GE-DS-82 and GE-DS-82PoE Managed Switch Installation Sheet Package Contents Thank you for purchasing the Interlogix 8-Port Fast Ethernet + 2-Port Gigabit TP/SFP Combo Managed PoE Switch. The following Managed Switch model numbers are covered in this sheet: • GE-DS-82 • GE-DS-82-PoE Open the box of the Managed Switch and carefully unpack it.
System Requirements Your switch is designed to operate with a variety of platforms, operating systems and network cards. Actual performance will depend on a combination of these components. Differences in performance can occur depending on the versions and types of platforms, operating system and network cards used. The minimum system requirements are: • Clients running Windows 98/ME, NT4.0, 2000/XP, Vista, MAC OS9 or later, Linux, UNIX or other platform compatible with TCP/IP protocols.
Terminal Setup There are three ways to access and setup your switch. They are: • • • RS-232 console Telnet Web Browser RS-232 console To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to the serial (console) port of the GE-DS-82 Managed Switch. The console port of the Managed Switch is DCE already, so that you can connect the console port directly through PC without the need of Null Modem.
Figure 2: The COM1 properties window Logon to the Console Once the terminal has connected to the device, Supply power to the GE-DS82 and the GE-DS-82-PoE Managed Switch, the terminal will display that it is running testing procedures. The following message asks for the login username and password. The factory default password for the login screen is: • Username: admin • Password: admin 4 of 11 P/N 1069669-EN • REV 1.
Figure 3: GE-DS-82 Login screen Note: For security reasons, please change and memorize the new password after this first setup. Passwords must be entered in lowercase letters in the console interface. P/N 1069669-EN • REV 1.
Telnet Setup 1. Connect an RJ-45 cable from the PC to a Switch port on the Managed Switch. Figure 4: RJ-45 connection diagram PC / Workstation with IE browser IP address: 192.168.0.X Managed switch RJ-45 / UTP cable IP address: 192.168.0.100 2. Launch the Hyper Terminal program. A terminal program is required to make the software connection to the Managed Switch. Windows' Hyper Terminal program is a good choice. Hyper Terminal can be accessed from the Start menu.
4. Change the Connect using drop-down menu to TCP/IP (Winsock) then input the Host address. The Managed Switches default IP address is 192.168.0.100 and the default telnet port number is 23, then press the OK button. Figure 6: The Connect to dialog window Log on to the Console Make sure the device has finished booting. Once telnet has connected to the device, the Hyper terminal will display the login request. The following message asks for the login username and password.
Figure 7: The Login request window Now you can configure the Switch by Telnet. Web Browser Setup Start Web Management The following shows how to start up the Web Management of the GE-DS-82 Managed Switch. Please note that the Managed Switch is configured through an Ethernet connection, make sure the manager PC must be set on the same IP subnet address. For example, the default IP address of the GE-DS-82 Managed Switch is 192.168.0.100, then the manager PC should be set at 192.168.0.
Figure 8: IP management diagram PC / Workstation with IE browser IP address: 192.168.0.X Managed switch RJ-45 / UTP cable IP address: 192.168.0.100 Login to the managed Switch 1. Enter the IP address http://192.168.0.100 (the factory-default IP address or one you have previously changed in the console) in the Web Browsers Address Field 2. The following dialog box appears, please enter the default password "admin" (or the password you have changed via console). The login screen in Figure 9 appears.
Figure 9: Login screen 3. After entering the username and password, the main screen appears as shown in Figure 10. Figure 10: Main Screen of the GE-DS-82 PoE 4. You can use the Web Management interface to continue the Switch management, please refer to the user manual for more information. NOTE: For security reasons, please change and memorize the new password after this first setup. 10 of 11 P/N 1069669-EN • REV 1.
Resetting the IP Address To reset the IP address to the default IP Address "192.168.0.100" or reset the login password to default value. Press the hardware reset button on the front panel for about 10 seconds. After the device has rebooted, you can login to the WEB Management interface within the same subnet of 192.168.0.xx. Figure 11: Reset button Contact information Thank you for purchasing UTC Fire & Security products.
