User Guide

ManualsBrandsintelbras ManualsSecurity Alarmintelbras PGM 8000 Security Alarm

User guid

PGM 8000

Expander

Congratulations, you have just purchased a product with Intelbras quality and security.

The PGM expander module has a relay output, giving the user the possibility to automate several

devices in your home or business, such as gates, automatic curtains, lamps and much more.

1. Care and security

» Follow all instructions in the manual/guide for product installation and handling.

» Perform the installation in environments not susceptible to factors such as rain, fog and

splashes of water.

» Wireless communication technology, when exposed to environments with high power

radiation, may suffer interference and have its performance impaired. Example: locations

near TV towers, AM/FM radio stations, amateur radio stations, etc.;

» Clean only the external part of the device, using only a damp cloth (do not use chemical

solvents);

» Do not subject the device to excessive pressure or knocks/falls;

» Do not cover the device with adhesives, paper or inks;

» Do not expose directly to sunlight;

» Conrm that the installation site is stable and appropriate;

» Only perform congurations and installations by qualied personnel.

This product has an internal battery/battery. After its useful life, the product must be

delivered to an Intelbras authorized technical assistance or directly perform the nal

destination environmentally appropriate avoiding environmental and health impacts.

If you prefer, the battery as well as other Intelbras brand electronics without use, can

be disposed of at any collection point of Green Eletron (manager of electrical and

electronic waste with which we are associated). If you have any questions about the

reverse logistics process, please contact us at (48) 2106-0006 or 0800 704 2767

(Monday to Friday from 8am to 8pm and Saturdays from 8am to 6pm) or via e-mail

suporte@intelbras.com.br.

LGPD - General Law for the Protection of Personal Data: Intelbras does not access,

transfer, capture, or perform any other type of treatment of personal data from this

product.

2. Technical specications

Frequency of operation RF signal from 915 to 928 MHz

Modulation DSSS BPSK 40 kbps

Maximum trans. power 11 dBm

Transmission range¹ 600 m with direct line of sight open eld²

DC supply voltage 12 Vdc to 24 Vdc

AC power supply Input: 100/240 Vac ~ 50-60 Hz

Internal non-rechargeable battery 3 Vdc CR2032

PGM output number 1 PGM 10 A / 125 Vac 10 A / 250 Vac

Operating temperature -10 to 50 °C @ 90% of humidity

Compatibility 8000 Wireless Security System

Anatel Homologation Yes

Protection against violation Tamper key

Anti-jamming Against invasive signals

Color White

Dimensions (W × H × D) 122 × 122 × 47 mm

Weight 200 grams

1Intelbras wireless systems are tested to the highest standards and bring high reliability, but due to

their use/installation in various scenarios, some considerations must be taken into account:

Transmitters/receivers may be disturbed by radio signals, natural interference, location of

operation of the devices, climatic issues and other adversities affecting the transmission

of data regardless of the frequency or technology used, since the means of transmission is

adverse and different from place to place.

The receivers/transmitters of the devices have an internal processing time, and only receive

the data necessary for communication between them after this particular time for the

system.

Wireless devices must be tested regularly to determine if sources of interference exist and

to protect against possible failures.

² The maximum range distance between the AMT 8000 alarm center and the PGM 8000 expander is

up to 600 m with direct line of sight in the open eld.

3. Features

» Low battery indication.

» Long battery life;

» Easy installation;

» Key for registration.

» Tamper protection key;

» Two Power options: AC 100/240 Vac ~ 50-60 Hz or DC: 12 Vdc to 24 Vdc;

» 1 internal 3 Vdc (CR2032) battery.

» Transmission frequency 915 MHz - 928 MHz;

» Protection against malicious signals;

» Encryption on data transmission between devices.

4. Registration at the center unit

To register the PGM expander with the alarm center, press the synchronization button on the

center and then press the button on the expander located at the back, as shown in the image

below, removing the product from the mounting bracket. Check if the LED on the front part of the

amplier will ash green, indicating the success of the registration. If the LED ashes orange, the

signal is intermittent or weak and if the LED ashes red, there was some fault and the process

must be repeated. The amplier will be addressed with the center unit according to the sequence

performed, respecting the maximum limit of 16 devices of this type.

PGM Expander Synchronization Key

To check if the PGM expander installation location is within the RF signal range, press the sync

button, and if the LED ashes green the communication is correct, in orange the communication

is intermittent/weak and in red there is no communication with the center unit.

To register other expanders/accessories through keyboard commands and further information/

congurations, please refer to the complete manual of the AMT 8000 center.

Note: when registering the PGM 8000 expander to the alarm center using the synchronization

key, perform the practice safely, because the alarm center is energized, so as not to bring risks

to the installer and the equipment.

5. Installation

The PGM 8000 expander has a specic base to be xed on various surfaces, such as walls,

among others. To remove the expander from the base when it is xed on some surface, slide

it up and to put it back on the standalone base if it is xed or in manual use, follow the base’s

indicative marking.

Fix the base with screws³ or double-sided tapes³ on the desired surface and after arranging the

wires of the installation as shown in the illustration, t it to the base. Make sure that the base

is correctly xed to the surface and the expander on the base, so that they do not come Off.

Power supply

Device to

be triggered

AC input

110 V 250 Vac

Bracket for xing on surfaces and output location of installation wires

³ Screws, double-sided tape and other accessories are not included with the PGM expander and must

be purchased separately.

Summary of content (2 pages)

PAGE 1
2. Technical specifications Frequency of operation Modulation Maximum trans. power Transmission range¹ DC supply voltage AC power supply Internal non-rechargeable battery PGM output number Operating temperature Compatibility Anatel Homologation Protection against violation Anti-jamming Color Dimensions (W × H × D) Weight User guid PGM 8000 Expander Congratulations, you have just purchased a product with Intelbras quality and security.
PAGE 2
6. Battery / DC Supply / AC Power / Relay Drive 7. Operation Warranty term The PGM 80000 extender has an internal 3 Vdc CR2032 non-rechargeable battery, used only when there is power outage to maintain communication with the center unit, in case of power outage the PGM output is deactivated. The battery connector is located internally on its board (not accessible, to change the battery must open the product cabinet by removing the screws).