User's Guide
Table Of Contents
- Chapter 1. Precautions
- Chapter 2. Certifications
- Chapter 3. Introduction
- Chapter 4. Planning Installation
- Chapter 5. Installing ADU
- Chapter 6. Installing BDU
- Chapter 7. Operating BDU
- Chapter 8. Using AptusLX
- Chapter 9. Specification
- Chapter 10. Warranty
- Chapter 11. Appendix
- Chapter 1. Precautions
- Chapter 4. Planning Installation
- Chapter 5. Installing ADU
- Figure 9: Antenna Dimensions
- Figure 10: ADU Mounting Template
- Figure 11: Recommended Mast Design using Inner Holes (with M6 Bolts)
- Figure 12: Recommended Mast Design using Outer Holes (with M10 Bolts)
- Figure 13: Mounting Antenna using Inner Holes (with M6 Bolts)
- Figure 14: Mounting Antenna using Outer Holes (with M10 Bolts)
- Figure 15: Installing 40A Pole Bushing inside Pole Tube
- Figure 16: Installing Pole Bracket
- Figure 17: Mounting Antenna on Pole Mounted Bracket
- Figure 18: Vent Hole
- Figure 19: Connecting RF Cable using Inner Holes (with M6 Bolts)
- Figure 20: Connecting RF Cable using Outer Holes (with M10 Bolts)
- Chapter 6. Installing BDU
- Figure 21: BDU Dimensions (Direct Mounting Type)
- Figure 22: BDU Dimensions (19-inch Rack Mounting Type_Optional)
- Figure 23: BDU Mounting Template
- Figure 24: Direct Mounting of BDU
- Figure 25: Attach Connector Tray to BDU
- Figure 26: Attach Rackmount Plate to BDU
- Figure 27: Intellian C700 System with Connected Devices
- Figure 28: BDU Back Panel View
- Figure 29: LAN Ports (RJ45) Pinout
- Figure 30: Phone Port (RJ14 & 6P4C) Pinout
- Figure 31: Using Cable Splitter with RJ14 Phones
- Figure 32: GPIO Connector Pinout
- Figure 33: Power Connector Pinout
- Figure 34: BDU to Antenna Cable Connection
- Figure 35: Grounding Stud Connection
- Chapter 7. Operating BDU
20
Intellian C700 - Marine Satellite Communication System
Figure 10: ADU Mounting Template
5.2 ADU Mounting Template
The lower radome has two types of industry-standard mounting holes, each with four mounting points. This
hole pattern is compatible with other companies' mounting holes. Select one of the two mounting types to
secure the antenna to the desired mounting surface.
• Inner Hole Type: mount the antenna using 'Inner Drill Holes' (with M6 Bolts). Intellian offers the
Antenna Pole Mount Kit (separate purchase) that uses Inner Holes (with M6 Bolts) to mount the antenna
on a pole.
• Outer Hole Type: mount the antenna using 'Outer Drill Holes' (with M10 Bolts). Make a cut-out in the
ange using the 'Cutting Hole for Cable Connector' patten to avoid hiding the cable connector. Make
a cut-out in the ange using the 'Cutting Hole for Vent Hole' patten to avoid hiding the vent hole.
The mounting holes must be in the exact same place as shown in the provided mounting template below.
Bow
20
°
153
mm (6.02")
40
°
282.84 mm (11.13")
150
mm (5.91")
51.30 mm (2.02")
141 mm (5.55")
175.40 mm (6.90")
282.84 mm (11.13")
124
mm (4.88")
200
mm (7.87")
117.20 mm (4.61")
98.35 mm (3.87")
Outer Drill Hole
Ф 14mm (0.55")
diameter in 4 positions
Inner Drill Hole
Ф 8mm (0.31")
diameter in 4 positions
Cutting Hole
for Cable Connector
Ф 55mm (2.17")
Cutting Hole
for Vent Hole
Ф 40mm (1.57")
175.40 mm (6.90")
Antenna Mounting Template
Doc. No. KC7011
NOTE: This is a real-size template. Make sure the hole
placement for the antenna is the same with the template
even though the mast has a different shape, and mount
the antenna on a flat surface of the mast.