User's Manual

Wi-Spi Intruder will not
start, Wi-Spi Intruder’s
White headlight LED is off.
1. Wi-Spi Intruder not turned on.
2. Battery is not charged.
3. Wi-Spi Intruder was not set to off
during charging.
4. Wheels locked for overload
protection.
1. Turn Wi-Spi Intruder on and sync it with your Wi-Fi
Control Device.
2. Charge Internal Wi-Spi Intruder battery.
3. Ensure Wi-Spi Intruder is off and charge Internal Wi-Spi
Intruder Battery.
4. Slide Wi-Spi Intruder's on / off switch to off, then switch it
on again and sync it with your Wi-Fi Control Device.
Wi-Spi Intruder will not start,
Wi-Spi Intruder’s white
headlight LED is blinking.
1. Wi-Spi Intruder’s battery is low.
1. Ensure Wi-Spi Intruder is off and charge Internal
Wi-Spi Intruder battery.
Wi-Spi Intruder doesn't
move forward fast enough.
1. The internal battery charge is
getting low.
1. Turn the Wi-Spi Intruder off and charge the internal Wi-Spi
Intruder battery.
Wi-Spi Intruder cannot move
in straight line.
1. Trim control is not set correctly. 1. Adjust the trim control on the Wi-Fi Control Device.
CORRECTIVE ACTION:
CAUSE:
TROUBLESHOOTING -Continued
ISSUE:
Keep the Wi-Spi Intruder away from face, eyes and hair at all times. Do not drive the Wi-Spi Intruder near or at other people or
animals. Use caution when driving. Make sure people around you know that you are playing with the Wi-Spi Intruder. The Wi-Spi
Intruder is recommended for use indoor only. Make sure that your Wi-Spi Intruder does not have the opportunity to drive in a wet or
hazardous area such as snow, water, mud, or dangerous rocks. The charger provided in this package is for charging the Wi-Spi
Intruder ONLY. Only use the Charger provided with the Interactive Toy Concepts Wi-Spi Intruder. Do not use any other source to
charge the Wi-Spi Intruder. Do not attempt to overcharge your Wi-Spi Intruder. Follow the charging instructions provided in this
instruction manual. Do not attempt to replace the Lithium Polymer rechargeable battery in the Wi-Spi Intruder! The Intruder’s Lithium
Polymer rechargeable battery is sealed inside the unit and is not replaceable. Any attempts to replace the Intruder's Lithium
Polymer Rechargeable battery will void the warranty. Do not throw battery into the fire. Rechargeable battery is only to be charged
under adult supervision. Never leave a battery unattended while it is being charged. Never leave a battery unattended in the
presence of children. The supply terminals are not to be short-circuited. The packaging should be kept since it contains important
information.
IMPORTANT SAFETY INFORMATION
Web site:
www.interactivetoy.com
PLEASE! DO NOT RETURN THIS PRODUCT TO ANY RETAIL STORE!
For any questions or problems with this product please contact us at: Email: [e-mail]
Phone: Inside North America: 1-866-214-2220 Outside North America: [phone]
Address: Interactive Toy Concepts, 17 Vulcan Street, Toronto, Ontario, Canada. M9W 1L3
Wi-Spi Intruder will not
start, Wi-Spi Intruder’s
white headlight LED is on.
1. Wi-Spi Intruder is not properly
synced with your Wi-Fi Control Device.
2. Another Wi-Fi Control Device is
already synced to it.
1. Sync your Wi-Spi Intruder properly with your Wi-Fi
Control Device.
2. Log off from another Device, then sync your Wi-Spi
Intruder with your Wi-Fi Control Device.
9
10
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to operate the equipment. Note: This equipment has been tested an
d found to
comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These Limits are designed to provide reasonable
protection against harmful interference in a residential installation. This generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turn the equipment off and on, the user is encouraged to try and correct the interference
by one or
more of the following measures: •Reorient or relocate the receiving antenna • Increase the separation between the equipment and
receiver •
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or
an experienced
radio/TV technician for help.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of
exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) durin
g normal
operation.
FCC NOTE: U.S. ONLY
This device complies with Industry Canada licence-exempt RSS standard(s). 1.Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including
interference that may cause undesired operation of the device."
Industry Canada Notice: Canada only.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
French:
1.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
2.radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.