User manual IVP 4000 smart
IVP 4000 smart Passive infrared sensor Congratulations, you have just purchased a product with Intelbras quality and safety. The passive infrared sensor IVP 4000 smart was developed by Intelbras with 100% digital technology.
Care and safety » This product is intended for Indoor environments. » Avoid touching the surface of the PIR, if necessary, use a soft cloth for cleaning. » Do not place objects in front of the sensor. To secure the detection area, avoid curtains, screens, screens, or any object that blocks the scan. » Wireless communication technology, when exposed to environments with high power radiation, can suffer interference and have its performance impaired.
Summary 1. Technical specifications 5 2. Characteristics 5 3. Product 5 3.1. Detection range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 4. Installing the IVP 4000 smart sensor 6 5. Configuring the IVP 4000 smart sensor (for cards in version 4410030/4 and firmware 2.0.0) 6 5.1. Sensitivity adjustment of the IVP 4000 smart sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Technical specifications Consumption Detection angle Detection range Operating Temperature Transmission frequency Detection method Battery Supervision Anti-jamming < 20 mA 115° 12 m - 10 °C to + 50 °C 433,92 MHz PIR LITHIUM CR123A 3 V Supervised (FSK) or unsupervised (OOK) Immunity against interference from malicious signals 2.
4. Installing the IVP 4000 smart sensor To install the sensor, carefully read the topic Care and safety and follow the procedure below: 1. Open the sensor front cover by pressing the sides. 2. With the help of a tool, drill a hole in the back cover for the screw. 3. Insert the CR123A battery and position the sensor in the desired location. The IVP 4000 smart does not need to be installed with an articulator as it already has a 15° inclination angle. 5.
» Economy Mode: the sensor takes a reading of the environment and immediately after motion detection and triggering it goes into sleep, which can last for a period of 30 seconds (environment with little movement) up to 2 minutes (environment with a lot of movement). During this period the indication LED is not activated and no new triggers are generated, as a notification has just been sent to the switch. After the sleep time, the sensor is monitoring the environment until detecting a new movement.
5.4. Low battery sensor The IVP 4000 SMART sensor controls the battery level. If it is critical (equal to or below 2.5V), it will send the information to the control panel. If the sensor is configured in unsupervised mode (OOK) and the low battery signal is enabled in the control unit, the information is sent during the trip. Otherwise, if the sensor is configured in supervised mode (FSK), low battery sending is done during supervision and triggering.
6. Test Once installed and energized, walk in the area to be protected simulating a possible intrusion. Observe if the sensor is able to detect your movements during the journey, by lighting the lens. Adjust its sensitivity if necessary or reposition the sensor installation. If the alarm control panel used is Intelbras, put it in test mode, this way it will not be necessary to observe the LED, as the control panel will indicate the sensor’s operation through siren beeps. 7.
Com o jumper JP2 na posição 1 (CONT) o sensor funcionará no modo CONT (Continuo inteligente), operando da seguinte forma: After power-up, the sensor will work continuously for 30 minutes so that the installer can make all the adjustments to the sensor. After this time the sensor goes into intelligent continuous mode.
8. Homologation 0912-14-0160 This equipment is not entitled to protection against harmful interference and may not cause interference to duly authorized systems. This is a product approved by Anatel, the approval number can be found on the product label, for queries go to the website:sistemas.anatel.gov.br/sch.
Warranty term It is established that this warranty is granted upon the following conditions: Client’s name: Client’s signature: Invoice number: Date of purchase: Model: Retailer: Serial number: 1.
Customer Support: (48) 2106 0006 Forum: forum.intelbras.com.br Support via chat: chat.intelbras.com.br Support via e-mail: suporte@intelbras.com.br Customer Service: 0800 7042767 Where to buy? Who installs it? 0800 7245115 Produced by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira Rodovia BR 459, km 124, 1325 – Distrito Industrial – Santa Rita do Sapucaí/MG – 37540-000 CNPJ 82.901.000/0016-03 – www.intelbras.com.br 01.