D7420-RSH D7420WDM-RSH D7420-RSH-R3 D7430WDM-RSH D7430WDM-RSH-R3 IFS Fiber Module Installation & Operation Instructions P/N 1063640 • REV B • ISS 01OCT11
D7400RSH SERIES 10 / 100 AUTO - MIDI (PORTS 1 - 3) 10 / 100 MIDI X (PORTS 1 - 3) FIBER LINK CONTACTS Transmit + (Pin 1) Transmit - (Pin 2) Receive + (Pin 3) Receive - (Pin 6) NOTE: Pins 4, 5, 7, 8 are not used. Receive + (Pin 1) Receive - (Pin 2) Transmit + (Pin 3) Transmit - (Pin 6) NOTE: Pins 4, 5, 7, 8 are not used.
D7400RSH SERIES FIBER PORT LINK / SPEED 10 / 100 PORT 1 2 3 TRUNK PRI SEC C D A DUPLEX 10 / 100 PORT B 1 2 3 POWER TRUNK E F 10 / 100 PORT G TRUNK 2 FIBER PORT SECONDARY H I A B C D E F G H I J 3 1 FIBER PORT PRIMARY J Link Speed (Channels 1 - 3) Simplex / Duplex (Channels 1 - 3) Fiber port SEC Fiber port PRI Power Port connection Power connection Fiber link contacts connection Optical cable port SECONDARY connector Optical cable port PRIMARY connector GREEN = 100 RED = 10 GREE
ETHERNET NETWORK PRIMARY PRIMARY FIBER ifs I n t e rn a t io n a l Fib e r S yst e m s I n co rp o ra t e d C2B - 4 FIBER LINK CONTACTS TRUNK POWER C2A - 3 C1B - 2 C1A - 1 I nt er nat i onal F i ber S y s t em s I nc or por at ed SECONDARY FIBER C2B - 4 FIBER LINK CONTACTS -2 POWER + 12 VDC - 1 REDUNDANT INTERCONNECT DATA PORT D7430WDM A B -RSH 4-PORT ETHERNET SWITCH REDUNDANT SELF-HEALING C1B - 2 C1A - 1 ifs I n co rp o ra t e d C2B - 4 FIBER LINK CONTACTS POWER C2A - 3 C1B - 2 TRUN
INSTALLATION INSTRUCTIONS FOR ADDITIONAL COMPONENTS REQUIRED TO MEET EMISSION REQUIREMENTS ON THE D74XX/D74XXWDM-RSH STAND ALONE UNITS AND D74XX-R3/D74XXWDM-RSH-R3 RACK UNITS. POWER CABLE MUST HAVE A FERRITE TOROID CORE IFS P/N LB2643801002, FAIR-RITE P/N 2643801002 INSTALLED NEAR THE CONNECTOR WITH CABLE PASSING THRU IT FIVE TIMES (FIVE TURNS). REQUIRED FOR STAND ALONE UNITS ONLY.
IF YOUR POWER OUTLET DOES NOT HAVE A CONNECTION TO GROUND: For proper installation the D74XX, D74XXWDM stand alone units must be attached to earth ground. Ordinarily, this is accomplished through the power supply. If your power outlet does not have a ground prong then a wire must be attached from the power connector to ground. Connect the green wire included, from ground to the power connector as shown below.
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by International Fiber Systems, Inc. could void the user’s authority to operate the equipment.
Contacting us For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any other documentation provided. If you still have questions, contact us during business hours (Monday through Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time). Table 3. Sales and support contact information Sales Phone: Toll-free: 888.437.3287 in the US, including Alaska and Hawaii; Puerto Rico; Canada. Outside the toll-free area: 503.885.5700.
Product Disassembly Instructions for WEEE Per European Directive 2002/95/EC Waste Electrical and Electronic Equipment Required Tools: One number 2 Phillips (crosstip) screwdriver. One number 2 flat screwdriver. For the enclosed box version: 1. Locate and remove box cover securement screws. Usually, but not limited to, at least 4 screws. 2. Lift off box top cover. 3. Locate and remove securement screws for printed circuit board. 4.
Copyright Trademarks and patents Manufacturer Certification FCC compliance ACMA compliance Canada European Union directives © 2011 UTC Fire & Security. All rights reserved. Interlogix and IFS names and logos are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. UTC Fire & Security Americas Corporation, Inc.
