User Manual
Table Of Contents
- Preface
- Chapter 1 KTD-405/405A/405-2D overview
- Chapter 2 Installation
- Chapter 3 Programming
- Programming modes
- Supervisor programming
- Figure 17. Supervisor programming menu tree
- Figure 18. KB3 PTZ PROTOCOL display
- Figure 19. ENTER REMOTE PRGMG display
- Figure 20. KEYPAD TITLE display
- Figure 21. KEYPAD LOCKOUT PRIORITY displays
- Figure 22. Lowest user programmed preset menu
- Figure 23. PROGRAM SOFT KEYS display
- Figure 24. PRESS KEY TO PROGRAM display
- Figure 25. Command selection display
- Figure 26. Confirm command selection display
- Figure 27. CHANGE ACCESS CODES displays
- Figure 28. BAUD RATE display
- Figure 29. SYSTEM CONTROL display
- Figure 30. INACTIVE TIMEOUT display
- User programming
- Figure 31. OPERATING MODE menu
- Standard Digiplex menus
- Zone menus
- Figure 38. OPERATING MODE menu
- Figure 39. Zone menu
- Figure 40. ENTER ZONE ADDRESS menu
- Figure 41. ZONE xx TITLE menu
- Figure 42. SEND TO ALL KEYPADS display
- Figure 43. Zone hub display
- Figure 44. Zone monitor outputs
- Figure 45. Zone camera inputs
- Figure 46. Access restriction menus
- Figure 47. ZONE xx ACCESS menu
- Figure 48. Annunciation menu
- Figure 49. Call tone menu
- Figure 50. SPOT MONITOR NUMBER menu
- Remote programming
- Chapter 4 Operation
- Operating your keypad
- Standard Digiplex mode
- Figure 55. Normal operating display
- Selecting a monitor
- Selecting a camera
- Controlling a camera
- Setting a preset
- Recalling a preset
- Operating group switching on Digiplex IV switchers
- Setting autopan limits
- Controlling a DVMRe/multiplexer (hybrid mode)
- Controlling a recording device
- System information menus
- Help menu
- Audio
- Zone mode
- Chapter 5 Troubleshooting and support
- Appendix A Sample configurations and charts
- Sample analog system configurations
- Sample IP system configuration
- Receiver site addressing
- Reprogrammable keys and commands
- System planning chart
- Index
KTD-405/KTD-405A/KTD-405-2D Controller Keypad
User Manual
48
Zone mode
The LCD displays the zone number and title on the top line and the current camera and monitor numbers on the
bottom line (Figure 61).
Figure 61. Zone mode main menu
To select a zone, press zone and enter the zone number.
The LCD displays the zone number and title, which is created during programming.
Selecting a camera
Use one of the following methods to enter the camera number to select a new camera.
• Enter the camera number including any preceding zeros. (For example, if you have tens of cameras,
enter 01 for camera 1; if you have hundreds of cameras, enter 001 for camera 1.)
• Enter the camera number directly (omitting preceding zeros), then press .
Controlling a camera
The control address of a PTZ camera in zone mode is offset from the number used to select it. When setting up
and controlling your cameras in zone mode, refer to Receiver site addressing on page 65 in Appendix A.
PTZ. Pan, tilt, and zoom are controlled by the joystick. Zoom is also controlled by the + zoom - key.
To pan, move the joystick left or right. To tilt, move the joystick up or down. To zoom, twist the joystick
knob clockwise or counterclockwise.
Focus. For autofocus, press the autofocus key. To focus manually, use the + focus - key.
Iris. The iris is controlled by the + iris - key; + opens the iris, - closes the iris.
Note: Refer to the CyberDome manual for additional operation on some CyberDome models.
Selecting a monitor
1. Press the mon key.
2. Enter the monitor number including any preceding zeros or enter the monitor number directly and
press enter.
ZONE --ZONE TITLE
CAMERA --MONITOR