D1010 D1010-R3 D1010WDMA D1010WDMA-R3 D1010WDMB D1010WDMB-R3 D1020WDMA D1020WDMA-R3 D1020WDMB D1020WDMB-R3 D1030WDMA D1030WDMA-R3 D1030WDMB D1030WDMB-R3 IFS Fiber Module Installation & Operation Instructions P/N 1062855 • REV B • ISS 01AUG11
D1000 (Small Box) RS232 DATA RS422 DATA 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 Signal Ground Data Input Data Output + Data Input - Data Input + Data Output - Data Output
D1010 RS232/RS422 TRANSCIEVER RECEIVE 8 RS232 REC RS422 RS422 XTMR TRANSMIT ifs Duplex multimode fiber optic cable } To D1000 or D2100 series module International Fiber Systems Incorporated + DATA IN 7 - DATA IN 6 + DATA OUT 5 - DATA OUT 4 RS232 OUT 3 2 + 12 VDC 1 POWER Signal Ground RS232 Input (Pins 7 and 8) RS422 Input (Pins 6 and 7) RS422 Output (Pins 4 and 5) RS232 Output (Pins 3 and 8) Black wire Black with white stripe
D1000 A B C D E 1 2 3 4 5 6 7 8 F A B C D E F Data Receive Data Receiver Data Transmitter Data Transmit Data / Power Connector Power LED illuminates LED illuminates LED illuminates NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE CORRECT OPERATIONAL STATUS OF THE UNIT.
D1000 (R3 Card) RS232 DATA RS422 DATA 7 6 5 4 3 2 1 7 6 5 4 3 2 1 Signal Ground Data Input Data Output + Data Input - Data Input + Data Output - Data Output
C-1232 REV Duplex multimode fiber optic cable +Data -Data +Data -Data } RS422 Input } RS422 Output } Power from R3 backplane RS232/ To D1010 D2100 series module RS422 TRANSCEIVER 7 6 5 4 3 2 1 ifs A RECEIVE TRANSMIT POWER D10XX__ B C A Data Receive B Data Transmit C Power LED illuminates Signal Ground RS232 Input RS232 Out
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by International Fiber Systems, Inc. could void the user’s authority to operate the equipment.
Contacting us For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any other documentation provided. If you still have questions, contact us during business hours (Monday through Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time). Sales and support contact information North America Toll-free: 855.286.8889 in the US, including Alaska and Hawaii; Puerto Rico; Canada. Outside the toll-free area: 503.885.5700.
Product Disassembly Instructions for WEEE Per European Directive 2002/95/EC Waste Electrical and Electronic Equipment Required Tools: One number 2 Phillips (crosstip) screwdriver. One number 2 flat screwdriver. For the enclosed box version: 1. Locate and remove box cover securement screws. Usually, but not limited to, at least 4 screws. 2. Lift off box top cover. 3. Locate and remove securement screws for printed circuit board. 4.
Copyright Trademarks and patents Manufacturer Certification ACMA compliance Canada European Union directives © 2011 UTC Fire & Security. All rights reserved. Interlogix and IFS names and logos are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. UTC Fire & Security Americas Corporation, Inc.
