User Manual
Table Of Contents
- Preface
- Chapter 1 KTD-405/405A/405-2D overview
- Chapter 2 Installation
- Chapter 3 Programming
- Programming modes
- Supervisor programming
- Figure 17. Supervisor programming menu tree
- Figure 18. KB3 PTZ PROTOCOL display
- Figure 19. ENTER REMOTE PRGMG display
- Figure 20. KEYPAD TITLE display
- Figure 21. KEYPAD LOCKOUT PRIORITY displays
- Figure 22. Lowest user programmed preset menu
- Figure 23. PROGRAM SOFT KEYS display
- Figure 24. PRESS KEY TO PROGRAM display
- Figure 25. Command selection display
- Figure 26. Confirm command selection display
- Figure 27. CHANGE ACCESS CODES displays
- Figure 28. BAUD RATE display
- Figure 29. SYSTEM CONTROL display
- Figure 30. INACTIVE TIMEOUT display
- User programming
- Figure 31. OPERATING MODE menu
- Standard Digiplex menus
- Zone menus
- Figure 38. OPERATING MODE menu
- Figure 39. Zone menu
- Figure 40. ENTER ZONE ADDRESS menu
- Figure 41. ZONE xx TITLE menu
- Figure 42. SEND TO ALL KEYPADS display
- Figure 43. Zone hub display
- Figure 44. Zone monitor outputs
- Figure 45. Zone camera inputs
- Figure 46. Access restriction menus
- Figure 47. ZONE xx ACCESS menu
- Figure 48. Annunciation menu
- Figure 49. Call tone menu
- Figure 50. SPOT MONITOR NUMBER menu
- Remote programming
- Chapter 4 Operation
- Operating your keypad
- Standard Digiplex mode
- Figure 55. Normal operating display
- Selecting a monitor
- Selecting a camera
- Controlling a camera
- Setting a preset
- Recalling a preset
- Operating group switching on Digiplex IV switchers
- Setting autopan limits
- Controlling a DVMRe/multiplexer (hybrid mode)
- Controlling a recording device
- System information menus
- Help menu
- Audio
- Zone mode
- Chapter 5 Troubleshooting and support
- Appendix A Sample configurations and charts
- Sample analog system configurations
- Sample IP system configuration
- Receiver site addressing
- Reprogrammable keys and commands
- System planning chart
- Index
Chapter 1
KTD-405/405A/405-2D overview
5
Operating modes
The KTD-405 can be programmed to operate in two modes: standard Digiplex
®
or zone (DVMR/multiplexer/
PTZ control). (See Appendix A, Sample configurations and charts for layout samples of these modes.)
Note: Be aware that the addressing between domes and multiplexers is offset. When setting up and controlling your cameras in
zone mode, refer to Receiver site addressing on page 65.
Digiplex mode
Digiplex mode can be divided into two categories: standard Digiplex mode and hybrid Digiplex mode.
Standard Digiplex mode. In standard Digiplex mode, the system’s main switching device is a standard
matrix switcher. The keypad can address and control PTZ receiver sites, operate a matrix switcher with 128
monitor outputs, address and select views from 32 multiplexers, operate up to 32 recorders, and manage
access control points.
Note: The keypad can address and control 1599 PTZ’s using the RS485 and 1023 PTZ’s using RS422. Independent
permissions can be set for 1023 PTZ cameras.
Hybrid Digiplex mode. You can also operate a DVMRe/multiplexer when operating in a hybrid Digiplex
mode. This enables the DVMRe or multiplexer to provide multiscreen views by connecting the output of
the unit to an input on the matrix switcher. Digiplex mode (standard or hybrid) does not require that the
DVMRes have dedicated monitors. If you are using Calibur
™
units, they must be connected to the keypad’s
RS-485 control signal; other brands must be connected to the keypad’s RS-422 control signal using a
KTD-93 interface. When you press the zone key, the keypad switches to zone mode operation (hybrid
Digiplex mode), which enables it to control the DVMRe/multiplexer (right display in Figure 3). If the zone
is assigned to a camera input on the matrix switcher (done in programming), when you select the zone, the
keypad sends a command to the matrix switcher to call up the assigned input on the active monitor.
While in hybrid Digiplex mode, key functions are the same as those used during normal zone mode
operation, except the esc key, which returns the keypad to standard Digiplex mode of operation.
Note: Camera control (PTZ) is disabled while in hybrid mode
Figure 3. LCD menus showing standard and hybrid modes
CAMERA 0
MONITOR 1
Standard mode
ZONE 01 DVMRE
TRI
Hybrid mode