Data Sheet

Agency Compliance
Complies with FDA Performance
Standard for Laser Products, Title 21,
Code of Federal Regulations, Subchapter J
D1010
Remote
Host
2 Fibers
62.5/125µm MM
RS-232
or
RS-422*
1. Point to point (dual fiber)
RS-232
or
RS-422*
D1010
D1010WDMA
Remote
Host
1 Fiber
62.5/125µm MM
RS-232
or
RS-422*
2. Point to point (single fiber)
*Note: Unit can be used for transmission of
RS-232 or RS-422, but not simultaneously
RS-232
or
RS-422*
D1010WDMB
up to 2.5 miles
(4 km)
up to 2.5 miles
(4 km)
ifs
International
Fiber
Systems
Incorporated
203.426.1180
ifs
International
Fiber
Systems
Incorporated
203.426.1180
ifs
International
Fiber
Systems
Incorporated
203.426.1180
ifs
International
Fiber
Systems
Incorporated
203.426.1180
Specifications
Data
Data Interface: RS-232 (data lines only), or RS-422 (see note)
Data Rate: DC - 1.5 Mbps (NRZ)
Operating Mode: Asynchronous Simplex or Full-Duplex
Bit Error Rate: <1 in 10˚
Wavelength D1010: 850 nm, MM D1010WDMA: 850/1310 nm, MM
D1010WDMB: 1310/850 nm, MM D1020: 1310 nm, MM
D1030: 1310 nm, SM D1030WDMA: 1310 nm, SM
D1030WDMB: 1550 nm, SM
Number Of Fibers D1010: 2 D1010WDMA: 1 D1010WDMB: 1 D1020: 2
D1030: 2 D1030WDMA: 1 D1030WDMB: 1
Connectors
Optical: ST
Data and Power: Terminal Block with Screw Clamps
Electrical & Mechanical
Power:
Surface Mount: 12 VDC @ 150 mA
Rack: From Rack
Number of Rack Slots: 1
Current Protection: Automatic Resettable Solid-State Current Limiters
Circuit Board: Meets IPC Standard
Size (in./cm.) (LxWxH)
Surface Mount: 4.2 x 4.0 x 1.0 in., 10.7 x 8.9 x 2.5 cm
Rack Mount: 7.0 x 4.9 x 1.0 in., 17.8 x 12.5 x 2.5 cm
Shipping Weight: < 2 lbs./0.9 kg
Environmental
MTBF: > 100,000 hours
Operating Temp: -40° C to +74° C
Storage Temp: -40° C to +85° C
Relative Humidity: 0% to 95% (non-condensing)†
†May be extended to condensation conditions by adding suffix ‘–C’ to
model number for conformal coating.
NOTE: The D1010 Series is compatible with some RS-485 (4-wire) systems, consult factory.
Part Number Opt. Pwr. Budget Max. Distance*
Multimode
62.5/125µm**
Single Mode
9/125µm
2.5 miles (4 km)
2.5 miles (4 km)
2.5 miles (4 km)
8 miles (13 km)
37 miles (60 km)
PS-12VDC 12 Volt DC Plug-in Power Supply (Included)
PS-12VDC-230 12 Volt DC Plug-in Power Supply, 230 VAC Input (Included if specified at time of order)
Add ‘-R3’ to Model Number for R3 Rack Mount - No Charge (Requires R3 Rack purchased separately)
Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)
D1010
D1010WDMA
✧
D1010WDMB
D1020
D1030
D1030WDMA
✧
D1030WDMB
2
1
1
2
2
1
1
Fibers Required
14 dB
14 dB
14 dB
13 dB
20 dB
*Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget. ♦ All accessories are third party manufactured. ✧ WDMA must mate with a WDMB.
RS-232/RS-422 Data Transceiver (850 nm)
RS-232/RS-422 Data Transceiver (850/1310 nm)
RS-232/RS-422 Data Transceiver (1310/850 nm)
RS-232/RS-422 Data Transceiver (1310 nm)
RS-232/RS-422 Data Transceiver (1310 nm)
RS-232/RS-422 Data Transceiver (1310 nm)
RS-232/RS-422 Data Transceiver (1550 nm)
Accessories♦
Options
Description
Ordering Information
Made in the USA
Complies with FDA Performance
Standard for Laser Products, Title 21,
Code of Federal Regulations, Subchapter J
GE
Security
North America
T 888-GE-SECURITY
888-437-3287
F 503-691-7566
E [e-mail]
Asia
T 852-2907-8108
F 852-2142-5063
Australia and New Zealand
T 613-9239-1200
F 613-9239-1299
Europe
T 44-113-238-1668
F 44-113-253-8121
Latin America
T 305-593-4301
F 305-593-4300
gesecurity.com/ifs
Specifications subject to
change without notice
© 2008 General Electric Company
All Rights Reserved
interlogix.com
Specifications subject to change without notice.
© 2013 United Technologies Corporation
All rights reserved.
Interlogix is part of UTC Building & Industrial Systems,
a unit of United Technologies Corporation.
DT/DR3000 Series
North America
T 855-286-8889
Latin America
T 561-998-6114
DT/DR3000 Series
8
-Channel Contact Mapping Transmitters and Receivers
Specifications
Data
Input/Output Channels: 8
Contacts: 200 VDC, 0.5 amp, 12 watts, normally open
Response Time: 25 msec maximum
Wavelength
DT3010, DR3010: 850 nm, MM
DT3020: 1310 nm, MM
DT3025, DR3030: 1310 nm, SM
DR3030 1310 nm, MM or SM
Number Of Fibers
1
Connectors
Contacts and Power: Terminal Plug with screw clamps
Optical: ST or FC (see ordering information)
Electrical & Mechanical
Power:
Surface Mount: 12 VDC @ 150 mA
Rack: From Rack
Number of Rack Slots: 2
Current Protection: Automatic Resettable Solid-State Current Limiters
Circuit Board: Meets IPC Standard
Size (in./cm.) (LxWxH)
Surface Mount: 7.0 x 4.9 x 2.0 in., 17.8 x 12.5 x 5.0 cm
Rack Mount: 7.0 x 5.0 x 2.0 in., 17.8 x 12.7 x 5.0 cm.
Shipping Weight: < 2 lbs./0.9 kg
Environmental
MTBF: > 100,000 hours
Operating Temp: -40° C to +74° C*
Storage Temp: -40° C to +85° C*
Operating Temp: -10° C to +45° C
s
Storage Temp: -20° C to +35° C
s
Relative Humidity: 0% to 95% (non-condensing)
* W/O Battery
s
W/ Battery
Ordering Information
Part Number Description Fibers Required Optical Pwr. Budget Max. Distance*
Multimode 62.5/125µm** DT3010 Contact Mapping Transmitter (850 nm) 1 13 dB 2.5 miles (4 km)
DR3010 Contact Mapping Receiver (850 nm) 1 13 dB 2.5 miles (4 km)
DT3020
Contact Mapping Transmitter (1310 nm)
1 13 dB 8 miles (13 km)
DR3020
Contact Mapping Receiver (1310 nm)
1 13 dB 8 miles (13km)
Single Mode 9/125µm DT3025
Contact Mapping Transmitter (1310 nm)
1 14 dB 25 miles (40 km)
DR3030
Contact Mapping Receiver (1310 nm)
1 14 dB 25 miles (40 km)
Accessories ♦
PS12VDC1.5A-U 12VDC, 1.5A Plug-in Power supply (110/220VAC) with Universal power plug adapter kit (Included)
Options Add ‘-R3’ to Model Number for R3 Rack Mount- No Charge (Requires R3 Rack purchased separately)
Add ‘-B’ for DR Battery Backup
*Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget.
♦ All accessories are third party manufactured.