IFS MC201-1P/1FS User Manual P/N 1076525 • REV A • ISS 07FEB12
Copyright Trademarks and patents Manufacturer Version Certification FCC compliance ACMA compliance European Union directives © 2012 UTC Fire & Security Company. All rights reserved. Interlogix, IFS MC201-1P/1FS, the IFS Brand and logo are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. UTC Fire & Security Americas Corporation, Inc.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. Contact information Customer support www.utcfireandsecurity.com or www.interlogix.com www.interlogix.
Contents Overview 1 About the MC201-1P/1FS 1 Package Contents 2 Hardware Overview 3 Front Panel 4 Back Panel 4 Link Fault Pass-through (LFP) 4 Link Loss Carry Forward (LLCF) 5 Link Loss Return (LLR) 6 Installing the Converter 7 PoE Function 8 LED Indicators 9 System 9 10/100Base-TX Port 9 100Base-FX SC Port 9 Specifications 11 Cable Specifications 12 RJ-45 Pin Assignments 12 RJ-45 Cable Pin Assignments 12 Fiber Optic Cable Connection Specifications 13 Contacting Technical Support 14 IFS MC201-1P/1FS User M
Overview Thank you for purchasing the IFS MC201-1P/1FS 10/100Mbps Ethernet Twisted pair to 100Base-FX fiber optic PoE Bridge Converter. This converter is used to convert one type of media signal to a different type of media that allows two segments to connect easily, efficiently and inexpensively. The converter supports Power over Ethernet to power one IEEE 802.3af compliant powered device. About the MC201-1P/1FS The MC201-1P/1FS is an IEEE 802.
PD (Powered Device) is a device powered by the PSE and thus consumes energy, such as IP Phones, network cameras and Wireless access points, etc. Package Contents Open the package containing the MCR205-1T/1S and carefully unpack it. The box should contain the following items: • MCR205-1T/1S PoE Media Converter x1 • User’s Manual CD x1 If any of these items are missing or damaged, please contact your dealer immediately.
Hardware Overview Figure 1: Physical Layout IFS MC201-1P/1FS User Manual 3
Front Panel There is one RJ-45 Twisted-Pair jack (Auto-MDI/MDI-X), one fiber-optic connector and four LED indicators on the MC2011P/1S front panel. Back Panel There is one DIP switch for turning the Link Fault Passthrough feature on or off, and 48V DC power input located at the back panel. The back panel also has one 48 VDC power socket for the MC201-1P/1S. Note: Please make sure that the 48VDC power supply used is capable to provide 0.32A to support full PoE load.
LLCF (Link Loss Carry Forward) detects the connection loss on the TP line, and LLR (Link Loss Return) detects the connection loss on the fiber line. Link Loss Carry Forward (LLCF) The MC201-1P/1FS incorporates an LLCF function for troubleshooting a remote connection. When LFP function is enabled, the FL/TP ports do not transmit a link signal until they receive a link signal from the opposite port.
Link Loss Return (LLR) The fiber ports of the MC201-1P/1FS have been designed with an LLR function for troubleshooting a connectivity issue. LLR works in conjunction with LLCF. When LFP function is enabled, the port’s transmitter shuts down when its receiver fails to detect a valid connection. LLR should only be enabled on one end of the link and is typically enabled on either the unmanaged or remote device.
Note: LFP function is turned-off by default. This feature can also be enabled or disabled via the side DIP-switch. If the installer is familiar with the network installation and diagnostics (i.e. checking which end is broken in a connection), switch can be set to ON position and converter should be reset for changes to take effect. Otherwise, it's recommended to keep the DIP switch in its default position. Installing the Converter Please follow these steps to install the MC201-1P/1FS: 1.
TX RX RX TX 100Base-FX Fiber Network 10/100Base-TX Cat. 5/5e TP Cable Network Note: RJ-45/STP, UTP Cat 5, straight /crossover cable is accepted. Please refer to the Cable Specification section for more details about the wiring distance of your TP, optical fiber networks. PoE Function The MC201-1P/1FS IEEE 802.3af Powered Device/Splitter equipment installation: It's recommended to check your network environment before the installation.
Note: The PoE feature requires the use of a recommended power adapter. LED Indicators System LED Color PWR Green Function Lit Indicates the device is powered. 10/100Base-TX Port LED Color Function Blink Indicates that the Media Converter is actively sending or receiving data over that port. LNK/ACT PoE in Use Lit Indicates that the connection through the port is successfully established. Off Indicates that the connection through the port is not established.
10 IFS MC201-1P/1FS User Manual
Specifications Ethernet Data Rate Throughput (packet per second) Switch Architecture 10/100/1000Mbps 148810pps@64Bytes Store-and-Forward Back pressure for Half-Duplex mode Flow Control Pause from for Full-Duplex mode (IEEE 802.
Cable Specifications Duplex Connection Limitation (max.
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connections: Fiber Optic Cable Connection Specifications The optical details are shown below: Fiber Optical patch Cables: Standard Fiber Type Cable Specification 100Base-FX (1310nm) Multi-mode 50/125μm or 62.
Contacting Technical Support Contact technical support if you encounter any difficulties during this installation. Please make sure you have the requested diagnostic or log files ready before you contact us by phone or go to www.interlogix.com/customer-support. Technical Support Europe, Middle East and Africa W Select Contact Us at www.utcfssecurityproducts.eu North America T +1 855.286.8889 E techsupport@interlogix.com Australia E 14 techsupport@interlogix.
