User Manual
Table Of Contents
- Preface
- Chapter 1 KTD-405/405A/405-2D overview
- Chapter 2 Installation
- Chapter 3 Programming
- Programming modes
- Supervisor programming
- Figure 17. Supervisor programming menu tree
- Figure 18. KB3 PTZ PROTOCOL display
- Figure 19. ENTER REMOTE PRGMG display
- Figure 20. KEYPAD TITLE display
- Figure 21. KEYPAD LOCKOUT PRIORITY displays
- Figure 22. Lowest user programmed preset menu
- Figure 23. PROGRAM SOFT KEYS display
- Figure 24. PRESS KEY TO PROGRAM display
- Figure 25. Command selection display
- Figure 26. Confirm command selection display
- Figure 27. CHANGE ACCESS CODES displays
- Figure 28. BAUD RATE display
- Figure 29. SYSTEM CONTROL display
- Figure 30. INACTIVE TIMEOUT display
- User programming
- Figure 31. OPERATING MODE menu
- Standard Digiplex menus
- Zone menus
- Figure 38. OPERATING MODE menu
- Figure 39. Zone menu
- Figure 40. ENTER ZONE ADDRESS menu
- Figure 41. ZONE xx TITLE menu
- Figure 42. SEND TO ALL KEYPADS display
- Figure 43. Zone hub display
- Figure 44. Zone monitor outputs
- Figure 45. Zone camera inputs
- Figure 46. Access restriction menus
- Figure 47. ZONE xx ACCESS menu
- Figure 48. Annunciation menu
- Figure 49. Call tone menu
- Figure 50. SPOT MONITOR NUMBER menu
- Remote programming
- Chapter 4 Operation
- Operating your keypad
- Standard Digiplex mode
- Figure 55. Normal operating display
- Selecting a monitor
- Selecting a camera
- Controlling a camera
- Setting a preset
- Recalling a preset
- Operating group switching on Digiplex IV switchers
- Setting autopan limits
- Controlling a DVMRe/multiplexer (hybrid mode)
- Controlling a recording device
- System information menus
- Help menu
- Audio
- Zone mode
- Chapter 5 Troubleshooting and support
- Appendix A Sample configurations and charts
- Sample analog system configurations
- Sample IP system configuration
- Receiver site addressing
- Reprogrammable keys and commands
- System planning chart
- Index
KTD-405/KTD-405A/KTD-405-2D Controller Keypad
User Manual
4
Product overview
GE Security’s KTD-405 is compatible with all GE Security products including DVMRs, multiplexers, matrix
switchers, alarm interfaces, CyberDomes, and Digiplex systems. The KTD-405 can select and switch video,
initiate camera tours, and select monitors.
The KTD-405A adds audio functionality to the unit, providing two-way voice communication with a built-in
speaker, amplifier, and audio microprocessor for automatic volume level.
Product contents
The KTD-405 (Figure 1) and KTD-405A (Figure 2) packages, in addition to the items shown, include this
KTD-405/KTD-405A/KTD-405-2D Controller Keypad User Manual (1036547) and a quick reference guide
(1047307). The KTD-405-2D (not shown) is similar to the KTD-405, but with a 2-axis joystick instead of a 3-
axis joystick.
Figure 1. KTD-405 package contents
Figure 2. KTD-405A package contents
Inspect the package and contents for visible damage. If any components are damaged or missing, do not use
the unit; contact the supplier immediately. If you need to return the unit, you must ship it in the original box.
Keypad
(N. America: KTD-405)
(Europe: KTD-405U)
Power supply
(1040077B)
I/O box
(1043406)
Power cord
(N. America: 1037376)
(Europe: 1037377)
RJ45 control cable
(1044203)
Keypad
(N. America: KTD-405A)
(Europe: KTD-405AU)
Power supply
(1040077B)
I/O box
(1043406)
RJ45 control cable
(1044203)
RJ11 audio cable
(D0304A894)
Power cord
(N. America: 1037376)
(Europe: 1037377)