User's Guide
Table Of Contents
- Chapter 1. Precautions
- Chapter 2. Certifications
- Chapter 3. Introduction
- Chapter 4. Planning Installation
- Chapter 5. Installing ADU
- Chapter 6. Installing BDU
- Chapter 7. Operating BDU
- Chapter 8. Using AptusLX
- Chapter 9. Specification
- Chapter 10. Warranty
- Chapter 11. Appendix
- Chapter 1. Precautions
- Chapter 4. Planning Installation
- Chapter 5. Installing ADU
- Figure 9: Antenna Dimensions
- Figure 10: ADU Mounting Template
- Figure 11: Recommended Mast Design using Inner Holes (with M6 Bolts)
- Figure 12: Recommended Mast Design using Outer Holes (with M10 Bolts)
- Figure 13: Mounting Antenna using Inner Holes (with M6 Bolts)
- Figure 14: Mounting Antenna using Outer Holes (with M10 Bolts)
- Figure 15: Installing 40A Pole Bushing inside Pole Tube
- Figure 16: Installing Pole Bracket
- Figure 17: Mounting Antenna on Pole Mounted Bracket
- Figure 18: Vent Hole
- Figure 19: Connecting RF Cable using Inner Holes (with M6 Bolts)
- Figure 20: Connecting RF Cable using Outer Holes (with M10 Bolts)
- Chapter 6. Installing BDU
- Figure 21: BDU Dimensions (Direct Mounting Type)
- Figure 22: BDU Dimensions (19-inch Rack Mounting Type_Optional)
- Figure 23: BDU Mounting Template
- Figure 24: Direct Mounting of BDU
- Figure 25: Attach Connector Tray to BDU
- Figure 26: Attach Rackmount Plate to BDU
- Figure 27: Intellian C700 System with Connected Devices
- Figure 28: BDU Back Panel View
- Figure 29: LAN Ports (RJ45) Pinout
- Figure 30: Phone Port (RJ14 & 6P4C) Pinout
- Figure 31: Using Cable Splitter with RJ14 Phones
- Figure 32: GPIO Connector Pinout
- Figure 33: Power Connector Pinout
- Figure 34: BDU to Antenna Cable Connection
- Figure 35: Grounding Stud Connection
- Chapter 7. Operating BDU
6
Intellian C700 - Marine Satellite Communication System
List of Figures
Chapter 1. Precautions 8
Figure 1: Earth Showing Iridium Satellite in Six Dened Orbital Planes 9
Chapter 4. Planning Installation 12
Figure 2: Potential RF Interference 12
Figure 3: RF Hazard Precautions 13
Figure 4: Above Deck Unit (ADU) / Antenna Unit 14
Figure 5: Below Deck Unit (BDU) 14
Figure 6: Unpacking System Package (with ADU & BDU Sub-package) 17
Figure 7: Unpacking BDU Package 17
Figure 8: Unpacking ADU Package 18
Chapter 5. Installing ADU 19
Figure 9: Antenna Dimensions 19
Figure 10: ADU Mounting Template 20
Figure 11: Recommended Mast Design using Inner Holes (with M6 Bolts) 21
Figure 12: Recommended Mast Design using Outer Holes (with M10 Bolts) 22
Figure 13: Mounting Antenna using Inner Holes (with M6 Bolts) 23
Figure 14: Mounting Antenna using Outer Holes (with M10 Bolts) 23
Figure 15: Installing 40A Pole Bushing inside Pole Tube 24
Figure 16: Installing Pole Bracket 24
Figure 17: Mounting Antenna on Pole Mounted Bracket 25
Figure 18: Vent Hole 25
Figure 19: Connecting RF Cable using Inner Holes (with M6 Bolts) 26
Figure 20: Connecting RF Cable using Outer Holes (with M10 Bolts) 26
Chapter 6. Installing BDU 27
Figure 21: BDU Dimensions (Direct Mounting Type) 27
Figure 22: BDU Dimensions (19-inch Rack Mounting Type_Optional) 28
Figure 23: BDU Mounting Template 29
Figure 24: Direct Mounting of BDU 29
Figure 25: Attach Connector Tray to BDU 30
Figure 26: Attach Rackmount Plate to BDU 30
Figure 27: Intellian C700 System with Connected Devices 32
Figure 28: BDU Back Panel View 33
Figure 29: LAN Ports (RJ45) Pinout 33
Figure 30: Phone Port (RJ14 & 6P4C) Pinout 34
Figure 31: Using Cable Splitter with RJ14 Phones 34