User Manual
Table Of Contents
- Preface
- Chapter 1 KTD-405/405A/405-2D overview
- Chapter 2 Installation
- Chapter 3 Programming
- Programming modes
- Supervisor programming
- Figure 17. Supervisor programming menu tree
- Figure 18. KB3 PTZ PROTOCOL display
- Figure 19. ENTER REMOTE PRGMG display
- Figure 20. KEYPAD TITLE display
- Figure 21. KEYPAD LOCKOUT PRIORITY displays
- Figure 22. Lowest user programmed preset menu
- Figure 23. PROGRAM SOFT KEYS display
- Figure 24. PRESS KEY TO PROGRAM display
- Figure 25. Command selection display
- Figure 26. Confirm command selection display
- Figure 27. CHANGE ACCESS CODES displays
- Figure 28. BAUD RATE display
- Figure 29. SYSTEM CONTROL display
- Figure 30. INACTIVE TIMEOUT display
- User programming
- Figure 31. OPERATING MODE menu
- Standard Digiplex menus
- Zone menus
- Figure 38. OPERATING MODE menu
- Figure 39. Zone menu
- Figure 40. ENTER ZONE ADDRESS menu
- Figure 41. ZONE xx TITLE menu
- Figure 42. SEND TO ALL KEYPADS display
- Figure 43. Zone hub display
- Figure 44. Zone monitor outputs
- Figure 45. Zone camera inputs
- Figure 46. Access restriction menus
- Figure 47. ZONE xx ACCESS menu
- Figure 48. Annunciation menu
- Figure 49. Call tone menu
- Figure 50. SPOT MONITOR NUMBER menu
- Remote programming
- Chapter 4 Operation
- Operating your keypad
- Standard Digiplex mode
- Figure 55. Normal operating display
- Selecting a monitor
- Selecting a camera
- Controlling a camera
- Setting a preset
- Recalling a preset
- Operating group switching on Digiplex IV switchers
- Setting autopan limits
- Controlling a DVMRe/multiplexer (hybrid mode)
- Controlling a recording device
- System information menus
- Help menu
- Audio
- Zone mode
- Chapter 5 Troubleshooting and support
- Appendix A Sample configurations and charts
- Sample analog system configurations
- Sample IP system configuration
- Receiver site addressing
- Reprogrammable keys and commands
- System planning chart
- Index
Chapter 4
Operation
39
store With number keys, sets presets and autopan limits for selected camera; accesses sequence programming for
Calibur multiplexers.
Group. Activates group switching and group sequence initiation.
find With number keys, selects PTZ position saved by the previous store command for selected camera site.
Step
+zoom - Controls the zoom function on selected receiver site’s motorized zoom lens.
PTZ lockout on/off. Asserts or releases PTZ lockout priority. Lower priority keypads will lose PTZ control.
+focus - Controls the focus function on selected receiver site’s motorized zoom lens; disables the autofocus feature on
CyberDome.
Focus + = GRAB VID, Focus - = GRAB END
+iris - Controls the iris function on selected receiver site’s motorized zoom lens.
Backlight bright/dim
esc With number keys, clears alarms and clears number entry.
No shifted function.
1st Selects earliest of pending annunciations.
Macro
autofocus Places selected CyberDome camera in autofocus mode.
Autopan
0 – 9 Selects camera (selects any numeric entry following other keys).
No shifted function.
Places selected DSR, DVMRe, or VCR in fast forward mode.
Site up. Selects the camera number one more than the current one.
Places selected monitor’s DSR, VCR, or DVMRe in fast reverse mode.
Site down. Selects the camera number one less than the current one.
Advances selected DSR or DVMRe one frame forward in pause mode.
Joystick right
Steps selected DVMRe one frame backward in pause mode; selects reverse play in play mode.
Joystick left
Places selected DSR, VCR, or DVMRe in play mode.
Joystick down
Places selected DSR, VCR, or DVMRe in pause mode.
Joystick up
Table 3. Normal and shifted key functions (continued)
Key Function