Installation Manual

ManualsBrandsInterlogix ManualsAlarms AccessoriesAES Long Range Radio Interface Module

NX-582E

AES RADIO INTERFACE

TABLE OF CONTENTS

GENERAL DESCRIPTION...........................................................2

ENCLOSURE INFORMATION ......................................................2

ADDRESSING .........................................................................3

ENROLLING............................................................................3

UNDERSTANDING THE LIGHTS .................................................3

WIRING THE INTERFACE..........................................................4

NX-582 LAYOUT......................................................................4

TERMINAL DESCRIPTION .........................................................4

WIRE REQUIREMENTS .............................................................5

PROGRAMMING THE INTERFACE ...............................................5

PROGRAMMING DATA ..............................................................6

PROGRAMMING THE LOCATIONS...............................................8

PROGRAMMING WORKSHEETS..................................................9

SPECIFICATIONS .................................................................. 12

Summary of content (12 pages)

PAGE 1
NX-582E AES RADIO INTERFACE TABLE OF CONTENTS GENERAL DESCRIPTION........................................................... 2 ENCLOSURE INFORMATION ...................................................... 2 ADDRESSING ......................................................................... 3 ENROLLING............................................................................ 3 UNDERSTANDING THE LIGHTS ................................................. 3 WIRING THE INTERFACE .................................
PAGE 2
GENERAL DESCRIPTION The NX582-E is a microprocessor-controlled AES radio interface. This interface allows any or all events from the NX8/NX8E control panel to be reported via the AES radio Models 7050-E, 7050-DLR (v2.2 or higher), 7450, 7450-XL, 7750, and 7750-F. ENCLOSURE INFORMATION Inside the can, several 2-holed insertion points have been constructed. This allows for either vertical or horizontal placement of the modules.
PAGE 3
ADDRESSING The NX582-E has a fixed address of 77. When programming the interface, enter the Program Mode and select the device address as [7]-[7]. (See "Programming the NX582-E", page 5.) ENROLLING The NX8/NX8E has the ability to automatically find and store in its memory the presence of all keypads, zone expanders, wireless receivers, and any other device on the keypad buss. This allows these devices to be supervised by the control panel and illuminate the "Service" LED if one is not detected.
PAGE 4
WIRING THE INTERFACE Wire the 3-position terminal on the NX582-E to the NX8/NX8E control panel keypad interface as follows: Positive to KP POS, COM to KP COM, and DATA to KP DATA. Connect the wiring harness from the NX582-E connector labeled J6 to the AES radio connector labeled J1. Refer to connection diagram. NX-582E LAYOUT TERMINAL DESCRIPTION Table 1.1 POS Connect to the KP POS terminal of the NX8/NX8E. Current draw is 30 mA for the NX582-E. COM Connect to the KP COM terminal of the NX8/NX8E.
PAGE 5
WIRE REQUIREMENTS Table 2.1 Length (Feet) Wire Gauge Connected to NX8/NX8E Connected to NX-320 250 24 24 500 24 22 1000 22 20 2000 20 16 2500 18 16 PROGRAMMING THE NX582-E USING THE LED KEYPAD • Entering the Program Mode To enter the Program Mode, press [r]-[8]. At this time, the five function LEDs (Stay, Chime, Exit, Bypass, & Cancel) will begin to flash. Next, enter the "Go To Program Code" (Factory Default is [9]-[7]-[1]-[3]).
PAGE 6
data. This procedure is repeated until the last segment is reached. Pressing the [#] key will exit from this location, and the "Armed" LED will illuminate again waiting for a new programming location to be entered. If the desired location is the next sequential location, press the [POLICE] key. If the previous location is desired press the [FIRE] key. If the same location is desired press the [MEDIC] key.
PAGE 7
1. Numerical Data Numerical data is programmed by entering a number from 0-255 on the numeric keys of the system keypad. To view the data in a location, a binary process is used. With this process, the LED=s for zones 1 through 8 are utilized, and the numeric equivalents of their illuminated LED=s are added together to determine the data in a programming location.
PAGE 8
PROGRAMMING THE LOCATIONS Location 0 - Account Code (6 segments numerical data) This account number is provided by AES. Enter the account code followed by a “10" in the segment immediately after the last digit. If the account code is 6 digits long, program all 6 digits. Location 1 - Partitions To Be Reported (1 segment feature selection data) This location contains the partition(s) that should be included when reporting via the AES radio.
PAGE 9
PROGRAMMING WORKSHEETS LOC 0 1 2 3 DESCRIPTION Account Code (from provider) Default: AAAAAA Partition Event Enables 5 – Partition 5 ‘ 1 - Partition 1 ‘ 2 - Partition 2 ‘ 6 – Partition 6 ‘ 3 - Partition 3 ‘ 7 – Partition 7 ‘ 4 - Partition 4 ‘ 8 – Partition 8 ‘ Transmission Format 0 - Contact ID ‘ 1 - SIA ‘ 2 - 4+2 ‘ Events That Can Be Enabled During Phone Fault (8 segments) Segment 1 5 - Tamper ‘ 1 - Alarm ‘ 2 - Restore ‘ 6 - Tamper Restore ‘ 3 - Shunt ‘ 7 - Trouble ‘ 4 - Shunt Restore ‘ 8 - Trouble Resto
PAGE 10
4 5 Segment 6 5 - Autotest ‘ 1 - Open ‘ 2 - Close ‘ 6 - Program Start ‘ 3 - Exit Error ‘ 7 - Program End ‘ 4 - Recent Close ‘ 8 - Download Start ‘ Segment 7 4- Ground Fault Restore ‘ 1- Download Complete ‘ 2- Cancel ‘ 5- Maintenance Test ‘ 3- Ground Fault ‘ 6- 8 Reserved Segment 8 Reserved Events That Can Be Enabled During Phone Fault (8 segments) Segments 1 - 7 Reserved Segment 8 1 – 7 Reserved 8 - Fail to Communicate / Data Lost ‘ Events That Can Be Enabled During Phone Normal (8 segments) Segment 1 5 -
PAGE 11
6 Segment 6 5 - Autotest ‘ 1 - Open ‘ 2 - Close ‘ 6 - Program Start ‘ 3 - Exit Error ‘ 7 - Program End ‘ 4 - Recent Close ‘ 8 - Download Start ‘ Segment 7 4 - Ground Fault Restore ‘ 1 - Download Complete ‘ 2 - Cancel ‘ 5 - Maintenance Test ‘ 3 - Ground Fault ‘ 6 – 8 Reserved Segment 8 Reserved Events That Can Be Enabled During Phone Normal (8 segments) Segment 1 - 7 Reserved Segment 8 1 – 7 Reserved 8 - Fail to Communicate - Data Lost ‘ SYSTEM NOTES 11
PAGE 12
SPECIFICATIONS OPERATING POWER 12VDC Supplied from NX8 or NX8E or NX-320 AUXILIARY POWER Supplied from NX8/NX8E or NX-320 CURRENT DRAW 30 mA OPERATING TEMPERATURE 32 to 120 degrees F DIMENSIONS 4.0" Wide 3.25" High 1.0" Deep SHIPPING WEIGHT 1 lbs. 1420 N. Main Street Gladewater, Texas 75647 Main 800-727-2339 Outside the US 903-845-6941 Main Fax 903-845-6811 Web: www.caddx.com www.ge-interlogix.com NX-582E INSTALLATION MANUAL NX582EIA03 REV.