User Manual
Table Of Contents
- Preface
- Chapter 1 KTD-405/405A/405-2D overview
- Chapter 2 Installation
- Chapter 3 Programming
- Programming modes
- Supervisor programming
- Figure 17. Supervisor programming menu tree
- Figure 18. KB3 PTZ PROTOCOL display
- Figure 19. ENTER REMOTE PRGMG display
- Figure 20. KEYPAD TITLE display
- Figure 21. KEYPAD LOCKOUT PRIORITY displays
- Figure 22. Lowest user programmed preset menu
- Figure 23. PROGRAM SOFT KEYS display
- Figure 24. PRESS KEY TO PROGRAM display
- Figure 25. Command selection display
- Figure 26. Confirm command selection display
- Figure 27. CHANGE ACCESS CODES displays
- Figure 28. BAUD RATE display
- Figure 29. SYSTEM CONTROL display
- Figure 30. INACTIVE TIMEOUT display
- User programming
- Figure 31. OPERATING MODE menu
- Standard Digiplex menus
- Zone menus
- Figure 38. OPERATING MODE menu
- Figure 39. Zone menu
- Figure 40. ENTER ZONE ADDRESS menu
- Figure 41. ZONE xx TITLE menu
- Figure 42. SEND TO ALL KEYPADS display
- Figure 43. Zone hub display
- Figure 44. Zone monitor outputs
- Figure 45. Zone camera inputs
- Figure 46. Access restriction menus
- Figure 47. ZONE xx ACCESS menu
- Figure 48. Annunciation menu
- Figure 49. Call tone menu
- Figure 50. SPOT MONITOR NUMBER menu
- Remote programming
- Chapter 4 Operation
- Operating your keypad
- Standard Digiplex mode
- Figure 55. Normal operating display
- Selecting a monitor
- Selecting a camera
- Controlling a camera
- Setting a preset
- Recalling a preset
- Operating group switching on Digiplex IV switchers
- Setting autopan limits
- Controlling a DVMRe/multiplexer (hybrid mode)
- Controlling a recording device
- System information menus
- Help menu
- Audio
- Zone mode
- Chapter 5 Troubleshooting and support
- Appendix A Sample configurations and charts
- Sample analog system configurations
- Sample IP system configuration
- Receiver site addressing
- Reprogrammable keys and commands
- System planning chart
- Index
KTD-405/KTD-405A/KTD-405-2D Controller Keypad
User Manual
22
Supervisor programming
As explained in Entering programming modes on page 21, to enter the supervisor menus, from the ENTER
PROGRAMMING CODE menu, press 1-4-7-6-seq.
Note: This is the default factory supervisor programming code sequence. After you install your KTD-405 keypad, be sure to
change the supervisor programming code as soon as possible to avoid security problems. To change the programming code,
see Figure 27 on page 26 of this menu. This is a critical number since it is needed to change any of the access codes. Be sure
to store the new number in a safe place. If the number is lost, GE Security technical support can help you reset the keypad to
factory defaults. All keypad setup information will be lost.
1. At the first menu in supervisor programming mode, you have the option to erase the keypad’s
nonvolatile memory and reload factory values. If you chose YES, you have these further options:
RESET ALL. Resets all stored settings to factory default.
RESET ALL BUT TITLES. Retains the zone titles, but sets everything else to factory defaults.
CAMERA. Access the camera you want to reset before you enter the supervisor programming.
Selecting this will send a reset to the camera. This is for resetting or restarting GE PTZs, not for
clearing settings. (16x, CyberDome2, and Legend)
Pressing forwards you through programming without changing set parameters.
To skip this menu and go to the next, press - or
.
Figure 17. Supervisor programming menu tree
Note: All PTZ's that are capable will reset when you send this command.
RESET TO DEFAULTS?
NO
PARTIAL. ARE
YOU SURE?
RESET CAMERA X ?
ARE YOU SURE?
COMPLETE. ARE
YOU SURE?
1 = RESET ALL BUT
TITLES
INITIALIZING
DEFAULTS
KEYPAD ADDRESS: 99
(01-99)NEXT