch over coaxial cable.
Chapter 4: Application diagram POC252-1CXP-1T to POC2052-4P-1CX POC2052-4P-1CX PoE Over Coaxial Extender User Manual 15
Chapter 4: Application diagram Multi-point to multi-point Remote power POC power through BNC with DC 56 V input or local power with wxternal DC input (DC 24~48 V).
Chapter 4: Application diagram Applications of POC252-1CXP-1T or POC switch with coaxial cable One POC252-1CXP-1T with PoE power input and one POC2052-4P-1CX with PoE power output The POC injector is powered via IEEE 802.3at/af PoE. An IEEE 802.3at/af compliant PoE PD will automatically be powered by the POC extender via UTP. Functions POC252-1CXP-1T POC injector POC2052-4P-1CX POC extender Power Input RJ45 with 802.
Chapter 4: Application diagram One POC252-1CXP-1T with 48 to 56 V power adapter and one POC2052-4P-1CX with PoE power output The POC injector is powered via the external adapter. The IEEE 802.3at/af compliant PoE PD will automatically be powered by the POC extender via UTP. Functions POC252-1CXP-1T POC injector POC2052-4P-1CX POC extender Power adapter with 48~56V DC in.
Chapter 4: Application diagram 2. The POC252-1CXP-1T has two power input options; only one mode is available at one time. PoE power input cannot be used if power input of DC 52 V or 56 V is selected. One POC2502-8CXP-2T-2S with AC power input and one POC extender with PoE power output The POC switch is powered via the AC power. The IEEE 802.3at/af compliant PoE PD will automatically be powered by the POC extender via UTP.
Chapter 4: Application diagram 4. After enabling the POC function of the POC switch from the WebUI, the PWR LED of POC2052-4P-1CX should illuminate immediately. 5. Connect a Cat5/6 UTP cable to the POC extender and an IEEE 802.3at/af compliant PoE IP camera or PoE wireless AP. Note: 1. PoE output capacity is based on different DC power input / PoE input. 2. The POC252-1CXP-1T has two power input options; only one mode is available at one time.
Appendix A Networking connection RJ45 pin assignments 10/100Mbps, 10/100BASE-TX Pin number MDI MDI-X PoE 1 Tx + (transmit) Rx + (receive) Positive (VCC+) 2 Tx - (transmit) Rx - (receive) Positive (VCC+) 3 Rx + (receive) Tx + (transmit) Negative (VCC-) 4, 5 6 Not used Rx + (receive) 7, 8 Tx + (transmit) Not used Not used Negative (VCC-) Not used RJ45 cable pin assignments The standard RJ45 receptacle/connector: There are eight wires on a standard UTP/STP cable and each wire is color-cod
Straight Cable 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 SIDE 1 SIDE 2 Crossover Cable 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 SIDE 1 SIDE 2 SIDE 1 SIDE 2 1 = White / Orange 1 = White / Orange 2 = Orange 2 = Orange 3 = White / Green 3 = White / Green 4 = Blue 4 = Blue 5 = White / Blue 5 = White / Blue 6 = Green 6 = Green 7 = White / Brown 7 = White / Brown 8 = Brown 8 = Brown SIDE 1 SIDE 2 1 = White / Orange 1 = White / Green 2 = Orange 2 = Green 3 = White / Green
