Installation Instructions

ManualsBrandsInterlogix ManualsElectronicsConcord LCD Key Pad with 2 Way Voice

P/N 466-4434 • REV H • 13FEB15 1 / 9

Concord LCD Keypad with 2-Way Voice

Installation Sheet

Description

The Concord LCD Keypad with 2-Way Voice provides control

of all programming and operation of compatible security

systems.

The 2-line, 16-character display provides easy to read

messages to indicate the current status of the system. The

keypad includes police, fire, and auxiliary panic buttons that

can be activated anytime. An internal piezo provides system

status beeps for trouble and alarm indications.* Two-way audio

is achieved using an internal speaker and microphone

combination.*

A supervised hardwire zone provides an additional zone

without added wiring to the panel. Opening the removable

swing-down door reveals a label with basic system operating

commands.

* Not UL approved as a primary annunciator. Not investigated

for use as two-way verification.

Tools and Equipment needed

• 4-conductor, 18- or 22-gauge wire

• #2 Phillips screwdriver

• #6 screws and anchors (included)

• Screws for gang box installation

• Saw or utility knife for cutting wallboard

Installation

Installation Guidelines

• Mount the keypad in an environmentally controlled area

(32°F to 120°F/0°C to 49°C).

• When mounting the keypad, allow at least 6 inches below

it for the swing-down cover.

• When connecting two-way voice to the keypad, any

additional speaker devices on the system should be

connected in parallel with the keypad speaker connection.

Note: Siren volume will be reduced if connected in series.

This information differs from the information listed in the

Concord 4 Installation Manual.

• Do not exceed the maximum available power given in the

panel installation instructions.

• The hardwire zone is intended for use with intrusion

sensors only. This zone input does not provide power for

sensors such as PIRs, fire detectors, etc.

• Up to 16 keypads can be installed on a Concord 4 system

of which a maximum of two can be connected to two-way

audio or a single keypad plus an audio verification module.

Table 1: Keypad Power Usage

Current (mA)

Conditions

110

Maximum alarm current with the buzzer sounding

and the keypad illuminated from a button press

Typical operation

Power saving mode (no panel AC power)

Table 2: Maximum SuperBus and Audio Wire Lengths

Wire gauge (unshielded or

shielded)

Max. keypad wire length between

keypad and panel

750 feet

300 feet

Note: Interlogix recommends using shielded cable to prevent

crosstalk between the speaker and microphone.

Table 3: Maximum Hardwire Zone Wire Lengths

Wire gauge (unshielded or

shielded)

Max. keypad zone wire length

between keypad and sensor

100 feet

Hardwire zone End of Line (EOL) resistor should be 2K ohm.

Installing the Mounting Plate

1. Place the keypad on a flat surface so that the mounting

plate is facing as shown in Figure 1 on page 2.

2. Remove the mounting plate from the keypad as described

in Figure 1 on page 2.

Summary of content (9 pages)

PAGE 1
Concord LCD Keypad with 2-Way Voice Installation Sheet Description The Concord LCD Keypad with 2-Way Voice provides control of all programming and operation of compatible security systems. The 2-line, 16-character display provides easy to read messages to indicate the current status of the system. The keypad includes police, fire, and auxiliary panic buttons that can be activated anytime. An internal piezo provides system status beeps for trouble and alarm indications.
PAGE 2
Figure 1: Removing Mounting Plate From Keypad To enable the tamper function: 1. Remove the two small flathead screws that attach the terminal block plate to the mounting plate. 2. Mount according to the process above. Note: Tamper screws must be installed into a stud. Wiring the Keypad CAUTION: Use static electricity precautions when handling electronic components. Utiliser les précautions de l'électricite statique lors de la manipulation des composants électroniques. 3. 1.
PAGE 3
Wiring the Keypad – Speaker and Microphone 1. Pull the speaker and microphone wires through the access area. 2. Connect the speaker and microphone wires to the 9 position terminal block as shown in Figure 4 below, Figure 5 below and Figure 6 below. 3. If other audio devices will be installed on the system, wire accordingly as shown in the following diagrams.
PAGE 4
External Contact Wiring Figure 9: Function Key Decals Table 4: External switches Normally closed Normally open Short = Tamper Open = Tamper 2K ohm = Normal Short = Alarm Open = Alarm 2K ohm = Normal Note: A bus failure will result in a zone trouble condition. Attaching the Keypad to the Mounting Plate 1. Align the right side of the keypad over the hooks on the mounting plate. See Figure 8 below. 2.
PAGE 5
2. Press . The display should show SECURITY. 3. Press or until the display shows ACCESSORY MODULES, then press . The display should show BUS DEVICES. 4. Press . The display shows the lowest device address and its ID. The following example shows what a device address display may look like: UNIT - ID 0—02110185* *The 8-digit SuperBus ID number is also located on a label on the back of the keypad. 5. Press or to cycle through all bus device addresses until the keypad appears. 6.
PAGE 6
. Exit user programming mode. Status LEDs The keypad has LEDs that indicate the current system status at a glance. Table 6 below explains LED behavior. Troubleshooting Problem Action/Solution Keypad doesn’t power up (no display and no beeps when keys are pressed). Check for correct wiring connections at keypad and panel terminals.
PAGE 7
FCC compliance FCC Part 15 Information to the User Changes or modifications not expressly approved by Interlogix can void the user’s authority to operate the equipment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.
PAGE 8
Installer: Please provide this page to the end user.
PAGE 9
Concord LCD Keypad with 2-Way Voice Installation Sheet 9/9