MONO CHANNEL CLASS "D" AUTOMOTIVE AMPLIFIER G1-1200 / G1-2000 / G1-3000 INSTRUCTION MANUAL
CONGRATULATIONS ON YOUR PURCHASE Your new high fidelity mono block amplifier is designed to deliver maximum enjoyment and one year of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble free installation.
INSTALLATION MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface in this manner. 3. Remove amplifier. Drill four 3.5 m/m holes into mounting surface.
SPEAKER WIRING The Class "D" amplifier is a SINGLE CHANNEL dedicated subwoofer amplifier. Unlike other amplifiers, the Class "D" operates as a single channel and cannot be bridged. Don't be fooled by the outputs. Two outputs are used strictly for convenience and are paralleled internally on the amplifier. This means that if both outputs are used with one driver each, the amplifier sees the same load as if the same drivers are connected to only one output terminal. See diagram below.
SPEAKER WIRING MONO BRIDGED MASTER SLAVE Master Amplifier LINE INPUT GAIN LPF BASS BOOST MASTER SLAVE MASTER /SLAVE CH1 6V 0.2V 50Hz 250Hz 0dB 12dB REMOTE GAIN CONTROL CH2 FROM RADIO MASTER SLAVE Slave Amplifier LINE INPUT GAIN LPF BASS BOOST MASTER SLAVE MASTER /SLAVE CH1 6V 0.
SPEAKER WIRING MONO BRIDGED Master Amplifier SPEAKER digital mono block AMPLIFIER 30A 30A G1-2000 B+ FUSE POWER REM GND 30A Using a lead wire of 8 gauge or bigger connect from the master Amp's negative(-) speaker terminal to the slave Amp's negative(-) speaker terminal.
SPEAKER WIRING MONO BRIDGED (OPTION) FOUR AMPLIFIER/ ONE SUBWOOFER (DUAL VOICE COIL)CONFIGURATION SPEAKER Master Amplifier digital mono block AMPLIFIER 30A Voice Coil1 30A G1-2000 B+ FUSE POWER REM GND 30A Voice Coil2 Slave Amplifier SPEAKER digital mono block AMPLIFIER 30A 30A digital mono block AMPLIFIER SPEAKER 30A Slave Amplifier 6 POWER REM GND G1-2000 B+ FUSE 30A GND 30A digital mono block AMPLIFIER 30A REM G1-2000 B+ FUSE 30A POWER 30A Master Amplifier SPEAKER G1
POWER SUPPLY CONNECTIONS The Class "D" amplifier is designed to work within 10 to 16 volts DC. Before any wires are connected, the vehicle's electrical system should be checked for correct voltage supply with the help of a voltmeter. First check the voltage at the battery terminals with the ignition in the off position. The voltmeter should read no less than 12 volts. Next, check the battery with the engine running between 1500 and 2000 rpm. The voltmeter should now read between 13.5 and 14.5 volts.
OPERATION 1 2 3 4 LINE INPUT GAIN LPF BASS BOOST 5 6 7 MASTER SLAVE MASTER /SLAVE CH1 6V 0.2V 50Hz 250Hz 0dB 12dB REMOTE GAIN CONTROL CH2 1. RCA Input Jacks 2. Input Level Control 4. Bass Boost 5. Remote Control Jack 6. Master/Slave Switch 3. Low Pass Frequency 7. Slave Input Jack Control and Crossover 1. RCA Input Jacks - Low level-high impedance inputs. Use high quality RCA cables designed for mobile applications. 2. Input Level Control - Adjust the input level for the marked channels.
FRONT/REAR PANEL LINE INPUT GAIN LPF MASTER SLAVE BASS BOOST MASTER /SLAVE CH1 6V 0.
TROUBLE SHOOTING GUIDE This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly. SYMPTOM PROBABLE CAUSE SOLUTION No Audio Low or N.
SPECIFICATION AMPLIFIER G1-1200 G1-2000 G1-3000 RMS POWER / 1 ohm @ 1% T.H.D 1200W x 1 2000W x 1 3000W x 1 2 ohms @ 0.05% T.H.D 750W x 1 1000W x 1 2000W x 1 4 ohms @ 0.05% T.H.
WARRANTY WARRANTY LIMITATIONS The following is NOT covered under Interfire Audio's warranty program: 1. Product owned by anyone other than the original purchaser from an authorized Interfire Audio dealer. (The warranty is NOT transferable and will not apply to products purchased from unauthorized dealers.) 2. Speaker products that have been overpowered, causing thermal (burnt voice coil) and/or mechanical failure (ripped surrounds or spiders). 3.
Interfire Audio, Inc. Santa Fe Springs, CA 90670 www.interfireaudio.