ISP2150 2U Rack Server Platform Product Guide A Guide for Technically Qualified Assemblers of Intel® Identified Subassemblies/Products Order Number: A09581-001
Disclaimer Intel Corporation (Intel) makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Intel assumes no responsibility for any errors that may appear in this document. Intel makes no commitment to update nor to keep current the information contained in this document. No part of this document may be copied or reproduced in any form or by any means without prior written consent of Intel.
Contents 1 Description Server Board Features ......................................................................................................... 9 Front Panel Controls and Indicators........................................................................... 10 Back Panel Connectors ............................................................................................. 11 Major System Elements .............................................................................................
Removing DIMMs ...................................................................................................... 34 Peripheral Devices ............................................................................................................. 35 Removing the Diskette Drive...................................................................................... 35 Re-installing the Diskette Drive ..................................................................................
Server Control Operations ......................................................................................... 85 Phonebook ................................................................................................................ 88 Management Plug-ins ................................................................................................ 89 FRUSDR Load Utility..........................................................................................................
5 Technical Reference Connectors....................................................................................................................... 112 ATX Style Front Panel Connector ............................................................................ 113 Main Power Connector ............................................................................................ 114 Fan Interface ...........................................................................................................
12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. Removing the Hard Drive Carrier from the Chassis ................................................... 36 Attaching the Drive to the Carrier............................................................................... 37 Attaching a Slim-line CDROM Drive to the CDROM Tray .......................................... 38 Installing a Slim-line CDROM Drive .........................
viii ISP2150 2U Rack Server Platform Product Guide
1 Description Server Board Features Table 1. Server Board Features Feature Description Processor Installed: Up to two Intel® Pentium® II or Pentium III processors operating at 1.8 V to 3.5 V. The server board’s voltage regulator is automatically programmed by the processor’s VID pins to provide the required voltage. Memory (DRAM) Four 72 bit sockets for 168-pin, gold contact, 100 MHz, PC/100 compliant, ECC or non-ECC, registered or unbuffered, SDRAM dual inline memory modules (DIMM).
Front Panel Controls and Indicators The front panel controls and indicators are located behind the front bezel of the ISP2150 as shown in Figure 1. To access the panel, grasp the bezel at its edges and gently pull it towards you. Figure 1. Front View of ISP2150 Figure 2 presents the controls and indicators for the unit. A E B C M L D F G K H I J OM09320 Figure 2. Front Panel Controls and Indicators A. B. C. D. E. F. G.
Back Panel Connectors A B K J C I H G F D E OM09321 Figure 3. Back Panel Connectors A. B. C. D. E. F. Table 2. Mouse connector Parallel Port connector PCI Expansion slots AC input power connector Power supply fault indicator Video connector G. H. I. J. K.
Major System Elements A B C D E F K J I H G OM09322 Figure 4. Major System Elements A. B. C. D. E. F. 12 Power supply Expansion slot covers PCI riser card bracket Server board Fan Hot-swap drive bay G. H. I. J. K.
Server Board Connector and Component Locations B A C E D F G H I J II HH GG FF EE DD CC K L M N BB AA O Z P Y Q X W V U T S R OM08561 Figure 5. Server Board Connector and Component Locations A. B. C. D. E. F. G. H. I. J. K. L. M. N.
Processor Each Pentium II or Pentium III processor is packaged in a cartridge. The cartridge includes the processor core with an integrated 16 KB primary (L1) cache, the secondary (L2) cache, and a back cover. The processor implements the MMX™ technology and maintains full backward compatibility with the 8086, 80286, Intel386™, Intel486™, Pentium, Pentium Pro, Pentium II, and Pentium III processors.
✏ NOTE Use DIMMs that have been tested for compatibility with the server board. Contact your sales representative or dealer for a current list of approved memory modules. Check the Intel Customer Support web site for the latest tested memory list: http://support.intel.com/support/motherboards/server/L440gx/compat.htm 440GX Host Bridge / Memory Controller The ISP2150 is designed around the Intel® 82440GX AGPSet (440GX).
Add-in Board Slots You can only add two PCI cards to this server. You must use the PCI slots on the riser card. Do not use any expansion slots on the server board. The server board has two full length standard PCI connectors on the riser card.
IDE Controller IDE is a 16 bit interface for intelligent disk drives with disk controller electronics onboard. The PCI/ISA/IDE Accelerator, also known as PIIX4e, is a multifunction device on the server board that acts as a PCI based Fast IDE controller.
Keyboard and Mouse The keyboard/mouse controller is PS/2-compatible. The server may be locked automatically if there is no keyboard or mouse activity for a predefined length of time, if specified through the System Setup Utility (SSU). Once the inactivity (lockout) timer has expired, the keyboard and mouse do not respond until the previously stored password is entered. ACPI The ISP2150 supports the Advanced Configuration and Power Interface (ACPI) as defined by the ACPI 1.0 and PC97 specifications.
One major function of the BMC is to autonomously monitor system management events, and log their occurrence in the nonvolatile System Event Log (SEL). These include events such as over-temperature and over-voltage conditions, fan failure, or chassis intrusion. To enable accurate monitoring, the BMC maintains the nonvolatile Sensor Data Record (SDR), from which sensor information can be retrieved.
The EMP Console uses three management plug-ins to monitor the server: • SEL Viewer • SDR Viewer • FRU Viewer The EMP Console also has Phonebook plug-in that can be used to create and maintain a list of servers and their phone numbers. ✏ NOTE EMP and PEP (Platform Event Paging) share your modem. PEP has priority over all applications except EMP. If an alert occurs, PEP will reset your modem and page you.
Using Passwords You can set the user password, the administrator password, or both passwords. If only the user password is set, you: • Must enter the user password to enter BIOS Setup or the SSU. • Must enter the user password to boot the server if Password on Boot is enabled in either the BIOS Setup or SSU. • Must enter the user password to exit secure mode. If only the administrator password is set, you: • Must enter the administrator password to enter BIOS Setup or the SSU.
Summary of Software Security Features The table below lists the software security features and describes what protection each offers. In general, to enable or set the features listed here, you must run the SSU and go to the Security Subsystem Group, menu. The table also refers to other SSU menus and to the Setup utility. Table 3. Software Security Features Feature Description Secure mode How to enter secure mode: Setting and enabling passwords automatically places the system in secure mode.
Table 3. Software Security Features (continued) Feature Description Control access to the system other than SSU: set user password. To control access to using the system, set a user password and enable it through Setup or the SSU. To disable a password, change it to a blank entry or press CTRL-D in the Change Password menu of the User Password Option menu found in the Security Subsystem Group. To clear the password if you cannot access Setup or the SSU, change the Clear Password jumper (see Chapter 5).
Equipment Rack Precautions SAFETY WARNINGS ANCHOR THE EQUIPMENT RACK: The equipment rack must be anchored to an unmovable support to prevent it from falling over when one or more servers are extended in front of it on slide assemblies. The anchors must be able to withstand a force of up to 113 kg (250 lbs.). You must also consider the weight of any other device installed in the rack. MAIN AC POWER DISCONNECT: You are responsible for installing an AC power disconnect for the entire rack unit.
2 Upgrading and Installing Server Components Tools and Supplies Needed • • • • Phillips (cross head) screwdriver (#1 bit and #2 bit) Jumper removal tool or needle nosed pliers Pen or pencil Anti-static wrist strap and conductive foam pad (recommended) Warnings and Cautions These warnings and cautions apply throughout this chapter. Only a technically qualified person should access the inside of the system.
ESD and handling boards: Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges. After removing a board from its protective wrapper or from the system, place it component-side UP on a grounded, static-free surface. If you place the baseboard on a conductive surface, the battery leads may short out. If they do, this will result in a loss of CMOS data and will drain the battery. Use a conductive foam pad if available but NOT the board wrapper.
Bezel Opening and Closing the Front Bezel With the bezel open you have access to all of your system’s front panel functions and indicators. With the bezel closed you can protect critical functions and still view the system’s indicators. To open the bezel, do the following: 1. Stand in front of the chassis and grasp the edges of the bezel from each side. 2. Gently pull the bezel towards you until it begins to separate from the chassis.
Locking and Unlocking the Front Bezel The bezel can be locked and unlocked to prevent unwanted access to the system. To lock the bezel: 1. Remove the keys from inside the bezel (they should be taped to the inside). 2. Close the bezel and insert the key into the lock. Turn the counterclockwise until it stops (about a quarter turn). The bezel is now locked and cannot be opened. To unlock the bezel, insert the key into the lock and turn the lock clockwise until it stops (about a quarter turn).
Covers Opening the Cover 1. Loosen the three screws on the rear of the system. 2. Pull the cover back and remove it from the chassis. OM09327 Figure 7. Opening the Cover Closing the Cover 1. Place the cover on the chassis and slide it forwards as far as possible. 2. Tighten the three screws on the rear of the chassis.
Processors WARNING If the server has been running, any installed processor and heat sink on the processor board(s) will be hot. To avoid the possibility of a burn, be careful when removing or installing server board components that are located near processors. CAUTIONS Processor must be appropriate: You may damage the server if you install a processor that is inappropriate for your server. Make sure your server can handle a newer, faster processor (thermal and power considerations).
Installing a Processor The server supports up to two Intel Pentium II or Pentium III processors (with 100 MHz system bus). If you are installing two processors, make sure they are the same speed, voltage, and stepping. 1. Observe the safety and ESD precautions at the beginning of this chapter and the additional cautions given here. 2. Remove the new processor from its anti-static package and place it on a grounded, static free surface or conductive foam pad. 3.
CAUTION, SINGLE-PROCESSOR CONFIGURATIONS If you install only one processor in a system, it must go in the primary connector (closest to the DIMM sockets). With a single-processor configuration, you must install a termination board and termination latch assembly (A) in the empty secondary connector (B) to ensure proper operation of your system. A termination board is provided with your system. A B OM09328 Figure 9. Installing a Termination Board A. B.
Memory Installing DIMMs The server only supports 100 MHz PC/100-compliant SDRAM. • Install from 32 MB to 2 GB of unbuffered memory, using up to four single or double-banked DIMMs • Or Install from 32 MB to 2 GB of registered memory, using up to four single or double-banked DIMMs Installed DIMMs must be the same speed and either all registered or all unbuffered. For a list of supported memory, call your service representative or visit the Intel Support website: Http://support.intel.
OM09318 Figure 10. Installing DIMMs 7. 8. 9. 10. Repeat the steps to install each DIMM. Ensure that no cables are protruding from the server chassis and then close the server. Connect all external cables and the power cord to the server. Turn on the monitor and then the server. Removing DIMMs CAUTION Use extreme care when removing a DIMM. Too much pressure can damage the socket slot. Apply only enough pressure on the plastic ejector levers to release the DIMM. 1. 2. 3. 4. 5. 6. 7. 8.
Peripheral Devices Removing the Diskette Drive 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. Disconnect the power (B) and signal (A) cables from the diskette drive. The connectors are keyed for ease in reconnecting them to the drive. A B C OM09316 Figure 11. Removing the Diskette Drive from the Chassis A. B. C. 3. 4. 5. 6. Signal cable Power cable Screws Remove and save the screws (C) that secure the diskette drive carrier to the front of the chassis.
Re-installing the Diskette Drive 1. Remove the 3.5-inch diskette drive from its protective wrapper, and place it component-side up on an anti-static surface. 2. Install the drive into the drive carrier and secure it with the screws that you removed. 3. Slide the drive carrier through the front of the chassis. 4. Secure the drive carrier to the front of the chassis with the screws you removed earlier. 5. Connect the signal and power cables to the drive according to the manufacturer’s specifications.
E A B D C OM09323 Figure 13. Attaching the Drive to the Carrier A. B. C. Hard disk drive Drive carrier Plastic slide rails (2) D. E. Screws (4) Connector end of drive 5. Align the drive holes to the holes in the drive carrier slide track (C), insert the screws that you previously removed, and attach the carrier (B) to the drive (A). Make sure that the connector end of the drive (E) is facing the back of the carrier and the drive top is facing upward before inserting the screws. 6.
Installing a Slim-line CDROM Drive Your server does not come with an integrated slim-line CD-ROM drive. You must purchase one separately and install it. 1. Remove the drive from its protective wrapper, and place it on an anti-static surface. 2. Set any jumpers and/or switches on the drive according to the drive manufacturer’s instructions. 3. Attach the CD-ROM drive to the CDROM tray using the mounting screws (A) supplied with the system. A OM09348 Figure 14.
A B C D OM09319 Figure 15. Installing a Slim-line CDROM Drive A. B. C. D. Signal cable Power cable Screws Retention screw 5. Slide the slim-line CDROM tray into the CDROM bay. It is recommended that you first remove the diskette drive in the section “Removing the Diskette Drive”. 6. Connect the CDROM IDE cable (A) and power (B) cables to the connector at the back of the CD tray. 7. Reinstall the diskette drive in the section “Re-Installing the Diskette Drive”. 8.
Add-in Cards Installing Add-in Cards You can only add two PCI cards to this server. You must use the PCI slots on the riser card. Do not use any expansion slots on the server board. 1. Remove the expansion slot cover for the slot you wish to use. Remove the thumbscrew (B) holding the cover retention bracket (A) to the chassis. Remove the bracket from the chassis. 2. Remove the expansion slot cover (C) for the slot you wish to use. B A C OM09325 Figure 16. Removing the Slot Cover Retention Bracket A. B.
3. Remove the add-in board from its protective wrapper. Set jumpers or switches according to the manufacturer’s instructions. A B OM09326 Figure 17. Installing an Add-in Card A. B. PCI slot Add-in card bracket 4. Hold board by its top edge or upper corners. Firmly press it into an open expansion slot on the riser card. The tapered foot of the board-retaining bracket must fit into the mating slot in the expansion slot frame. Install the board component side DOWN.
Power Supply Removing and Re-installing a Power Supply To replace the power supply: 1. Unplug the power cord from the power source and from the power cord receptacle (A) at the right rear side of the system. 2. Remove the top cover of the system. Refer to “Opening the Cover” on page 29. 3. Remove and save the two screws (B) from the power supply cover (C). 4. Grasp the bottom edge of the power supply cover and lift it up and away from the power supply. 5.
System Mounts There are two methods for installing the ISP2150, using the front bracket hardware or optionally using rack rail system. Installing the Front Bracket and Racking the System The ISP2150 system comes with mounting bracket hardware that allows you to install it into cabinets and relay racks. The following procedures describe how to mount the ISP2150 system in each type of chassis. Installing the Front Bracket in a Cabinet 1. Attach the left and right front brackets to the system.
5. Mount the front bracket to the cabinet. To complete the installation, bolt the system’s front brackets to the cabinet using the mounting bolts (A in Figure 21) supplied by the cabinet manufacturer. A A OM09346 Figure 21. Mounting the Front Brackets to the Cabinet Chassis Installing the Front Bracket in a Center-Mount, Relay Rack 1. Attach the left and right front brackets to the system.
Installing the Rail Rack and Racking the System (Optional Accessory) The rail kit that comes with your system allows you to install it into a four-post, network server cabinet (e.g. APC Netshelter). If the cabinet is not of this general type, you will have to purchase a separate rail kit that is specific to your cabinet. Follow these steps to install the rail kit and place your system into the cabinet. 1. Assemble tools and miscellaneous parts.
4. Here is a combination side and rear view (Figure 26) of the chassis after the right inside rail has been attached. Figure 26. Chassis Rear and Side View 5. Locate the front and rear rail brackets for one side of the rail kit. One pair (A and B in Figure 27) exists for each side of the cabinet rack. B A OM09145 Figure 27. Rail Brackets 6. Attach all four rail brackets to the cabinet rack. Be sure that the sharper angled side of each bracket is facing up (C in Figure 28).
7. Attach the side rail system’s outer pieces (total of two) to the rail brackets you installed in step six. To attach the front part of an outer piece to a rail bracket, you must reveal the access hole (A in Figure 29) by sliding the innermost piece toward the back. Once you see the access hole, align it with the slot in the rail bracket such that you can secure the bolt. Do not tighten the nut and bolt until you have aligned the rear portion of the rail system (see the next step).
9. Extend the right and left rails (A in Figure 31) so they fully extend in front of the cabinet rack. The rail system is now ready to receive the chassis. A A OM09141 Figure 31. Extending the Rails 10. Lift the chassis with its front facing you and carefully guide the inner rail (A in Figure 32), which is mounted to the chassis system, into the outer pieces (B in Figure 32) you attached in previous steps. Gently move the system evenly towards the rear of the cabinet.
Replacing the Back up Battery The lithium battery on the server board powers the real time clock (RTC) for up to 10 years in the absence of power. When the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM in the RTC (for example, the date and time) may be wrong. Contact your customer service representative or dealer for a list of approved devices. WARNING Danger of explosion if battery is incorrectly replaced.
B A C OM07843 Figure 34. Replacing the Lithium Battery 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. Open the chassis. 3. Insert the tip of a small flat bladed screwdriver, or equivalent, under the tab in the plastic retainer. 4. Gently push down on the screwdriver to lift the battery. 5. Remove the battery from its socket. 6. Dispose of the battery according to local ordinance. 7.
3 Configuration Software and Utilities This chapter describes the Power On Self Test (POST) and server configuration utilities. The table below briefly describes the utilities. Table 4. Configuration Utilities Utility Description and brief procedure Page BIOS Setup If the system does not have a diskette drive, or the drive is disabled or mis-configured, use Setup to enable it.
Power On Self Test (POST) Each time you turn on the system, POST starts running. POST checks the server board, processor, memory, keyboard, and most installed peripheral devices. During the memory test, POST displays the amount of memory that it is able to access and test. The length of time needed to test memory depends on the amount of memory installed. POST is stored in flash memory. 1. Turn on your video monitor and server. After a few seconds POST begins to run. 2.
Using BIOS Setup This section describes the BIOS Setup options. Use Setup to change the server configuration. You can run Setup with or without an operating system being present. Setup stores most of the configuration values in battery backed CMOS; the rest of the values are stored in flash memory. The values take effect when you boot the server. POST uses these values to configure the hardware; if the values and the actual hardware do not agree, POST generates an error message.
Starting Setup You can enter Setup after power on or reset by pressing F2. After booting, you will see the following prompt: Press to enter SETUP If CMOS/NVRAM has been corrupted, you will see other prompts: Warning: cmos checksum invalid Error 0271: check date and time settings In this condition, the BIOS will load default values for CMOS and attempt to boot.
Main Menu You can make the following selections on the Main Menu itself. Use the submenus for other selections. Feature Choices Description System Time HH:MM:SS Sets the system time System Date MM/DD/YYYY Sets the system date Legacy Diskette A: Disabled 360KB 1.2 MB 720KB 1.44/1.25 MB 2.88 MB Selects the diskette type Legacy Diskette B: Disabled 360KB 1.2 MB 720KB 1.44/1.25 MB 2.
Primary/Secondary IDE Master and Slave Submenu Feature Choices Description Type Auto None CD-ROM IDE Removable Auto forces the server to attempt autodetection of the drive type. None informs the server to ignore this drive. CD ROM allows the manual entry of some fields described below. IDE Removable allows the manual entry of some fields described below. ATAPI Removable allows the manual entry of some fields described below. User allows the manual entry of all fields described below.
Keyboard Submenu Feature Choices Description Num Lock On Off Selects the power on state for Num Lock. Key Click Disabled Enabled Enables or disables the audible key click. Keyboard auto-repeat rate 30/sec 26.7/sec 21.8/sec 18.5/sec 13.3/sec 10/sec 6/sec 2/sec Sets the numbers of time per second a key will repeat while it is held down. Keyboard auto-repeat delay 1/4 sec 1/2 sec 3/4 sec 1 sec Sets the delay before a key starts to repeat when it is held down.
Advanced Menu You can make the following selections on the Advanced Menu itself. Use the submenus for the three other selections that appear on the Advanced Menu. Feature Choices Description Installed OS Other Plug-N-Play Select Plug-N-Play if you are booting a Plug and Play capable operating system. Reset Configuration Data No Yes Select Yes if you want to clear the server configuration data during next boot. System automatically resets to No in next boot. PCI Configuration Enters submenu.
PCI Device, Slot 1 - Slot 6 Submenus Feature Choices Description Enable Master Enabled Disabled Enables selected device as a PCI bus master. Latency Timer Default 020h 040h 060h 080h 0A0h 0C0h 0E0h Minimum guaranteed time, in units of PCI bus clocks, that a device may be master on a PCI bus. CAUTION Do not change this setting unless you fully understand the priority of this device on the PCI bus. Note: Bold type indicates the default choice.
Integrated Peripheral Configuration Submenu (continued) Feature Choices Description Interrupt IRQ 5 IRQ 7 Selects the IRQ for LPT port. DMA channel DMA 1 DMA 3 Selects the DMA for LPT port (only used for ECP mode). Floppy disk controller Disabled Enabled Enables onboard diskette controller. Note: Bold type indicates the default choice. Advanced Chipset Control Feature Choices Description 640-768K Memory Region Enabled Disabled Enabled forwards ISA Master and DMA cycles to the PCI bus.
Security Menu You can make the following selections on the Security Menu itself. Enabling the Supervisor Password field requires a password for entering Setup. The passwords are not case-sensitive. Feature Choices Description User Password is Clear Set Status only; user cannot modify. Once set, this can be disabled by setting it to a null string, or by clearing password jumper on server board. Supervisor Password is Clear Set Status only; user cannot modify.
Server Menu You can make the following selections on the Server Menu itself. Feature Choices Description System Management Enters submenu. Console Redirection Enters submenu. PEP Management Enters submenu. Enable Sleep Button Disabled Enabled Enables optional ACPI support for the sleep button. PCI IRQs to IOAPIC mappings Disabled Enabled Enabled - BIOS can describe all 24 IO APIC pins in the MP table for PCI interrupts.
System Management Submenu (continued) Feature Choices Description EMP Hang-up Line String ATH Sets the Hang-up Line Sequence for the modem being used for EMP. Used in EMP modem mode. Modem Init String AT&F0S0=1S14=0&D Sets the initialization string for the modem being used for EMP. Used in EMP modem mode. This field is only 16 characters long. The High Modem Init String field is a continuation of the Modem Init string so you can enter in another 4 characters.
Console Redirection Submenu Feature Choices Description COM Port Address Disabled 3F8 2F8 3E8 When enabled, console redirection uses the I/O port specified. 3F8 - typically is COM1 2F8 - typically is COM2 All keyboard/mouse and video will be directed to this port. This is designed to be used only under DOS in text mode. IRQ # N/A This field is informational only. Baud Rate 9600 19.2k 38.4k 115.2k When console redirection is enabled, specifies the baud rate to be used.
PEP Filter Submenu This submenu allows you to set which events or error conditions cause the system to page you. Feature Choices Description PEF Enable Disable Enable Enables the Platform Event Filtering. If this is enabled, and one of the events you enable below occurs, the server will page you using the Page String information. Temperature Sensor Disable Enable Temperature out of range notification. Voltage Sensor Disable Enable Voltage out of range notification.
Boot Menu (continued) Feature Choices Description Extended RAM Step 1 MB 1 KB Sets extended memory test to verify once every KB, every MB, every location, or not at all (no test). Every location No memory test BIOS Boot Spec Support Limited Disabled The limited choice may be required if more than eight drives are installed in certain configurations. Boot Device Priority Enters submenu. Hard Drive Enters submenu. Removable Devices Enters submenu. Note: Bold type indicates the default choice.
Removable Devices For options on this menu, use the up or down arrow keys to select a device, then press the <+> or <-> keys to move the device higher or lower in the boot priority list. Option Description 1. Legacy Floppy Drive Refers to the onboard 3.5” floppy drive. Removable IDE media may also show up here if the removable media was formatted in floppy emulation. Exit Menu You can make the following selections on the Exit Menu.
When to Run the System Setup Utility The SSU is a DOS-based utility that supports extended system configuration operations for onboard resources and add-in boards. You can also view the system event log and to set system boot and security options.
Running the SSU • • Running the SSU Locally Running the ssu.bat file provided on the SSU media starts the SSU. If the server boots directly from the SSU media, the ssu.bat file is automatically run. If it boots from a different media, the SSU can be started manually or by another application. When the SSU starts in the local execution mode (the default mode), the SSU accepts input from the keyboard and/or mouse. The SSU presents a VGA based Graphical User Interface (GUI) on the primary monitor.
5. This message appears: Please wait while the Application Framework loads.... 6. When the main window of the SSU appears, you can customize the user interface before continuing. Figure 35.
Customizing the SSU The SSU lets you customize the user interface according to your preferences. The AF sets these preferences and saves them in the AF.INI file so that they take effect the next time you start the SSU. There are four user customizable settings: • Color - this button lets you change the default colors associated with different items on the screen with predefined color combinations. The color changes are instantaneous. • Mode - this button lets you set the desired expertise level.
Resource Configuration Add-in (RCA) Window The RCA provides three major functions: • Creates representations of devices that cannot be discovered by the system (ISA cards) • Modifies the contents of the system by adding and removing devices • Modifies the resources used by devices You can use the RCA window to define an ISA card or add an ISA card by clicking on the appropriate button.
Adding and Removing ISA Cards Adding and removing cards through the RCA provides a way for the RCA to run its conflict detection algorithms on the resources requested by the cards. This alerts you to any possible problems with that particular card in the current configuration. • To add an ISA card: 1. Click on Add ISA Card in the RCA window. 2. Specify the directory for the .CFG file. 3. Select the file and click on Ok. • To remove an ISA card: 1.
Security Add-in Under this window, you can set the User and Administrator passwords, and security options. To Set the User Password 1. Click on the user password button. 2. Enter the password in the first field. 3. Confirm the password by entering it again in the second field. To Change or Clear the User Password 1. 2. 3. 4. Click on the User password button. Enter the old password in the first field. Enter the new password in the second field (or leave blank to clear).
SEL Manager Add-in Clicking on the SEL Manager Add-in task brings up the Server Event Log (SEL) viewer. You can load and view the current SEL data stored in the BMC, save the currently loaded SEL data to a file, view previously saved SEL data, or clear the SEL. The SEL Viewer has the following menus: File The File menu has the following options: • Load SEL… View data from a previously saved SEL file. • Save SEL… Save the currently loaded SEL data to a file. • Clear SEL Clears the SEL data from the BMC.
FRU Manager Add-in Clicking on the FRU Manager Add-in task brings up the Field Replaceable Unit (FRU) viewer. You can load and view the current FRU data stored in the BMC, save the currently loaded FRU data to a file, view previously saved FRU data. The FRU Viewer has the following menus: File The File menu has the following options: • Load… View data from a previously saved FRU file. • Save… Saves the currently loaded FRU data to a file. • Save As… Saves the currently loaded FRU data to a file.
SDR Manager Add-in Clicking on the SDR Manager Add-in task brings up the Sensor Data Record (SDR) viewer. You can load and view the current SDR data stored in the BMC, save the currently loaded SDR data to a file, view previously saved SDR data. The SDR Viewer has the following menus: File The File menu has the following options: • Load… View data from a previously saved SDR file. • Save… Saves the currently loaded SDR data to a file. • Save As… Saves the currently loaded SDR data to a file.
Platform Event Paging With Platform Event Paging (PEP), your server can be configured to automatically dial up a paging service and page you when a server management related event occurs. Platform events include temperature out-of-range, voltage out-of-range, chassis intrusion, and fan failure. If PEP is enabled and the BMC receives or detects a new event, it automatically sends a page. It can send a page if the processors are down or if the system software is unavailable.
Emergency Management Port Console The Emergency Management Port (EMP) Console is a software application designed to run on a Windows 98 or Windows NT 4.0 workstation and provides a server administrator’s interface to the Emergency Management Port (EMP) of the ISP2150 server. This interface allows remote server management via a modem or direct connection.
How EMP Console Works The EMP shares use of the COM2 port with the system on the server. When the EMP has control of the port, the port operates in command mode. When the system has control, the port operates in console redirect mode. When connecting to a server, the EMP Console checks to determine the mode of the COM2 port. The following discussion covers how EMP Console functions in each mode: • Command mode is the default COM2 state.
Figure 37. EMP Console in Redirect State Figure 37 shows EMP Console window in redirect mode with the terminal window. The text that appears on the server monitor displays in the Redirect window. Availability of the various EMP Console features are determined by two factors: the BIOS EMP access mode and if the server’s COM2 port is configured for console redirection. The three EMP access modes are disabled, pre-boot, and always active. Table 6.
Table 7.
Setting up the Server for the EMP To use the EMP, you must configure the server’s BIOS with specific settings. These settings are found in two submenus of the BIOS Server menu, the System Management Submenu and the Console Redirection submenu. The BIOS settings section, found earlier in this document, shows all the available options. This section focuses on the settings that must be configured in order to use the EMP. System Management Submenu All EMP related settings occur in the Server main menu.
Main EMP Console Window The main EMP Console window provides a graphical user interface (GUI) to access server control operations and to launch the management plug-ins. At the top of the window is the menu and tool bar. These provide the options to initiate plug-ins and other support features. A status bar at the bottom displays connection information such as server name, line status, and mode.
EMP Console Main Menu • File • Exit - exits EMP Console. Connect Disconnect - disconnects the server connection. [Re]Connect - displays the connect dialog. • A list of the five most recent modem connections. Click on one of these server names to initiate a connection. Action Power On/Off - displays the Power on/off dialog. Reset - displays the Reset dialog. SEL Viewer - displays the SEL Viewer. SDR Viewer - displays the SDR Viewer. FRU Viewer - displays the FRU Viewer.
Connect When [Re]Connect is selected from the Connect menu, the Connect dialog in Figure 38 is displayed. This dialog allows you to connect to a server. If the client machine is already connected to a server, initiating connection generates a warning message. The message indicates that the existing connection will be terminated if you continue trying to initiate the new connection. You are prompted to enter the EMP password whenever a connection is attempted. Figure 38.
Power On/Off Selecting Power On/Off from the Action menu displays the Power on/off dialog. This dialog provides commands to remotely power on or power off the server. Figure 39. Power On/Off Dialog Options available in the dialog are: • Power ON - powers on the server. • Power OFF - powers off the server. This option is not allowed if the server is configured in RESTRICTED mode for EMP operations. • Post-power-up option - sets the mode selection of the server to EMP active or BIOS redirection.
Options available in the dialog are: • System Reset - resets the server with the selected post-reset options. This operation is not allowed if the server is configured in RESTRICTED mode for EMP operations. • Post-reset option - sets the post-reset option that will be in effect after reset. The options are EMP active or BIOS redirection. The default selection is EMP active. • Cancel - exits the Connect dialog without taking any action. • Help - displays the help information for this dialog.
• • Cancel - exits the Connect dialog without taking any action. Help - displays the help information for this dialog. Management Plug-ins SEL Viewer The SEL Viewer provides access to the System Event Log on the server and can display records in either hexadecimal or text (verbose) form.
• View SEL Information - displays SEL summary information as returned by the server. All Events - displays all events in the SEL. • By Sensor Type - displays all events in the SEL generated by a specific sensor type such as voltage, temperature, etc. A submenu lets you select the sensor type to be displayed. By Event - displays all the events in the SEL of a particular event type; for example, threshold, digital, or discrete. A pop-up menu lets you select the event type to be displayed.
• • • Settings – changes the operating parameters for the SDR Viewer. This menu displays the following suboption: Display HEX/Verbose - toggles between HEX mode and interpreted mode of displaying SDR records. Window - gives options for displaying currently open windows. Help Help Topics - help topics for EMP Console. Help About - provides version information.
FRUSDR Load Utility The Field Replacement Unit (FRU) and Sensor Data Record (SDR) Load Utility is a DOS-based program used to update the server management subsystem’s product level FRU, SDR, and the Desktop Management Interface (DMI) nonvolatile storage components (EEPROMs).
How You Use the FRUSDR Load Utility This utility is compatible with ROM-DOS Ver. 6.22, MS-DOS† Ver. 6.22, and later versions. The utility accepts CFG, SDR and FRU load files. The executable file for the utility is frusdr.exe. The utility requires the following supporting files: • one or more .fru files describing the system’s field replaceable units • a .cfg file describing the system configuration • a .
Displaying DMI Area The DMI area is displayed in ASCII format when the field is ASCII or as a number when the field is a number. Each DMI area displayed is headed with the DMI area designated name. Each field has a field name header followed by the field in ASCII or as a number. Displaying FRU Area The FRU area is displayed in ASCII format when the field is ASCII or as a number when the field is a number. Each FRU area displayed is headed with the FRU area designated name.
Updating the SDR Nonvolatile Storage Area After the utility validates the header area of the supplied SDR file, it updates the SDR repository area. Before programming, the utility clears the SDR repository area. The SDR file is loaded via the .cfg File. Then the utility filters all tagged SDRs depending on the product configuration set in the Configuration File. Nontagged SDRs are automatically programmed. It contains an image of what was loaded, and the TMP file is also useful for debugging the server.
Obtaining the Upgrade Utility You can upgrade to a new version of the BIOS using the new BIOS files and the BIOS upgrade utility, iFLASH.EXE. You can obtain the BIOS upgrade file and the iFLASH.EXE utility through your computer supplier or from the Intel Customer Support website: http://support.intel.com/support/motherboards/server/LB440gx ✏ NOTE Please review the instructions distributed with the upgrade utility before attempting a BIOS upgrade.
Upgrading the BIOS The following procedure describes how to upgrade the BIOS. Once the upgrade starts, do not shut down the system until the process completes. If the system is brought down during the upgrade, refer to the section “Recovering the BIOS” for how to proceed. 1. Boot the computer with the floppy disk in drive A. 2. A menu is displayed. Type 1 to automatically update the BIOS and continue at step 9, or type 2 to run the Iflash.exe utility and follow steps 3 to 8. 3.
7. 8. 9. 10. 11. Listen to the speaker. Two beeps and the end of activity in drive A indicate successful BIOS recovery. A series of continuous beeps indicates failed BIOS recovery. If recovery fails, return to step 1 and repeat the recovery process. If recovery is successful, turn off the computer. Remove the computer cover and continue with the following steps. 12. Move the Recovery Boot jumper back to pins 9-10. 13. Replace the computer cover. Leave the upgrade disk in drive A and turn on the computer.
10. Shut the system down and remove any floppy disks that may be in the system. 11. Disconnect the AC power cord from the system and wait 60 seconds. 12. Connect the AC power cord and power up the system. Installing Video Drivers After configuring the system, you need to install video drivers to take full advantage of the features of the onboard Cirrus Logic CL-GD5480 super VGA video controller. • The LB440GX Resource CD includes video drivers for use with DOS and Windows NT. Check the README.
ISP2150 2U Rack Server Platform Product Guide
4 Solving Problems This chapter helps you identify and solve problems that might occur while you are using the system. Resetting the System To do this: Press: Soft boot reset, which clears system memory and reloads the operating system. or Reset button on system front panel Cold boot reset. Turn the system power off and then on. This clears system memory, restarts POST, reloads the operating system, and halts power to all peripherals.
Checklist q Are all cables correctly connected and secured? q Are the processors or processor termination board fully seated in their slots on the server board? q Are all add-in PCI boards fully seated in their slots on the riser card? q Are all switch and jumper settings on the server board correct? q Are all jumper and switch settings on add-in boards and peripheral devices correct? To check these settings, refer to the manufacturer’s documentation that comes with them.
After the System Has Been Running Correctly Problems that occur after the system hardware and software have been running correctly often indicate equipment failure. Many situations that are easy to correct, however, can also cause such problems. Checklist q If you are running the software from a diskette, try a new copy of the software. q If you are running the software from a CD-ROM disk, try a different disk to see if the problem occurs on all disks.
More Problem Solving Procedures This section provides a more detailed approach to identifying a problem and locating its source. Preparing the System for Diagnostic Testing CAUTION Turn off devices before disconnecting cables: Before disconnecting any peripheral cables from the system, turn off the system and any external peripheral devices. Failure to do so can cause permanent damage to the system and/or the peripheral devices. 1. Turn off the system and all external peripheral devices.
Specific Problems and Corrective Actions This section provides possible solutions for these specific problems: • Power light does not light. • There is no beep or an incorrect beep pattern. • No characters appear on screen. • Characters on the screen appear distorted or incorrect. • System cooling fans do not rotate. • Diskette drive activity light does not light. • Hard disk drive activity light does not light. • CD-ROM drive activity light does not light. • There are problems with application software.
3. If there are still no characters on the screen after you reboot the system and POST emits a beep code, write down the beep code you hear. This information is useful for your service representative. See “Port-80 Codes and Countdown Codes” on page 110. 4. If you do not receive a beep code and characters do not appear, the video display monitor or video controller may have failed. Contact your service representative or authorized dealer for help.
Diskette Drive Activity Light Does Not Light Check the following: q Are the diskette drive power and signal cables properly installed? q Are all relevant switches and jumpers on the diskette drive set correctly? q Is the diskette drive properly configured? q Is the diskette drive activity light always on? If so, the signal cable may be plugged in incorrectly. If you are using the onboard diskette controller, use the SSU to make sure that “Onboard Floppy” is set to “Enabled.
✏ NOTE Front panel hard disk LED indicates IDE and SCSI devices: The hard disk drive activity light on the front panel lights when either an IDE hard disk drive, or a SCSI device controlled by the onboard SCSI host controller, is in use. This LED does not display CD-ROM activity. Cannot Connect to a Server q Make sure you are using the drivers that are shipped on the system Configuration Software CD for the onboard network controller. q Make sure the driver is loaded and the protocols are bound.
The controller stopped working when an add-in adapter was installed. q Make sure the cable is connected to the port from the onboard network controller. q Make sure your PCI BIOS is current. Try the “PCI Installation Tips” below. q Make sure the other adapter supports shared interrupts. Also, make sure your operating system supports shared interrupts; OS/2† does not. q Try reseating the add in adapter. The add-in adapter stopped working without apparent cause.
Error and Informational Messages When you turn on the system, POST displays messages that provide information about the system. If a failure occurs, POST emits beep codes that indicate errors in hardware, software, or firmware. If POST can display a message on the video display screen, it causes the speaker to beep twice as the message appears.
5 Technical Reference This chapter includes the following: • Environmental specifications • Board interrupts • Electromagnetic Compatibility (EMC) notices 111
Connectors The figure shows connector locations on the server board. This section provides pin information about the connectors. A C D E B F G H I Q J P O N M L K OM08839 Figure 42. Connector Locations A. B. C. D. E. F. G. H. I. 112 Fansink connector 2 Fansink connector 1 Main power connector ATX Aux power connector SM IMB Fan connector 2A ATX front panel connector Front panel connector, 16 pin ISOL IMB J. K. L. M. N. O. P. Q.
ATX Style Front Panel Connector J6J1 1 A B C D E 19 F OM07498 Figure 43. ATX Style Front Panel Connector Table 8. ATX Style Front Panel Connector Pinout Connector A. Power switch Pin 1 2 3 Signal Power switch GND N/C B. Hard drive activity LED 4 5 6 7 Current limited +5V Key HD activity LED Current limited +5V C. Speaker 8 9 10 11 GND N/C PIEZO_IN SPKR_HDR D. Power LED 12 13 14 15 Current limited +5V N/C GND N/C E. Reset switch 16 17 GND Reset switch F.
Main Power Connector Table 9. Main Power Connector Pinout Pin Signal Pin Signal 1 +3.3V 13 +3.3V 2 +3.3V 14 -12V 3 COM 15 COM 4 +5V 16 PS_ON 5 COM 17 COM 6 +5V 18 COM 7 COM 19 COM 8 PWR_OK 20 -5V 9 +5VSB 21 +5V 10 +12V 22 +5V 11 +12V 23 +5V 12 +3.3V 24 COM Fan Interface The server board has five 3-pin fan connectors that are shrouded and keyed.
Server Board Jumpers WOL ENABLE BMC WR EN J5A2 1 1 J4J2 J3J1 BMC FRC UP BIOS WR EN J2J1 INT DET RCVRY BOOT FRB PSWD CLR 1 CMOS CLR 1 OM08429 Figure 44. Jumper Locations Table 11. Server Board Jumper Summary Jumper Block Jumper Name Pins (default in bold) What it does at system reset J5A2 WOL ENABLE 1-2, Disabled Disables Wake On LAN. If your power supply does not provide 0.8 A of +5 V Standby current, you must move the WOL Enable jumper to this position.
Table 11. Server Board Jumper Summary (continued) Jumper Block Jumper Name Pins (default in bold) What it does at system reset J2J1 CMOS CLR 1-2, Protect Preserves the contents of NVRAM. 2-3, Erase Replaces the contents of NVRAM with the manufacturing default settings. 5-6, Protect Maintains the current system password. 6-7, Erase Clears the password. 9-10, Normal System attempts to boot using the BIOS stored in flash memory.
CMOS Jumper The jumper at pins 1, 2, and 3 controls whether settings stored in CMOS nonvolatile memory (NVRAM) are retained during a system reset. Procedure to restore the system’s CMOS and RTC to default values: 1. See “General Procedure to Change Jumper Setting” on page 116. 2. Move the CMOS jumper from pins 1 and 2 to pins 2 and 3 (the Clear CMOS memory position). 3. Reinstall the cover for your safety, and connect the power cord to the system. 4. Turn the system on.
Recovery Boot Jumper The jumper at pins 9, 10, and 11 controls whether the system attempts to boot using the BIOS programmed in the boot block area of the FLASH memory. This should be used only if the operational area of the BIOS is corrupted or needs to be upgraded. Contact your local service representative before doing this. Procedure to disable recovery booting: 1. See “General Procedure to Change Jumper Setting” on page 116. 2. Move the recovery boot jumper from pins 9 and 10 to pins 10 and 11. 3.
Procedure to permit boot block erasing and programming: 1. See “General Procedure to Change Jumper Setting” on page 116. 2. Move the boot block jumper from pins 13 and 14 to pins 14 and 15 to erase and program the BIOS boot block. 3. Reinstall the cover for your safety, and connect the power cord to the system. 4. Run the Boot Block Update Utility. 5. Turn off the system, and disconnect the power cord from the system. 6. Remove the cover. 7.
ISP2150 2U Rack Server Platform Product Guide
6 Product Regulation and Certification Information Regulatory Information Safety Compliance For Information Technology Equipment • • • • UL 1950 - CSA 950 (US/Canada) EN 60 950 (European Union) IEC60 950 (International) CE – Low Voltage Directive (73/23/EEC) (European Union) • EMKO-TSE (74-SEC) 207/94 (Nordics) EMC Compliance • • • • • • • • FCC (Class B) – Radiated & Conducted Emissions (USA) ICES-003 (Class B) – Radiated & Conducted Emissions (Canada) CISPR 22 (Class B) – Radiated & Conducted Emissio
Electromagnetic Compatibility Notices FCC Declaration of Conformity (USA) Product Type: BAR 2 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Intel Corporation 5200 N.E.
ICES-003 (Canada) Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée par le Ministre Canadian des Communications. (English translation of the notice above.
Lithium Battery Replacement Refer to technically qualified persons only for replacement of battery WARNING Danger of explosion if battery is incorrectly replaced. Replace with only the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.
Equipment Rack Precautions WARNINGS ANCHOR THE EQUIPMENT RACK: The equipment rack must be anchored to an unmovable support to prevent it from falling over when one or more servers are extended in front of it on slide assemblies. The anchors must be able to withstand a force of up to 113 kg (250 lbs). You must also consider the weight of any other device installed in the rack. MAIN AC POWER DISCONNECT: You are responsible for installing an AC power disconnect for the entire rack unit.
Cautions There are no user serviceable parts inside this product. Please refer to technically qualified service person. Use Only for Intended Applications This product was evaluated as Information Technology Equipment (ITE) that may be installed in offices, homes, schools, computer rooms and similar locations.
Warnings WARNING: English (US) AVERTISSEMENT: Français WARNUNG: Deutsch AVVERTENZA: Italiano ADVERTENCIAS: Español Product Regulation and Certification Information 127
WARNING: English (US) The power supply in this product contains no user-serviceable parts. There may be more than one supply in this product. Refer servicing only to qualified personnel. Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. A product with more than one power supply will have a separate AC power cord for each supply. The DC push-button on/off switch on the system does not turn off system AC power.
WARNING: English (US) (continued) A microprocessor and heat sink may be hot if the system has been running. Also, there may be sharp pins and edges on some board and chassis parts. Contact should be made with care. Consider wearing protective gloves. Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Dispose of used batteries according to manufacturer’s instructions.
AVERTISSEMENT: Français Le bloc d'alimentation de ce produit ne contient aucune pièce pouvant être réparée par l'utilisateur. Ce produit peut contenir plus d'un bloc d'alimentation. Veuillez contacter un technicien qualifié en cas de problème. Ne pas essayer d'utiliser ni modifier le câble d'alimentation CA fourni, s'il ne correspond pas exactement au type requis. Le nombre de câbles d'alimentation CA fournis correspond au nombre de blocs d'alimentation du produit.
AVERTISSEMENT: Français (suite) Le microprocesseur et le dissipateur de chaleur peuvent être chauds si le système a été sous tension. Faites également attention aux broches aiguës des cartes et aux bords tranchants du capot. Nous vous recommandons l'usage de gants de protection. Danger d'explosion si la batterie n'est pas remontée correctement. Remplacer uniquement avec une batterie du même type ou d'un type équivalent recommandé par le fabricant.
WARNUNG: Deutsch Benutzer können am Netzgerät dieses Produkts keine Reparaturen vornehmen. Das Produkt enthält möglicherweise mehrere Netzgeräte. Wartungsarbeiten müssen von qualifizierten Technikern ausgeführt werden. Versuchen Sie nicht, das mitgelieferte Netzkabel zu ändern oder zu verwenden, wenn es sich nicht genau um den erforderlichen Typ handelt. Ein Produkt mit mehreren Netzgeräten hat für jedes Netzgerät ein eigenes Netzkabel.
WARNUNG: Deutsch (Fortsetzung) Der Mikroprozessor und der Kühler sind möglicherweise erhitzt, wenn das System in Betrieb ist. Außerdem können einige Platinen und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie sollten Schutzhandschuhe tragen. Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden.
AVVERTENZA: Italiano Rivolgersi ad un tecnico specializzato per la riparazione dei componenti dell’alimentazione di questo prodotto. È possibile che il prodotto disponga di più fonti di alimentazione. Non modificare o utilizzare il cavo di alimentazione in c.a. fornito dal produttore, se non corrisponde esattamente al tipo richiesto. Ad ogni fonte di alimentazione corrisponde un cavo di alimentazione in c.a. separato.
AVVERTENZA: Italiano (continua) Se il sistema è stato a lungo in funzione, il microprocessore e il dissipatore di calore potrebbero essere surriscaldati. Fare attenzione alla presenza di piedini appuntiti e parti taglienti sulle schede e sul telaio. È consigliabile l'uso di guanti di protezione. Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore.
ADVERTENCIAS: Español El usuario debe abstenerse de manipular los componentes de la fuente de alimentación de este producto, cuya reparación debe dejarse exclusivamente en manos de personal técnico especializado. Puede que este producto disponga de más de una fuente de alimentación. No intente modificar ni usar el cable de alimentación de corriente alterna, si no corresponde exactamente con el tipo requerido.
ADVERTENCIAS: Español (continúa) Si el sistema ha estado en funcionamiento, el microprocesador y el disipador de calor pueden estar aún calientes. También conviene tener en cuenta que en el chasis o en el tablero puede haber piezas cortantes o punzantes. Por ello, se recomienda precaución y el uso de guantes protectores. Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo.
7 Equipment Log and Power Consumption Worksheets Equipment Log Use the blank equipment log provided here to record information about your system. You will need some of this information when you run the SSU.
Equipment Log (continued) Item Index Manufacturer Name and Model Number Serial Number Date Installed 139
Current Usage As an overall current usage limitation on the power supply, do not exceed a combined power output of 167 watts for the +5 and +3.3 volt outputs. The PCI slots on the server board are rated at a maximum of 5 amperes per slot. The maximum power allowed for each slot is 20 watts at +5 volts. The average current usage per slot should not exceed 3.0 amperes per slot; that is, 15 watts.
Worksheet, Calculating DC Power Usage 1. List the current for each board and device in the appropriate voltage level column. 2. Add the currents in each column. Then go to the next worksheet. Table 12. Power Usage Worksheet 1 Current (maximum) at voltage level: Device +3.3 V +5 V –5 V +12 V –12 V Server board 1.0 A 8.0 A 0.1 A 1.1 A 0.4 A Primary Processor Secondary Processor (if present) Terminator card, if no second processor 1.6 A Memory (four 128 MB DIMMs) 1.8 A 0.
ISP2150 2U Rack Server Platform Product Guide
Index A add-in board, sensitive to ESD, 26 Add-in boards IDE bus slots, 16 ISA, 68 PCI, 68 administrative password, 20 limiting access to SCU, 22 Advanced Menu, configuring in Setup, 58 audible beep error codes, 52 B Back Panel Connectors, 11 battery disposing of safely, 49 installing, 50 removing, 49 beep codes, 52 BIOS changing the language, 98 recovering, 97 upgrading, 95 BIOS update utility, 51 BMC, 18 boot block write protect default jumper, 118 Boot Device Priority menu, configuring, Setup, 66 Boot m
D diagnostics, preparing system for testing, 104 DIMM (memory), removing, 34 diskette drive controller, 17 enabling/disabling floppy writes, 22 installing drive in bay, 36 no booting in secure mode without password, 22 reconfiguring if cannot enter Setup, 53 removing bracket from drive, 35 removing drive from bay, 35 routing drive cable, 36 running SCU from, 51 E electrostatic discharge.
messages, error and informational, 110 monitoring server status, 18 mouse compatibility, 18 inactivity timer, 18 N-P network, controller, 9, 17 password, 21 administrative, 20 administrator, 21 entering to unblank screen, 22 retaining at system reset, 117 user, 20, 21 using to reactivate keyboard/mouse, 22 using to reactivate keyboard/mouse, 18 PCI embedded devices, 9 expansion slots, 9 slot current ratings, 140 PCI Configuration Menu, configuring in Setup, 58 PCI Device, Embedded SCSI menu, configuring in
diskette drive required to run SCU, 51 inactivity (lockout) timer, 18 secure mode, 21 affects boot sequence, 23 enter by setting passwords, 22 locking reset and power on/off switches, 22 no booting from diskette without password, 22 using hot keys to enter, 51 security, 22 boot sequence, 23 enabling/disabling floppy writes, 22 locking mouse, keyboard with timer, 18, 22 locking reset and power on/off switches, Setup, 22 password, 22 secure mode, 22 secure mode, setting in SCU, 21 unattended start, 23 using h
T-U termination board, removing, 31 timer keyboard or mouse inactive, 18 lockout (inactivity), setting in SCU, 18 upgrade Flash utility, 96 user password, 20 limit access to using system, 23 utilities BIOS update, 51 Emergency Management Port Console, 19, 79 Firmware update, 51, 98 FRUSDR load, 51 SCSI, 51 SCU, 51 Setup, 51, 53 Utilities, FRUSDR load utility, 92 V-W video blanking for security, 22 Index controller, 16 expansion, 16 memory, 9 resolutions supported, 16 video controller, 9 video memory, 16
ISP2150 2U Rack Server Platform Product Guide
