Intel® Server System SR1670HV Service Guide Intel Part Number: E74138-004 ® A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/Products
Disclaimer Disclaimer ® Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document.
Disclaimer
Preface Preface About this Manual Thank you for purchasing and using the Intel® Server System SR1670HV. This manual is written for system technicians who are responsible for troubleshooting, upgrading, and repairing this server system. This document provides a brief overview of the features of the board/chassis, a list of accessories or other components you may need, troubleshooting information, and instructions on how to add and replace components on the Intel® Server System SR1670HV.
Preface Additional Information and Software Documentation and software for this server product are available on the Intel Resource CD that shipped with your Intel server product. Software updates and additional information can be obtained at the following Intel web site: http://support.intel.
Contents Contents 1. Product Introduction...................................................................................... 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 System Package Contents............................................................................................. 1 System Features ............................................................................................................ 1 Front Panel Features ....................................................................................
Contents ® 5.2 5.3 5.1.5 Intel ICH10R SATA Port SW RAID Setting (3-pin RAID_SEL1) .................. 37 5.1.6 Force BIOS Recovery Setting (3-pin RECOVERY1)..................................... 38 Server Board Connectors............................................................................................. 39 5.2.1 Serial ATA Connectors (7-pin SATA1, SATA2, SATA3, SATA4) .................. 39 5.2.2 Internal USB Connectors (A-Type USB4; 5x1 pin USB3) ............................. 39 5.2.
Contents 8.5.5 Contact Information ..................................................................................... 106 9. Intel® Server Issue Report Form................................................................ 107 10. Getting Help ........................................................................................ 112 10.1 Warranty Information.................................................................................................. 112 11. Safety Information ................
Contents ATTENTION................................................................................................. 131 Información de seguridad del servidor ................................................................................ 132 Advertencias y precauciones sobre seguridad ................................................................... 132 Aplicaciones y usos previstos .............................................................................................
List of Figures List of Figures Figure 1. Server System Features ................................................................................................ 3 Figure 2. System Features – Back Panel ..................................................................................... 3 Figure 3. System Component Identification .................................................................................. 4 Figure 4. Server Node Connectors and Components..............................................
List of Figures Figure 48. Restoring the Chassis Cover ..................................................................................... 30 Figure 49. Screws On Hard Disk Drive Bay Module ................................................................... 30 Figure 50. Sliding the Hard Disk Drive Bay Module.................................................................... 30 Figure 51. Connected Cables and Backplane Expose ............................................................... 31 Figure 52.
List of Figures Figure 98. Intel VT-d Configuration Menu................................................................................... 65 Figure 99. Legacy Device Configuration Menu........................................................................... 65 Figure 100. USB Configuration Menu ......................................................................................... 66 Figure 101. PCIPnP Configuration Menu.................................................................................
List of Figures Figure 148. Insert Driver Disk Screen......................................................................................... 97 Figure 149. More Driver Disks? Screen...................................................................................... 97 Figure 150. Selecting the SuSe* Installation............................................................................... 98 Figure 151. Initializing the SuSe* Installation................................................................
List of Tables List of Tables Table 1. System Package Contents List ....................................................................................... 1 Table 2. System Feature Set ........................................................................................................ 1 Table 3. Server Node Connectors and Components Descriptions ............................................... 6 Table 4. Front Panel LEDs Descriptions......................................................................
List of Tables
Product Introduction 1. Product Introduction This chapter briefly describes the main features of the Intel® Server System SR1670HV. 1.1 System Package Contents Check your system package for the following items. Table 1. System Package Contents List Model Name Intel® Server System SR1670HV Integrated System Components 2 x Intel® Server Board S5500HV 2 x 770-W Single Power Supplies (non-redundant) 8 x Hot-swap 2.
Product Introduction Feature Description On-board I/O Per Server Node: 1 x External DB-9 Serial Port 2 x RJ-45 LAN ports (stacked) 1 x RJ-45 Management LAN port 3 x USB 2.0 ports (Front x 1, Rear x 2) 1 x Internal A-type USB Port 1 x VGA port System Fan Support Eight 4-pin managed system fan.
Product Introduction System ID LED System ID Button Figure 1. Server System Features 1.4 Rear Panel Features You can find the following features on the server system back panel: Dual tool-less cold-swap, non-redundant power supplies—one for each installed server node. Add-in card slot covers for each installed server node. External I/O ports for each installed server node. Figure 2. System Features – Back Panel 1.
Product Introduction Power Supply Modules Riser Card Riser Card Server Node 1 Server Node 2 4 x System Fans Node 2 4 x System Fans Node 1 Hard Disk Drive Bay Module Figure 3. System Component Identification The following figure identifies connectors and major components of each server node.
Product Introduction A B C Q D P O N E M L F K G G H H I I J Figure 4.
Product Introduction Table 3. Server Node Connectors and Components Descriptions Description Description A Rear I/O Connectors K CPU 1 DIMM Slots (Slots A1– C2) B BMC Management Module connector L Peripheral Drive Power Connector – 4 pin C SATA Ports 1-4 M CPU 2 - LGA 1366 Socket D Internal USB(4) 2.
Product Introduction 1.6.2 RJ-45 LAN Ports 1 and 2 LEDs Figure 6. RJ-45 Ports 1 and 2 LEDs Table 5. RJ-45 Ports 1 and 2 LEDs Descriptions ACT/LINK LED Status 1.6.3 SPEED LED Description Status Description OFF No link OFF 10 Mbps connection GREEN Linked Orange 100 Mbps connection BLINKING Data activity Green 1 Gbps connection HDD Status LED Figure 7. HDD Status LED Table 6.
Product Introduction Figure 8. Cable Connections 1.7.1 1. 2. 3. 4. 5. 6. 7.
Hardware Setup 2. Hardware Setup 2.1 Chassis Cover 2.1.1 Removing the Chassis Cover 1. Loosen the two thumbscrews on the read panel to release the rear cover from the chassis. Figure 9. Rear Panel Thumbscrews 2. Firmly hold the cover and slide it toward the rear panel for about half an inch until disengages from the chassis. Figure 10. Sliding the Chassis Cover 3. Lift the cover from the chassis. 2.
Hardware Setup your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/server board components. The PnP cap should be retained and re-used if the server is ever returned for service. The product warranty does not cover damage to the socket contacts resulting from incorrect processor installation/removal, or misplacement/loss/incorrect removal of the PnP cap. 2.2.1 Installing the Processor To install a processor: 1.
Hardware Setup Figure 12. Retention Tab and Load Lever 3. Lift the load lever in the direction of the arrow to a 135° angle. Figure 13. Load Plate 4. Lift the load plate with your thumb and forefinger to a 100° angle. 5. Remove the PnP cap from the processor socket. Figure 14. PnP Cap 6. Position the processor over the socket, making sure the gold triangle is on the bottomleft corner of the socket, and then fit the socket alignment key into the processor notch.
Hardware Setup Figure 15. CPU Notch and Alignment Key 7. (Skip this step if your heatsink has pre-applied thermal interface material.) Apply several drops of thermal paste to the exposed area of the processor the heatsink will be in contact with, ensuring it is spread in an even, thin layer. Figure 16. Applying Thermal Paste NOTE: The processor fits in only one correct orientation.
Hardware Setup Figure 17. Closing the Load Plate 2.2.2 Installing the Processor Heatsink You must install the processor before installing the heatsink. Improper installation can damage the heatsink. Pay close attention to the steps and perform each step exactly as indicated to avoid damage. The heatsink has Thermal Interface Material (TIM) located on the bottom of it. Use caution when you unpack the heatsink so you do not damage the TIM. New unused heatsinks have adequate TIM on the bottom.
Hardware Setup 3 w lo rF Ai 2 1 4 TIM sis as Ch Fr t on AF002841 Figure 18. Installing the Heatsink (Passive Heatsink Shown) 2.2.3 Removing the Processor Heatsink To remove or replace a processor, you must first remove the heatsink. CAUTION Improper removal can damage the heatsink. Pay close attention to the steps and perform each step exactly as indicated to avoid damage. To remove the heatsink, follow these steps: 1.
Hardware Setup Figure 19. Removing the Heatsink NOTE: Tighten the four heatsink screws in a diagonal sequence. 2.3 System Memory 2.3.1 Overview Each installed server node supports twelve (12) DDR3 DIMM sockets—six for each installed processor. NOTE: You should only install memory in DIMM sockets DIMM_D1 through DIMM_F2 when dual processors are installed on a given server node. On a given server node, DIMM sockets DIMM_D1 through DIMM_F2 are not enabled in single processor configurations.
Hardware Setup Figure 20. DDR3 DIMM Sockets Location 2.3.
Hardware Setup 2.3.2.1.1 Memory Population Rules DIMM population requirements are dependent upon the number of slots per channel; number of DIMMs installed; and rank type. When installing memory, consider the following: Populate DIMMs by channel starting with the blue slot farthest from the CPU. All channels in a system will run at the fastest common frequency. RDIMMs and UDIMMs cannot be mixed.
Hardware Setup When installing DIMMs, you must follow the following population rules to deliver the best performance: Maximize number of channels populated first Balanced DIMM population across channels and sockets. Table 10.
Hardware Setup Figure 21. Unlocked Retaining Clips TIP A DIMM is keyed with a notch so that it fits in only one direction. To avoid damaging the DIMM, DO NOT force a DIMM into a socket. 3. Firmly insert the DIMM into the socket until the retaining clips snap back into place and the DIMM is properly seated. Figure 22. Locked Retaining Clips 2.3.4 Removing a DIMM Follow these steps to remove a DIMM: 1.
Hardware Setup 2.4 Installing a PCI Express* Add-In Card to the Riser Bracket The system comes with a riser card bracket for each installed server node. To install a PCI Express* add-in card, you must remove the bracket assembly from the server using the following procedure: To install a PCI Express* add-in card: 1. Firmly hold the riser card bracket, and then pull it up to detach it from the riser slot on the server board. Figure 24. Riser Card Bracket 2.
Hardware Setup Figure 27. Pressing Rising Card Bracket for Golden Connectors to Fit 5. If applicable, connect the cable(s) to the card.
Hardware Setup 2.5 Installing the BMC Management Module Complete the following steps to install the BMC Management Module onto the server board. 1. Locate the BMC_FW1 header on the server board. Figure 28. BMC_FW1 Header 2. Orient and press the management card in place. Figure 29. Orienting the Management Module Card 3. Insert the LAN cable plug into the Server Management LAN port located above the USB ports. Figure 30.
Hardware Setup 2.6 Hard Disk Drives The system supports up to eight hot-swap 2.5-inch SATAII/SAS hard disk drives—four for each installed server node. Each installed hard disk is mounted to a drive tray. When inserted into a drive bay, the hard drive is blind-mated to a matching connector on a backplane, which is either cabled to SATA ports on each server node (default) or can be routed to add-in SAS/SAS RAID cards. The hard drives for each server node are numbered as follows: 3 4 2 1 Figure 31.
Hardware Setup Figure 34. Pushing the Tray Lever 6. Repeat Steps 1 through 5 to add additional hard drives to the system.
Installing the Rackmount Rail Kit 3. Installing the Rackmount Rail Kit Your rackmount rail kit package contains: Two pairs of server rails (for the server) Two pairs of rack rails (for the rack) Nut-and-bolt type screws Figure 35. Rackmount Rail Kit Items Figure 36. Screw positions on the rail 3.1 Attaching the Rails to the Server To attach the server rails: 1.
Installing the Rackmount Rail Kit Figure 37. Attaching the Front End of the Server Rail to Side of Chassis 2. Attach the rear end of the server rail to the side of the chassis, matching each of the two hooks to the hooks to the holes on the rail, and then slide the rail towards the front panel until it locks into place. Figure 38. Sliding the Server Rail 3. Secure the server rail to the side of the chassis with two screws. Figure 39. Securing the Server Rail With Screws 4.
Installing the Rackmount Rail Kit Figure 40. Positioning the Rack Rail to 1U Space on Rack 7. Secure the front end of the rail with two rack screws. 8. Secure the rear end of the rail with two rack screws. 9. Repeat steps 5 through 8 to assemble and attach the second rail. 3.3 Rackmounting the Server To mount the server to the rack: 1. Align the server rails with the rack rails, and then push the server all the way to the depth of the rack. 2.
System Service 4. System Service 4.1 Replacing Power Supply Units (PSUs) Complete the following steps to replace a failed power supply unit (PSU). NOTE: Installed power supply units (PSUs) provide no power redundancy. A failed PSU will bring down the respective server node. You can cold-swap the failed PSU while the other power supply unit is still functional. To replace the failed PSU: 1. Disconnect the power cord. 2. Hold the PSU lever and press the PSU latch. Figure 42.
System Service 4.2 Replacing System Fans To uninstall the system fans: CAUTION Verify the system is powered off before removing any system fan from the system. The system fans operate at very high speeds and may cause serious injury. 1. Disconnect the system fan cable from the fan connector on the server board. Figure 45. Disconnecting System Fan Cable 2. Lift the fan and set it aside. Figure 46. Lifting System Fan 3. Repeat Steps 1 and 2 to uninstall other system fans. To reinstall a system fan: 1.
System Service 3. Reinstall the chassis cover. Press down gently on the location above the system fans to ensure proper fan installation as shown in the following figure. Figure 48. Restoring the Chassis Cover 4.3 SATA/SAS BackPlane Replacement The system includes a single SATA/SAS backplane that is mounted to the back side of the hard disk drive (HDD) bay module. You can replace the backplane replacement by performing the following procedure: 1. Remove the system top cover. 2.
System Service 5. Carefully rotate back and place the connected HDD bay module on top of the system fan assembly so all connected cables and backplane are exposed. Figure 51. Connected Cables and Backplane Expose 6. Note the location and connector type of each cable you must disconnect from the backplane. Disconnect all cables from the backplane and remove the bundled cables from the latched plastic cable holders. 7. Place the HDD bay module onto a static-free surface. 8.
System Service 13. Carefully reposition the backplane over the guide pins on each side of the hard drive bay. Verify that all of the front panel cables are located completely within the open area behind the backplane. 14. Securely fasten all 12 screws into the backplane. Be careful not to overtighten them. 15. Reposition the hard drive bay module over the system fan assembly and reconnect all cables to the backplane. Reposition cable bundles within plastic cable holders. Figure 53.
System Service Figure 55. Aligning the Module with the Alignment Slots on the Chassis 17. Slide the hard drive bay module back until the screw holes are aligned. 18. Secure the HDD bay module to the chassis using the six screws, three on each side. 19. Install the hard drives into the same position from which they were removed. 4.
System Service Figure 57 Control Panel Module Top view 4. Carefully detach each cable pair from both control panel boards. 5. Place the detached Control Panel module onto an anti-static surface. Figure 58 Detached Control Panel Module 6. Take out the faulty Control Panel board by removing the three screws that attach it to the module tray. 7.
Jumpers, Connectors, and LEDs 5. Jumpers, Connectors, and LEDs 5.1 Configuration and Support Jumpers 5.1.1 Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which includes system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord.
Jumpers, Connectors, and LEDs 5.1.2 VGA Controller Setting (3-pin VGA_SW1) This jumper allows you to enable or disable the onboard VGA controller. Set to pins 1–2 to activate the VGA feature. Figure 60. VGA Controller Setting 5.1.3 DDR3 Voltage Control Setting (4-pin LVDDR3_SEL1, LVDDR3_SEL2) The server board provides DDR3 voltage control jumper blocks for each CPU bank of memory.
Jumpers, Connectors, and LEDs Figure 61. DDR3 Voltage Control Setting 5.1.4 LAN Controller Setting (3-poin LAN_SW1, LAN_SW2) These jumpers allow you to enable or disable the onboard Intel® 82574LGigabit LAN controllers. Set to pins 1-2 to activate the Gigabit LAN feature. Figure 62. LAN Controller Setting 5.1.5 Intel® ICH10R SATA Port SW RAID Setting (3-pin RAID_SEL1) This jumper allows you to select the Serial ATA RAID configuration utility to use when you create disk arrays.
Jumpers, Connectors, and LEDs Figure 63. Intel® ICH10R SATA Port SW RAID Setting 5.1.6 Force BIOS Recovery Setting (3-pin RECOVERY1) This jumper allows you to quickly update or recover the BIOS settings when it becomes corrupted. To update the BIOS: 1. Prepare a USB flash disk that contains the original or latest BIOS for the server board (XXXXXX.ROM) and the AFUDOS.EXE utility. 2. Set the jumper to pins 2–3. 3. Insert the USB flash and turn on the system to update the BIOS. 4. Shut down the system. 5.
Jumpers, Connectors, and LEDs 5.2 Server Board Connectors 5.2.1 Serial ATA Connectors (7-pin SATA1, SATA2, SATA3, SATA4) Supported by the Intel® ICH10R chipset, these connectors are for the Serial ATA signal cables for Serial ATA hard disk drives that allow up to 3 Gb/s of data transfer rate. Figure 65. SATA Connectors 5.2.2 Internal USB Connectors (A-Type USB4; 5x1 pin USB3) These connectors are for USB 2.0 ports.
Jumpers, Connectors, and LEDs 5.2.3 System Fan Connectors (4-pin FRNT_FAN1, FRNT_FAN2, FRNT_FAN3, FRNT_FAN4) The system fan connectors support cooling fans of 350 mA–740 mA (8.88 W max.) or a total of 3.15 A–6.66 A (53.28 W max.) at +12V. Connect the fan cables to the fan connectors on the server board, ensuring the black wire of each cable matches the ground pin of the connector. CAUTION DO NOT forget to connect the fan cables to the fan connectors.
Jumpers, Connectors, and LEDs 5.2.5 BMC Management Module Header (BMC_FW1) The BMC connector on the server board supports a BMC Management Module. Figure 69. BMC Management Module Header 5.2.6 Power Supply SMBus Connectors (6x1 pin JP1, JP2) These connectors allow you to connect SMBus (System Management Bus) to the power supply unit to read PSU information. Devices communicate with a SMBus host and/or other SMBus devices using the SMBus interface. Figure 70.
Jumpers, Connectors, and LEDs 5.2.7 Main Power Connectors (20-pin PWR1, 20-pin PWR2) The server board provides dual 20-pin ATX Main Power connectors. Both connectors have identical pin-outs and are not used concurrently. Figure 71. Main Power Connectors 5.2.8 Peripheral Power Connector (4-pin PWR3) +5V GND GND +12 V The server board provides a 4-pin peripheral power connector. This connector can supply power as needed to add-in peripheral devices such as hard drives or optical drives.
Jumpers, Connectors, and LEDs Figure 73. System Panel Connector 5.2.9.1 System power LED (3-pin PLED) This 3-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power and blinks when the system is in sleep mode. 5.2.9.2 System Message LED (2-pin MLED) This 2-pin connector is for the message LED cable that connects to the front message LED.
Jumpers, Connectors, and LEDs 5.2.10 Auxiliary Panel Connector (20-pin AUX_PANEL1) This connector is for additional front panel features including front panel SMB, locator LED and switch, chassis intrusion, and LAN LEDs. Figure 74. Auxiliary Panel Connector 5.2.10.1 Front panel SMB (6-1 pin FPSMB) These leads connect the front panel SMBus cable. 5.2.10.2 LAN activity LED (2-pin LAN1_LED, LAN2_LED) These leads are for Gigabit LAN activity LEDs on the front panel. 5.2.10.
Jumpers, Connectors, and LEDs 5.3 Internal LEDs 5.3.1 Standby Power LED The server board comes with a standby power LED. The green LED lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any server board component. The following illustration shows the location of the onboard LED. Figure 75. Standby Power LED 5.3.
Jumpers, Connectors, and LEDs 5.3.3 System Identification LED The server board includes a System ID LED. This LED illuminates when the System ID button on the front panel is pushed. This LED is used to identify the system when servicing is required in a racked environment. Figure 77. System Identification LED NOTE: The blue system ID LED will turn on when plug power cord until the BMC reset complete. 5.3.4 BMC LED (BMC_LED1) The server board includes a BMC LED.
BIOS Updates and Configuration 6. BIOS Updates and Configuration Your server system includes a BIOS which is used to configure critical system settings, ensuring best performance and reliability. In addition, it provides options that you can manually set to configure system features and functions to best meet custom operating environments.
BIOS Updates and Configuration Figure 79. Updating the BIOS in DOS NOTE: DO NOT turn off the system or interrupt the BIOS update process. Doing so corrupts the BIOS and prevents your system from booting up. If your BIOS becomes corrupted for any reason, you must read and complete the BIOS Recovery Process described later in this section. 4. When the BIOS Update has completed successfully, you must reboot the system for the changes to take effect. 5.
BIOS Updates and Configuration Figure 80. Recovering the BIOS Using the Force BIOS Update Jumper 5. Plug in the USB flash drive and power on the system. The BIOS update process begins automatically. 6. When the BIOS update has completed successfully, power down the system. 7. Set the Force BIOS Update jumper back to its default position. 8. Re-install the system top cover. 9. Power on the system and access the BIOS Setup utility . 10. Hit the key to load BIOS Setting Defaults. 11.
BIOS Updates and Configuration NOTE: Should the system operate in an undesired manner after making BIOS setting changes, default settings should be restored by either selecting the “Load Setup Defaults” option in the Exit Menu, or by hitting the key anytime while in the BIOS Setup Utility. 6.3.1 Accessing BIOS Setup Utility The embedded BIOS Setup Utility is accessed by pressing the key while the system is conducting its Power-On Self Test (POST).
BIOS Updates and Configuration Server: Provides sub-menus used to view/change IPMI and Remote Connectivity options. Boot: Provides sub-menus used to view/change system boot options and system security. Exit: Provides utility exit options and an option to load BIOS option default settings. 6.3.2.2 Navigation Keys At the bottom-right corner of a menu screen are the navigation keys for that particular menu. Use the navigation keys to select items in the menu and change the settings. 6.3.2.
BIOS Updates and Configuration Figure 83. Main Menu 6.3.3.1 System Time [xx/xx/xxxx] This option displays and gives the option to change the system time. 6.3.3.2 System Date [Day xx/xx/xxxx] This option displays and gives the option to change the system date. 6.3.3.3 SATA 1-4 Sub-Menus These fields display devices that BIOS automatically detected as attached to the on-board SATA ports. A separate sub-menu is available to view/configure each detected device.
BIOS Updates and Configuration Mode, PIO Mode, Async DMA, Ultra DMA, and S.M.A.R.T. monitoring. These values are not user-configurable. If no device is detected on the selected SATA port, these fields display N/A. 6.3.3.3.1 LBA/Large Mode [Auto] Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA mode disabled. Configuration options: [Disabled] [Auto] 6.3.3.3.
BIOS Updates and Configuration Figure 85. IDE Configuration Menu 6.3.3.4.1 SATA Configuration [Enhanced] Configuration options: [Disabled] [Compatible] [Enhanced] Configure SATA as [IDE] Sets the configuration for the Serial ATA connectors supported by the Southbridge chip. Configuration options: [IDE] [RAID] [AHCI] TIPS If you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices, keep the default setting [IDE].
BIOS Updates and Configuration Figure 86. AHCI Configuration Menu 6.3.3.5.1 AHCI CD/DVD Boot Time out [35] Selects the boot time out value for SATA CD/DVD devices in AHCI mode. Configuration options: [0] [5] [10] [15] [20] [25] [30] [35] 6.3.3.5.2 SATA Port1-4 [XXXX] Displays the status of auto-detection of SATA devices. Figure 87. Status of Auto-Detection of SATA Devices Menu 6.3.3.5.3 SATA Port0 [Auto] Allows you to select the type of device connected to the system.
BIOS Updates and Configuration 6.3.3.6 System Information Sub-Menu This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. Figure 88. System Information Menu OS SETUP UTILITY 6.3.3.6.1 AMIBIOS Displays the auto-detected BIOS information. 6.3.3.6.2 Processor Displays the auto-detected processor information. 6.3.3.6.3 System Memory Displays the total system memory detected. 6.3.3.6.
BIOS Updates and Configuration 6.3.4 Advanced Menu The Advanced menu items are used to view/change server sub-system options. CAUTION Intel strongly suggests having only qualified persons with in-depth knowledge of processor and chipset features make changes to the options available in the Advanced Menu. Incorrectly setting many of the options available within these sub-menus can negatively impact the operation of the server. Intel recommends using default settings whenever possible.
BIOS Updates and Configuration Figure 91. CPU Configuration Menu Scroll down for more items. Figure 92. CPU Configuration Menu, Continued 6.3.4.1.1 C1E Support [Enabled] Allows you to enable or disable Enhanced Halt State support. Configuration options: [Disabled] [Enabled] 6.3.4.1.2 Hardware Prefetcher [Enabled] Allows you to enable or disable the Hardware Prefetcher function. Configuration options: [Disabled] [Enabled] 6.3.4.1.
BIOS Updates and Configuration 6.3.4.1.4 ® Intel Virtualization Tech [Enabled] The Intel® Virtualization Technology allows a hardware platform to run multiple operating systems separately and simultaneously, enabling one system to virtually function as several systems. Configuration options: [Disabled] [Enabled] 6.3.4.1.5 CPU TM Function [Enabled] This function enables the overheated CPU to throttle the clock speed to cool down. Configuration options: [Disabled] [Enabled] 6.3.4.1.
BIOS Updates and Configuration Configuration options: [Disabled] [Enabled] 6.3.4.1.14 ® Intel C-STATE Tech [Enabled] The Intel® C-State Technology allows the CPU to save more power under idle mode. Enable this item only when you install a C-State Technology-supported CPU. Configuration options: [Disabled] [Enabled] 6.3.4.1.15 C3 State [ACPI C3] Allows you to select the CPU action under C3 state. Configuration options: [Disabled] [ACPI C2] [ACPI C3] 6.3.4.1.
BIOS Updates and Configuration Figure 93. Chipset Configuration Menu 6.3.4.3 CPU Bridge Chipset Configuration Sub-Menu Figure 94. CPU Bridge Chipset Configuration Menu Scroll down for more items.
BIOS Updates and Configuration Figure 95. CPU Bridge Chipset Configuration Menu, Continued 6.3.4.3.1 CSI Links Speed [Full-Speed] Allows you to set the speed of CSI Links. Configuration options: [Slow-Mode] [Full-Speed] 6.3.4.3.2 CSI Frequency [Auto] Allows you to set the CSI frequency. Configuration options: [Auto] [4.800GT] [5.866GT] [6.400GT] 6.3.4.3.3 CSI Isochronous [Disabled] Configuration options: [Disabled] [Enabled] 6.3.4.3.
BIOS Updates and Configuration 6.3.4.3.11 Demand Scrubbing [Enabled] Enables or disables the ECC demand scrub. Configuration options: [Disabled] [Enabled] 6.3.4.3.12 Patrol Scrubbing [Disabled] Enables or disables the ECC patrol scrub. Configuration options: [Disabled] [Enabled] 6.3.4.3.13 NUMA Aware [Auto] Configuration options: [Disabled] [Enabled] 6.3.4.3.14 Page Policy [Closed] Configuration options: [Closed] [Open] 6.3.4.3.
BIOS Updates and Configuration NOTE: You should not change the following memory throttling settings from their defaults unless extensive performance benchmarking tests were conducted validating the changes. Making uninformed changes can negatively affect system performance. 6.3.4.3.21 Inlet Temperature [28] Configuration options: [25] [28] [30] [35] 6.3.4.3.22 Temperature Rise to DIMM [10] Configuration options: [0] [5] [10] [15] 6.3.4.3.23 Air Flow Velocity (M/s) [2] Configuration options: [0.
BIOS Updates and Configuration 6.3.4.5.2 USB Port Configure [8+4 USB Ports] This item disappears when you set the USB Functions item to [Disabled]. Configuration options: [6+6 USB Ports] [8+4 USB Ports] 6.3.4.5.3 USB 2.0 Controller [Enabled] Allows you to enable or disable the USB 2.0 controller. This item becomes unconfigurable if you set the USB Functions item to [10 USB Ports] or [12 USB Ports]. Configuration options: [Enabled] [Disabled] 6.3.4.5.4 SLP_S4# Min.
BIOS Updates and Configuration 6.3.4.7.1 Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address. Configuration options: [Disabled] [3F8/IRQ4] [3E8/IRQ4] [2E8/IRQ3] 6.3.4.7.2 Serial Port2 Address [2F8/IRQ3] Allows you to select the Serial Port2 base address. Configuration options: [Disabled] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3] 6.3.4.8 USB Configuration Sub-Menu Figure 100. USB Configuration Menu TIP The following item appears only when you set USB Function to [Enabled]. 6.3.
BIOS Updates and Configuration 6.3.4.8.3 BIOS EHCI Hand-Off [Enabled] Enables or disables the BIOS EHCI hand-off support. Configuration options: [Disabled] [Enabled] 6.3.4.9 PCIPnP Configuration Sub-Menu The PCIPnP Configuration menu items allow you to change the advanced settings for PCI/PnP devices. CAUTION Take caution when changing the settings of the PCI/PnP Configuration menu items. Incorrect field values can cause the system to malfunction. Figure 101. PCIPnP Configuration Menu 6.3.4.9.
BIOS Updates and Configuration 6.3.4.9.3 Onboard Option ROM Priority [High] Allows you to select the onboard option ROM priority. Configuration options: [Normal] [High] 6.3.4.9.4 Onboard LAN1/2 Boot [PXE] Allows you to configure the boot mode for onboard LAN ports 1 and 2. Configuration: [Disabled] [PXE] [iSCSI] 6.3.4.10 Power On Configuration Sub-Menu Figure 102. Power On Configuration Menu 6.3.4.10.
BIOS Updates and Configuration NOTE: The following items appear only when the Resume On RTC Alarm item is set to [Enabled]. 6.3.4.10.5 RTC Alarm Date [15] To set the alarm date, highlight this item and press the <+> or <-> key to make the selection. 6.3.4.10.6 System Time [12:30:30] Use the , or key to select a field. Use the <+> or <-> key to configure alarm time. 6.3.4.11 Event Log Configuration Sub-Menu Figure 103. Event Log Configuration Menu 6.3.4.11.
BIOS Updates and Configuration 6.3.4.12 Hardware Monitor Sub-Menu Figure 104. Hardware Monitor Configuration Menu Scroll down for more items. Figure 105. Hardware Monitor Configuration Menu, Continued 6.3.4.12.1 CPU1/2 Temperature [xxx°C/xxx°F] The onboard hardware monitor automatically detects and displays the processor temperatures. Select [Ignored] if you do not want to display the detected temperatures. 6.3.4.12.
BIOS Updates and Configuration 6.3.4.13 6.3.4.13.1 I/O Virtualization Sub-Menu SR-IOV Supported [Disabled] Configuration options: [Enable] [Disabled] 6.3.4.14 PCI Express* Configuration Sub-Menu Figure 106. PCI Express* Configuration Menu 6.3.4.14.1 Active State Power-Management [Disabled] Enables or disables the PCI Express* L0s and L1 link power states. Configuration options: [Disabled] [Enabled] 6.3.4.15 ACPI Configuration Sub-Menu Figure 107.
BIOS Updates and Configuration 6.3.4.15.1 Advanced ACPI Configuration Sub-Menu Figure 108. Advanced ACPI Configuration Menu 6.3.4.15.2 ACPI 2.0 Support [Enabled] Specifies the Advanced Configuration and Power Interface (ACPI) version supported. Configuration options: [Disabled] [Enabled] 6.3.4.15.3 ACPI APIC Support [Enabled] Allows you to enable or disable the Advanced Configuration and Power Interface (ACPI) support in the Advanced Programmable Interrupt Controller (APIC).
BIOS Updates and Configuration 6.3.4.15.9 High Performance Event Timer [Enabled] Allows you to enable or disable the High Performance Event Timer feature. Configuration options: [Disabled] [Enabled] 6.3.4.15.10 HPET Memory Address [FED00000h] Configuration options: [FED00000h] [FED01000h] [FED002000h] [FED03000h] 6.3.4.16 General WHEA Configuration Sub-Menu Figure 110. General WHEA Configuration Menu 6.3.4.16.
BIOS Updates and Configuration 6.3.5.1.1 BMC Firmware Version: #.## Displays the BMC Firmware version of the BMC Management Module. 6.3.5.1.2 Set LAN# Configuration Two sub-menus used to configure on-board LAN Port 1 and the Server Management LAN Port (LAN Port 3) for Serial-over-LAN support. Configurable LAN parameters in both these sub-menus include: IP Address Source [DHCP Mode/Static Mode] IP Address [000.000.000.000] Subnet Mask [000.000.000.000] Gateway Address [000.000.000.000] 6.3.5.1.
BIOS Updates and Configuration 6.3.5.2.2 Serial port number [COM2] Selects the serial port for console redirection. Configuration options: [COM1] [COM2] 6.3.5.2.3 Base Address. IRQ [2F8h, 3] This item is not user-configurable and changes with the configuration of Serial port number. 6.3.5.2.4 Serial port Mode [57600 8,n,1] Sets the Serial port mode. Configuration options: [115200 8,n,1] [57600 8,n,1] [38400 8,n,1] [19200 8,n,1] [09600 8,n,1] 6.3.5.2.
BIOS Updates and Configuration Figure 113. Boot Menu 6.3.6.1 Boot Device Priority Figure 114. Boot Device Priority Menu 6.3.6.1.1 1st ~ xxth Boot Device [XXXXXXX] These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system. Configuration options: [xxxxx Drive] [Disabled] 6.3.6.
BIOS Updates and Configuration 6.3.6.3 Boot Settings Configuration Options in this sub-menu allow you to configure how the system should operate during the system boot process. Figure 115. Boot Settings Configuration Menu 6.3.6.3.1 Quick Boot [Enabled] Enabling this item allows the BIOS to skip some power-on self tests while booting, to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items. Configuration options: [Disabled] [Enabled] 6.3.6.3.
BIOS Updates and Configuration Configuration options: [Disabled] [Enabled] 6.3.6.3.7 Interrupt 19 Capture [Enabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 6.3.6.4 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options. Figure 116.
BIOS Updates and Configuration NOTE: If you forget your BIOS password, you can clear it by erasing the CMOS Real-Time Clock (RTC) RAM. For information on how to erase the RTC RAM, refer to the “Configuration and Support Jumpers” section. Once a Supervisor password is set, other system security options will display on the screen. Figure 117. Security Menu After Supervisor Password is Set 6.3.6.4.
BIOS Updates and Configuration 6.3.7 Exit Menu Options in the Exit menu allow you to Save or Discard current changes made to the BIOS settings. Another option restores all BIOS setting defaults. Figure 118. Exit Menu 6.3.7.1 Exit & Save Changes Once you finish making BIOS changes, select this option to ensure the settings are saved to the CMOS RAM. When you select this option, a confirmation window displays. Select YES to save changes and Exit. The system will automatically reboot. 6.3.7.
Embedded SATA RAID 7. Embedded SATA RAID This section provides an overview of the SATA Software RAID options embedded on the server board. It describes how to enable the RAID feature and configure RAID sets using either of the two SW RAID Configuration Utilities. For more in-depth RAID information including definitions, setup, and support, refer to the respective SATA SW RAID Users Guides included on the System Resource CD, or download them from the following Intel website: http://support.intel.
Embedded SATA RAID 7.2 Enabling RAID in the BIOS Setup By default, the BIOS does not enable RAID support. To enable this feature, you must set an option in the BIOS setup as described in the following procedure: 1. 2. 3. 4. Enter the BIOS Setup (F2 Key) during POST. Go to the MAIN menu, select IDE Configuration and press Set the Configure SATA As option to [RAID]. Save your changes and then exit BIOS Setup. 7.
Embedded SATA RAID Figure 120. POST screen showing LSI* MegaRAID Option ROM display The following screen displays: Figure 121. Utility Main Window At the bottom of the screen is the legend box. The keys on the legend box allow you to navigate through the setup menu options or execute commands. The keys on the legend box vary according to the menu level. 3. Select Configure. 7.3.1.
Embedded SATA RAID Figure 122. Configuration Menu Options The ARRAY SELECTION MENU displays the drives connected to the SATA ports. 2. Use the up/down arrow key and key to select each drive you want to include in the RAID set. As each drive is selected, the drive indicator changes from READY to ONLIN A[X]-[Y], where X is the array number, and Y is the drive number. Figure 123.
Embedded SATA RAID Figure 124. Selecting the Configurable Array on Easy Configuration Menu 4. Press again, the virtual drive information appears including a Virtual Drive menu that allows you to change the virtual drive parameters. Figure 125. Virtual Drive Menu 5. Select RAID from the Virtual Drive sub-menu, and then press . 6. Select the RAID level from the menu, and then press .
Embedded SATA RAID Figure 126. Selecting the RAID Level 7. When creating a RAID 1 or a RAID 10 set, select DWC from the Virtual Drive menu, and then press . 8. Select On to enable the Disk Write Cache setting, and then press . Figure 127. Enabling the Disk Write Cache Setting NOTE: Enabling DWC can improve performance, but with the risk of data loss. If the New Configuration option was selected from the Configuration Menu, you have the option to define the virtual drive size.
Embedded SATA RAID 12. When prompted to save configuration, select Yes from the menu, and then press . Figure 129. Completing RAID Configuration After creating RAID set(s), you must initialize the virtual drives. You can initialize the virtual drives using the Initialize from the Management Menu. 1. From the Management Menu, select Initialize, and then press . Figure 130.
Embedded SATA RAID Figure 131. Virtual Drives (Selection) Pulldown Menu 3. Press to start initialization. When prompted, select Yes from the Initialize? Dialog box, and then press . Figure 132. Initialize Confirmation Dialog Box WARNING Initializing a virtual drive erases all data on the drive. A progress bar displays on screen. If necessary, pressing the key can be used to stop the initialization process. 4. When initialization is completed, press .
Embedded SATA RAID Figure 133. Initialization Progress Bar 7.3.1.3 Enabling WriteCache To improve performance, you have the option to enable the Write Cache feature of the RAID controller. WARNING When the WriteCache option is Enabled, data may be lost in the event of a power failure. TIP The Write Cache feature is recommended for RAID 1 and RAID 10 sets. To enable Write Cache: 1. From the Management Menu, select Objects > Adapter, and then press to display the adapter properties. 2.
Embedded SATA RAID 7.3.2 Intel® Matrix Storage Manager Configuration Utility NOTE: Follow the procedures in this section only if the server board is configured to support the Intel® Matrix Storage Manager RAID option. Otherwise, refer to the section describing the LSI* SATA Software RAID Utility. This section provides an overview of how to setup a RAID set using SATA hard disk drives attached to the on-board SATA ports of the server board.
Embedded SATA RAID Figure 136. Create RAID Volume Menu 2. Enter a name for the RAID set and press . 3. When the RAID Level option is selected, press the up/down arrow key to select a RAID level to create, and then press . 4. When the Disks option is selected, press to select the hard disk drives you want to include in the RAID set. The SELECT DISKS screen appears. Figure 137. Select Disks Screen 5.
Embedded SATA RAID Figure 138. Create Volume Warning Message 8. Press to create the RAID volume and return to the main menu, or to go back to the CREATE VOLUME menu. 9. From the utility Main Menu, select 5. Exit and then press . The following warning message appears. Figure 139. Intel® Matrix Storage Manager Warning Message 10. Press to exit or press to return to the utility main menu.
Driver Installation 8. Driver Installation 8.1 RAID Driver Installation After creating the RAID sets for your server board, you are now ready to install an operating system to the independent hard disk drive or bootable array. This section provides instructions on how to install the RAID controller drivers during operating system installation. 8.1.1 Creating a RAID Driver Disk TIP The system does not include a floppy drive. You must use a USB floppy drive when creating a SATA RAID driver disk.
Driver Installation 7. Locate the RAID driver and place a blank, high-density floppy disk into the floppy disk drive. 8. Press . 9. Follow screen instructions to create the driver disk. 8.1.1.2 Creating a RAID driver disk from a Microsoft Windows* environment: 1. Start Microsoft Windows*. 2. Place the Resource CD into the optical drive. 3. Go to the Make Disk menu, and then select the type of RAID driver disk you want to create. 4. Insert a floppy disk into the floppy disk drive. 5.
Driver Installation 3. When prompted, press to specify an additional device. Figure 142. Specifying an Additional Device 4. Insert the RAID driver disk you created earlier to the floppy disk drive, then press . 5. Select the RAID controller driver you need from the list, then press . Figure 143. Insert RAID Driver Disk Screen 6. The Microsoft Windows* Setup loads the RAID controller drivers from the RAID driver disk. When prompted, press to continue installation. 7.
Driver Installation 9. Select the option Install the software automatically (Recommended), and then click Next. 10. The wizard searches the RAID controller drivers. When found, click Next to install the drivers. 11. Click Finish after the driver installation is done. 8.1.2.1.2 To verify the RAID controller driver installation: 1. Right-click the My Computer icon on the Windows® desktop, and then select Properties from the menu. 2. Click the Hardware tab, and then click the Device Manager button. 3.
Driver Installation Figure 146. Driver Disk Y/N Screen 4. Select fd0 using the key when asked to select the driver disk source. Press to move the cursor to OK, and then press . Figure 147. Driver Disk Source 5. Insert the Red Hat* Enterprise RAID driver disk to the floppy disk drive, select OK, and then press . Figure 148. Insert Driver Disk Screen 6. When asked if you will load additional RAID controller drivers, select No, and then press . Figure 149.
Driver Installation 8.1.2.3 SUSE Linux Operating System To install the RAID controller driver when installing the SUSE Linux Enterprise Server operating system. 1. Boot the system from the SUSE operating system installation CD. 2. Use the arrow keys to select the Installation from the Boot Options menu. Figure 150. Selecting the SuSe* Installation 3. Press , then select Yes from the menu. Press . Figure 151. Initializing the SuSe* Installation 4.
Driver Installation 5. When the following screen displays, select the floppy disk drive (fd0) as the driver update medium. Select OK and then press . Figure 153. Driver Update Medium Screen The drivers for the RAID controller are installed into the system. 8.2 Intel® Chipset Device Installation This section provides instructions on how to install the Plug and Play components for the Intel® chipset on the system.
Driver Installation Figure 155. Intel® Chipset Device Software Window 5. Select Yes to accept the terms of the License Agreement and continue the process. Figure 156. License Agreement Window 6. Read the Readme File Information and press Next to continue the installation. Figure 157. Readme File Information Window 7. After completing the installation, click Finish to complete the setup process.
Driver Installation Figure 158. Setup Complete Window 8.3 LAN Driver Installation This section provides instructions on how to install the Intel® Gigabit LAN controller drivers on a Microsoft Windows Server* operating system. To install the LAN controller drivers: 1. Restart the computer, and then log on with Administrator privileges. 2. Insert the server board/system Resource CD to the optical drive. The CD automatically displays the Drivers menu if Autorun is enabled in your computer.
Driver Installation Figure 160. Intel Network Connections Software Window 5. Click Next when the Intel(R) Network Connections–InstallShield Wizard window displays. Figure 161. Intel(R) Network Connections—InstallShield Wizard 6. Toggle I accept the terms in the license agreement and click Next to continue. Figure 162. License Agreement Terms 7. Click the Intel(R) PROSet for Windows Device Manager box, and then click Next to start the installation.
Driver Installation Figure 163. Intel(R) PROSet for Windows Device Manager Option 8. Follow the screen instructions to complete installation. Figure 164. Beginning the Installation 9. When finished, click Finish to continue. 8.4 VGA Driver Installation This section provides instructions on how to install the Aspeed® Video Graphics Adapter (VGA) driver. You must manually install the Aspeed* VGA driver on a Windows® Server operating system. To install the Aspeed* VGA driver: 1.
Driver Installation Figure 165. Drivers Menu 3. Click Next to start the installation. Figure 166. Install Wizard for Aspeed* VGA Driver 4. Click Install to update the VGA driver. Figure 167. Updating the VGA Driver 5. When the installation completes, click Finish to restart your computer before using the program.
Driver Installation Figure 168. Completing the VGA Driver Installation 8.5 Management Applications and Utilities Installation The Resource CD that came with the server contains drivers, management applications, and utilities that you can install to support specific server board features. 8.5.1 Running the Resource CD Place the Resource CD into the optical drive. The CD automatically displays the Drivers menu if Autorun is enabled in your computer.
Driver Installation 8.5.3 Utilities Menu The Utilities menu displays the software applications and utilities the server board supports. Click an item to install. Figure 170. Utilities Menu 8.5.4 Make Disk Menu The Make Disk menu provides options to create driver installation floppy disks for supported operating systems. Figure 171. Make Disk Menu 8.5.5 Contact Information For contact information, refer to the “Contact Information” section.
Intel® Server Issue Report Form ® 9. Intel Server Issue Report Form Issue Report Form (Rev 3.6) Note: Filling out this form completely is required for any escalation.
Intel® Server Issue Report Form Has the latest FRU/SDR been tried? (Yes/No): Has the latest HSC been tried? (Yes/No): =============================================================== Processor information Type Speed sSpec Thermal Solution Processor 1 Processor 2 Processor 3 Processor 4 Thermal solution (Heatsink) examples: (1U, Passive w/air ducting, Active w/fan, etc.
Intel® Server Issue Report Form Description/Use Manufacturer Model Firmware Storage Devices (Example: SCSI, SATA, SAS, USB, Tape, etc.
Intel® Server Issue Report Form RAID volumes configuration (disks & RAID level): RAID volume use (Boot device/Data Volume): Is BBU (Battery Backup Unit) installed? (Yes/No): BBU part number: =============================================================== Detailed description of issue: Troubleshooting tried: Steps to replicate the issue: =============================================================== Issue impact statements: Do you have any potential Intel system, or component purchases that this issue
Intel® Server Issue Report Form Do you have systems already purchased that are not being delivered to your customers because of this issue? If yes, please provide a brief description below. Have you returned systems or components to your place of purchase because of this issue? If yes, please provide a brief description below. *All other brands and names are property of their respective owners.
Getting Help 10. Getting Help If you encounter an issue with your server system, follow these steps to obtain support: 1. Visit the following Intel support web page: http://support.intel.com/support/motherboards/server This web page provides 24x7 support when you need it to get the latest and most complete technical support information on all Intel Enterprise Server and Storage Platforms.
Safety Information 11. Safety Information Important Safety Instructions Read all caution and safety statements in this document before performing any of the instructions. See also Intel Server Boards and Server Chassis Safety Information at http://support.intel.com/support/motherboards/server/safecert.htm. Wichtige Sicherheitshinweise Lesen Sie zunächst sämtliche Warn- und Sicherheitshinweise in diesem Dokument, bevor Sie eine der Anweisungen ausführen.
Safety Information English Server Safety Information This document applies to Intel® Server Boards, Intel® Server Chassis (pedestal and rackmount) and installed peripherals. To reduce the risk of bodily injury, electrical shock, fire, and equipment damage, read this document and observe all warnings and precautions in this guide before installing or maintaining your Intel® server product.
Safety Information Intended Application Uses This product was evaluated as Information Technology Equipment (ITE), which may be installed in offices, schools, computer rooms, and similar commercial type locations. The suitability of this product for other product categories and environments (such as medical, industrial, residential, alarm systems, and test equipment), other than an ITE application, may require further evaluation.
Safety Information Do not attempt to modify or use an AC power cord if it is not the exact type required. A separate AC cord is required for each system power supply. The power supply in this product contains no user-serviceable parts. Do not open the power supply. Hazardous voltage, current and energy levels are present inside the power supply. Return to manufacturer for servicing.
Safety Information Disconnect all cables and telecommunication lines that are connected to the system. Retain all screws or other fasteners when removing access cover(s). Upon completion of accessing inside the product, refasten access cover with original screws or fasteners. Do not access the inside of the power supply. There are no serviceable parts in the power supply. Return to manufacturer for servicing.
Safety Information Electrostatic Discharge (ESD) CAUTION ESD can damage disk drives, boards, and other parts. We recommend that you perform all procedures at an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis ground -- any unpainted metal surface -- on your server when handling parts. Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges.
Safety Information Other Hazards Battery Replacement CAUTION There is the danger of explosion if the battery is incorrectly replaced. When replacing the battery, use only the battery recommended by the equipment manufacturer. Dispose of batteries according to local ordinances and regulations. Do not attempt to recharge a battery. Do not attempt to disassemble, puncture, or otherwise damage a battery.
Safety Information Deutsch Sicherheitshinweise für den Server Das vorliegende Dokument bezieht sich auf Intel® Serverplatinen, Intel® Servergehäuse (Standfuß und Rack) sowie installierte Peripheriegeräte. Es enthält Warnungen und Vorsichtsmaßnahmen zur Vermeidung von Gefahren durch Verletzung, Stromschlag, Feuer und Beschädigungen von Geräten. Lesen Sie diese Dokument daher sorgfältig, bevor Sie Ihr Intel® Serverprodukt installieren oder warten.
Safety Information Zielbenutzer der Anwendung Dieses Produkt wurde in seiner Eigenschaft als IT-Gerät getestet, das in Büros, Schulen, Computerräumen und ähnlichen öffentlichen Räumlichkeiten installiert werden kann. Die Eignung dieses Produkts für andere Einsatzbereiche als IT (z. B. Medizin, Industrie, Alarmsysteme oder Prüfgeräte) kann u. U. weitere Tests erfordern. Standortauswahl Das System ist für den Betrieb innerhalb normaler Büroumgebungen geeignet.
Safety Information abgezogen sind. Wenn Sie Komponenten ein- oder ausbauen möchten, die nicht hot-plugfähig sind, stellen Sie sicher, daß zuvor alle Netzkabel abgezogen sind. Nehmen Sie keine Änderungen am Netzkabel vor, und verwenden Sie kein Kabel, das nicht genau dem geforderten Typ entspricht. Jedes Netzteil im System muß über ein eigenes Netzkabel angeschlossen werden. Das Netzteil in diesem Produkt enthält keine Teile, die vom Benutzer gewartet werden können. Öffnen Sie das Netzteil nicht.
Safety Information Schalten Sie das System mit dem Netzschalter aus. Trennen Sie das Gerät von der Stromquelle, indem Sie alle Netzkabel vom System bzw. aus der Steckdose ziehen. Ziehen Sie alle Kabel und alle an das System angeschlossenen Telekommunikationsleitungen ab. Bewahren Sie alle Schrauben und anderen Befestigungselemente gut auf, nachdem Sie die Gehäuseabdeckung entfernt haben.
Safety Information Elektrostatische Entladungen (ESD) VORSICHT Elektrostatische Entladungen können zur Beschädigung von Festplatten, Platinen und anderen Komponenten führen. Daher sollten Sie alle Arbeiten an einer ESD-Workstation ausführen.
Safety Information 2. Prüfen Sie, ob Kabel, Erweiterungskarten sowie weitere Komponenten ordnungsgemäß angebracht sind. 3. Befestigen Sie die Abdeckungen am Gehäuse des Produkts, wie in dessen Anleitung beschrieben. Laser-Peripheriegeräte oder -Komponenten VORSICHT Beachten Sie zur Vermeidung von Strahlung und Verletzungen die folgenden Hinweise: Öffnen Sie keinesfalls das Gehäuse von Laser-Peripheriegeräten oder LaserKomponenten.
Safety Information Français Consignes de sécurité sur le serveur Ce document s’applique aux cartes serveur Intel®, au châssis de serveur Intel® (sur pieds et sur rack) et aux périphériques installés. Pour réduire les risques de dommages corporels, d’électrocution, d’incendie et de dommages matériels, lisez ce document et respectez tous les avertissements et précautions mentionnés dans ce guide avant d’installer ou de mettre à jour votre produit serveur Intel®.
Safety Information Domaines d’utilisation prévus Ce produit a été testé comme équipement informatique (ITE) et peut être installé dans des bureaux, des écoles, des salles informatiques et des endroits commerciaux similaires. L’utilisation du présent produit dans des catégories et environnements de produits et domaines d’application (par exemple, le domaine médical, industriel, résidentiel, les systèmes d’alarme et les appareils de contrôle) autres qu’ITE doit faire l’objet d’évaluations supplémentaires.
Safety Information débrancher le cordon d’alimentation secteur de la prise murale. Votre système peut utiliser plusieurs cordons d’alimentation secteur. Assurez-vous que tous les cordons d’alimentation sont débranchés. Vous devez les débrancher avant d’ouvrir le châssis, d’ajouter ou de supprimer un composant non connectable à chaud. N’essayez pas de modifier ou d’utiliser un cordon d’alimentation secteur s’il ne s’agit pas du type exact requis.
Safety Information Avertissements sur l’accès au système ATTENTION Pour éviter de vous blesser ou d’endommager votre équipement, les consignes de sécurité suivantes s’appliquent chaque fois que vous accédez à l’intérieur du produit : Mettez hors tension tous les périphériques connectés à ce produit. Éteignez le système en appuyant sur le bouton d’alimentation. Déconnectez l’alimentation secteur en débranchant tous les cordons d’alimentation secteur du système ou de la prise murale.
Safety Information Vous êtes responsable de l’installation d’un disjoncteur principal d’alimentation pour la totalité du rack. Ce disjoncteur principal doit être rapidement accessible et doit être étiqueté comme contrôlant toute l’unité, et pas uniquement le ou les serveurs. Pour éviter tout risque d’électrocution, le rack et chaque élément de l’équipement installé dans le rack doivent être correctement reliés à la terre.
Safety Information Afin de permettre une ventilation et un refroidissement corrects, ne mettez le système en marche que lorsque les panneaux du châssis sont en place. L’utilisation du système sans les panneaux peut endommager les composants système. Pour installer les panneaux : 1. Vérifiez tout d’abord que vous n’avez pas oublié d’outils ou de composants détachés à l’intérieur du système. 2. Vérifiez que les câbles, les cartes d’extension et les autres composants sont correctement installés. 3.
Safety Information Español Información de seguridad del servidor Este documento se aplica a las tarjetas de servidor de Intel®, las carcasas de servidor de Intel® (montaje en bastidor y en pedestal) y los dispositivos periféricos. Para reducir el riesgo de daños corporales, descargas eléctricas, fuego y en el equipo, lea este documento y preste atención a todos las advertencias y precauciones de esta guía antes de instalar o mantener el producto de servidor de Intel®.
Safety Information Aplicaciones y usos previstos Este producto ha sido evaluado como equipo de tecnología informática (ITE) que puede instalarse en oficinas, escuelas, salas de equipos informáticos o lugares de ámbito comercial similares.
Safety Information alimentación de CA estén desenchufado antes de abrir la carcasa, agregar o extraer cualquier componente que no es de conexión en funcionamiento. No intente modificar ni utilizar un cable de alimentación de CA si no es del tipo exacto requerido. Se necesita un cable de CA para cada fuente de alimentación del sistema. La fuente de alimentación de este producto no contiene piezas que puedan ser reparadas por el usuario. No abra la fuente de alimentación.
Safety Information Desconecte la alimentación de CA desenchufando los cables de alimentación de CA del sistema o de la toma de corriente alterna. Desconecte todos los cables y líneas de telecomunicación que estén conectados al sistema. Guarde todos los tornillos o elementos de fijación cuando retire las cubiertas de acceso. Cuando termine de operar en el interior del producto, vuelva a colocar los tornillos o los elementos de fijación originales de la cubierta de acceso.
Safety Information Descarga electrostática (ESD) PRECAUCIÓN Las descargas electrostáticas pueden dañar las unidades de disco, las tarjetas y otros componentes. Recomendamos que realice todos los procedimientos en una estación de trabajo protegida contra descargas electrostáticas.
Safety Information Periféricos o dispositivos láser PRECAUCIÓN Para evitar el riesgo de la exposición a radiaciones o de daños personales: No abra la caja de ningún periférico o dispositivo láser Los periféricos o dispositivos láser no pueden ser reparados por el usuario Haga que el fabricante los repare Intel® Server System SR1670HV Service Guide 137
Safety Information 简 体中文 服务 器安全信息 本文档适用于 Intel® 服务器主板、Intel® 服务器机箱（基座和机架固定件）和已安装的外 设。为减少人身伤害、电击、火灾以及设备毁坏的危险，请在安装或维护 Intel® 服务器产 品之前阅读本文档并遵循本指南中的所有警告和预防措施。 如果本文档中的信息与特定产品的随附信息或 Web 站点信息之间存在不一致，请以产品文 档为准。 服务器须由合格的技术人员进行集成和维护。 必须遵守本指南的规定和服务器手册的装配指导，以确保符合现有的产品认证和审批。仅使 用本指南中描述和规定的指定组件。使用其他产品/组件将使产品的 UL 认证和其他管理审 批无效，并可能导致产品不符合销售地的产品法规。 安全警告与注意事项 为避免人身伤害与财产损失，安装本产品之前，请阅读以下所有安全指导和信息。下面所列 的安全符号可能在整个文档中使用并可能标注于产品和/或产品包装之上。 注意 表示如果无视此“注意事项”，存在可能引起轻微人身伤害或财产损失的危险。 警告 表示如果无视此“警告”，存在可能引起严重人身伤害的危险。 表示如果无视所示信息，即存在潜在的危
Safety Information 场 地选 择 本系统专为在典型办公环境运行而设计。请选择符合以下条件的地点： 清洁、干燥，无气载微粒（而非一般的室内尘埃）。 通风良好，远离热源（包括直接日晒和散热器）。 远离振动源或物理震动。 与电气设备产生的强大电磁场隔离。 在易受闪电袭击的地区，我们建议将系统插入电涌抑制器并在闪电期间断开通信线路与 调制解调器之间的连接。 提供正确接地的墙壁插座。 提供足够的空间，以便拿取电源供应线，因为这是本产品的主要电源断开器。 设 备 操作规 范 减少人身伤害或设备受损的危险： 移举设备时遵守当地的职业健康与安全要求。 借助机械手段或其他合适的手段移举设备。 拆除一切易分离组件，以降低重量并方便操作。 电 源与电 气警告 注意事项 电源按钮（如待机电源标记所示）并不能完全关闭系统的交流电源，只要系统已接通电源， 就存在 5V 待机电源。要从系统切断电源，须从墙壁电源插座中拔下交流电线。您的系统可 能不止使用一根交流电线。请确保所有的交流电线都已拔下。打开机箱或增加或去除任何热 插拔组件之前，确保交流电线已拔下。 若非所需的确切类型
Safety Information 电 源线 警告 如果产品未提供交流电线，请购买一根您所在国家批准使用的交流电线。 注意事项 为避免电击或火灾危险，请按如下所述对产品所用的电源线进行检查： 若非所需的符合接地插座的确切类型，请勿尝试修改或使用交流电线 电源线须符合以下标准： 电源线的电气额定值须大于产品上标注的电流额定值。 电源线须拥有适合插座的安全接地插头或触点。 电源线为交流电源的主要断开设备。插座须靠近设备并可随时断开。 电源线须插入所提供的拥有合适接地的插座。 系统 使用警告 注意事项 为避免人身伤害或财产损失，无论何时检查产品内部，以下安全指导都适用： 关闭所有与本产品相连的外设。 按下电源按钮至关闭状态，关闭系统。 从系统或墙壁插座上拔下所有交流电线，断开交流电源。 断开与系统相连的所有线缆和通信线路。 卸除舱口盖时，保留所有螺钉及其他紧固件。完成产品内部检查之后，请用螺钉或 紧固件重新固定舱口盖。 请勿打开电源供应设备。电源供应设备内没有可维修部件。请与生产商联系维修事 宜.
Safety Information 机架固定件警告 设备的机架须固定在稳固的支座上，以防从中安装服务器或设备时倒塌。须按照机架生产商 提供的安装说明进行安装。 从下往上将设备安装在机架上，最重的设备安装在机架的最底层。 一次只从机架上安装一件设备。 您须负责安装整个机架装置的主要电源断开设备。此主要断开设备须随时可用，且须标明为 控制整个装置（而不仅限于服务器）的电源。 为避免潜在的电击危险，须对机架及其上所安装的每一件设备实行正确的安全接地。 静电 放电 (ESD) 注意事项 ESD 会损坏磁盘驱动器、主板及其他部件。我们建议您执行 ESD 工作站的所有步骤。如果 没有 ESD 工作站，则采取一些静电放电保护措施，操作部件时，戴上与服务器上的机箱接 地或任何未喷漆金属表面连接的防静电腕带。 操作主板时始终保持小心。它们可能对 ESD 非常敏感。拿持主板时只接触边缘。从保护包 装中或从服务器上取出主板后，请将主板组件侧面朝上放置在无静电的接地表面上。请使用 导电泡沫垫（若有），不要使用主板包装。请勿将主板在任何表面上滑动。 其他危险 替换 电 池 注意事项 不正确替换电池可能导致爆炸危险。替换电池时，
Safety Information 冷却和气流 注意事项 按照说明小心布置线缆，尽量减少气流阻塞和冷却问题。 为保证适当的冷却和气流，运行系统时请确保机箱盖已安装。未安装机箱盖即运行系统可能 导致系统部件受损。安装机箱盖的步骤如下： 首先检查并确保系统内没有遗留的未固定工具或部件。 1. 检查线缆、内插板和其他组件已正确安装。 2.
