User Manual
Table Of Contents
- Preface
- Chapter 1 KTD-405/405A/405-2D overview
- Chapter 2 Installation
- Chapter 3 Programming
- Programming modes
- Supervisor programming
- Figure 17. Supervisor programming menu tree
- Figure 18. KB3 PTZ PROTOCOL display
- Figure 19. ENTER REMOTE PRGMG display
- Figure 20. KEYPAD TITLE display
- Figure 21. KEYPAD LOCKOUT PRIORITY displays
- Figure 22. Lowest user programmed preset menu
- Figure 23. PROGRAM SOFT KEYS display
- Figure 24. PRESS KEY TO PROGRAM display
- Figure 25. Command selection display
- Figure 26. Confirm command selection display
- Figure 27. CHANGE ACCESS CODES displays
- Figure 28. BAUD RATE display
- Figure 29. SYSTEM CONTROL display
- Figure 30. INACTIVE TIMEOUT display
- User programming
- Figure 31. OPERATING MODE menu
- Standard Digiplex menus
- Zone menus
- Figure 38. OPERATING MODE menu
- Figure 39. Zone menu
- Figure 40. ENTER ZONE ADDRESS menu
- Figure 41. ZONE xx TITLE menu
- Figure 42. SEND TO ALL KEYPADS display
- Figure 43. Zone hub display
- Figure 44. Zone monitor outputs
- Figure 45. Zone camera inputs
- Figure 46. Access restriction menus
- Figure 47. ZONE xx ACCESS menu
- Figure 48. Annunciation menu
- Figure 49. Call tone menu
- Figure 50. SPOT MONITOR NUMBER menu
- Remote programming
- Chapter 4 Operation
- Operating your keypad
- Standard Digiplex mode
- Figure 55. Normal operating display
- Selecting a monitor
- Selecting a camera
- Controlling a camera
- Setting a preset
- Recalling a preset
- Operating group switching on Digiplex IV switchers
- Setting autopan limits
- Controlling a DVMRe/multiplexer (hybrid mode)
- Controlling a recording device
- System information menus
- Help menu
- Audio
- Zone mode
- Chapter 5 Troubleshooting and support
- Appendix A Sample configurations and charts
- Sample analog system configurations
- Sample IP system configuration
- Receiver site addressing
- Reprogrammable keys and commands
- System planning chart
- Index
Chapter 3
Programming
25
Entering a new preset number or pressing will take you to the display shown in Figure 23.
10. At the command selection display, use the joystick (or the
and keys) to scroll up and down
through the list of commands until you find the desired command. The commands are listed in
alphabetical order. Then press the key (
on the display) to save the selected command for the
reprogrammed soft key.
Note: Pressing the key returns you to the PRESS KEY TO PROGRAM display.
13. The KEY HAS BEEN PROGRAMMED display flashes briefly, then the PRESS KEY TO PROGRAM
display (Figure 24) returns. If you want to reprogram additional keys, repeat the process from step 4.
8. To change key assignments, press the + side
of the zoom, focus, or iris keys.
Figure 23. PROGRAM SOFT KEYS display
9. At the PRESS KEY TO PROGRAM display
(Figure 24), press any of the available
reprogrammable keys. You can also program
the shifted keys by holding the esc key and
pressing the key. (See Reprogrammable keys
and commands on page 67.)
Figure 24. PRESS KEY TO PROGRAM display
11. At the PRESS KEY TO PROGRAM display
(Figure 24), press any of the available
reprogrammable keys. (See
Reprogrammable keys and commands on
page 67.)
Figure 25. Command selection display
12. At the CONFIRM COMMAND SELECTON
display, press the + side of the zoom, focus,
or iris key to confirm the assignment of the
command for the key or press
to return to
the PRESS KEY TO PROGRAM display.
Figure 26. Confirm command selection display
PROGRAM SOFT KEYS?
_
PRESS KEY TO
PROGRAM:
SLW/STOP -Æ
STABILIZ
SLW/STOP -Æ
STABILIZ?