User Manual
Table Of Contents
- Preface
- Chapter 1 KTD-405/405A/405-2D overview
- Chapter 2 Installation
- Chapter 3 Programming
- Programming modes
- Supervisor programming
- Figure 17. Supervisor programming menu tree
- Figure 18. KB3 PTZ PROTOCOL display
- Figure 19. ENTER REMOTE PRGMG display
- Figure 20. KEYPAD TITLE display
- Figure 21. KEYPAD LOCKOUT PRIORITY displays
- Figure 22. Lowest user programmed preset menu
- Figure 23. PROGRAM SOFT KEYS display
- Figure 24. PRESS KEY TO PROGRAM display
- Figure 25. Command selection display
- Figure 26. Confirm command selection display
- Figure 27. CHANGE ACCESS CODES displays
- Figure 28. BAUD RATE display
- Figure 29. SYSTEM CONTROL display
- Figure 30. INACTIVE TIMEOUT display
- User programming
- Figure 31. OPERATING MODE menu
- Standard Digiplex menus
- Zone menus
- Figure 38. OPERATING MODE menu
- Figure 39. Zone menu
- Figure 40. ENTER ZONE ADDRESS menu
- Figure 41. ZONE xx TITLE menu
- Figure 42. SEND TO ALL KEYPADS display
- Figure 43. Zone hub display
- Figure 44. Zone monitor outputs
- Figure 45. Zone camera inputs
- Figure 46. Access restriction menus
- Figure 47. ZONE xx ACCESS menu
- Figure 48. Annunciation menu
- Figure 49. Call tone menu
- Figure 50. SPOT MONITOR NUMBER menu
- Remote programming
- Chapter 4 Operation
- Operating your keypad
- Standard Digiplex mode
- Figure 55. Normal operating display
- Selecting a monitor
- Selecting a camera
- Controlling a camera
- Setting a preset
- Recalling a preset
- Operating group switching on Digiplex IV switchers
- Setting autopan limits
- Controlling a DVMRe/multiplexer (hybrid mode)
- Controlling a recording device
- System information menus
- Help menu
- Audio
- Zone mode
- Chapter 5 Troubleshooting and support
- Appendix A Sample configurations and charts
- Sample analog system configurations
- Sample IP system configuration
- Receiver site addressing
- Reprogrammable keys and commands
- System planning chart
- Index
Chapter 4
Operation
49
Selecting and controlling a DVMRe/multiplexer
When a zone is active, the corresponding DVMRe/multiplexer can be controlled by the keypad (Table 5).
Table 5. Controlling a multiplexer
Control Function for multiplexer Function for DVMRe
starts record mode starts record mode
starts playback mode (if multiplexer has an attached
DSR/VCR, a play command is sent to the multiplexer
and the VCR)
starts playback mode
stops playback or record mode stops playback or record mode
pauses live picture; pauses playback pauses playback or live view
toggles image between normal and 2X magnification
(joystick moves view)
zooms image to 2X magnification (toggle)
calls up screen to search for specific recording
puts DVMRe in playback mode
Joystick when attached to a DSR/VCR in pause mode
twisting right: steps forward at a variable rate
twisting left: steps in reverse at a variable rate
in any mode with 2X magnification
right: pans right
left: pans left
up: pans up
down: pans down
in play or pause mode
right: fast forwards
left: rewinds
up: skips forward approximately 15 sec
down: skips backward approximately 15 sec
twisting right: steps forward at a variable rate
twisting left: steps in reverse at a variable rate
return to center: resumes pause mode
with 2X magnification on
right: pans right
left: pans left
up: pans up
down: pans down
fast forwards playback fast forwards playback
rewinds playback rewinds playback
in pause mode, steps forward one frame in reverse: shifts play direction to forward
in pause mode: steps playback forward one frame
in pause mode, steps in reverse one frame playing forward: shifts play direction to reverse
in pause mode: steps playback in reverse one frame