Quick Start Guide Back Page

ManualsBrandsIntel ManualsOtherIntel Server Board S5500BC

Side 2

Install Rack

Mount Kit

(Optional)

If you intend to configure your server as

a pedestal system, disregard this step

and proceed to Step 17.

If you intend to configure your server as

a rack-mount system, go to the

instructions that came with your Rack

Mount Kit to complete your server

assembly.

Install Feet

Note: Repeat above steps until all four feet are installed.

Secure foot by inserting pin through the rubber foot.

Insert rubber foot into chassis hole.

Note: This step applies to the pedestal version only. If you plan

to configure your chassis as a rack mount system, go to Step 16.

Install Hot-Swap

Drive Cage Kit

(Optional)

If you intend to configure your

server with SATA/SAS hot swap

hard drives, go to the instructions

that came with your drive cage

upgrade kit to install the

drive cage and hot-swap drives.

Install Tool-less Fixed Hard Drives

(If installing a hot-swap drive cage,

go to Step 10)

Install power and data cables to each

of the installed drives. The cables

route through the oval opening at

the bottom of the drive cage.

Re-attach drive cage EMI shield

to chassis.

Tighten thumb screw.

Accessories and Order Codes

6-Drive SAS/SATA Hot Swap Cage

without expander

6-Drive SAS/SATA Hot Swap Cage

with expander

Intel

Server Chassis Rack Mount Kit

Intel

Server System SC5650BCDP

Product Maintenance Kit

AXX6DRV3GR

AXX6DRV3GEXP

APP3RACKIT

APPTPMKIT

Hot Swap Conversion Kit

APPTHSDBKIT

Requires a Hot Swap Conversion Kit to integrate into the Intel

Server

System SC5650BCDP.

A complete list of accessories and spares can be found at:

http://support.intel.com

Document Type

Available Documents

Technical Product Specification

Spares and Configuration Guide

Software and Drivers

Content

In-depth technical information

Supported accessories and spares list

Up-to-date firmware, driver and

utility information

Additional Reference Documents available at: http://support.intel.com

Close System

Replace screws.

Slide the

side cover on

chassis and

latch securely.

CAUTION: This

chassis must be

operated with the

SIDE COVER

installed to ensure

proper cooling.

Remove Filler

Panels

Remove the bezel filler panels for each

drive you have installed. Release plastic

tabs located at back side of bezel and

pull out filler panels from front.

Install Tool-less CD-ROM or DVD-ROM Drive

Remove EMI shield from 5.25-inch device drive bay.

Make sure latch is in "unlock" position.

Line up holes in CD-ROM or DVD-ROM drive with

holes in chassis.

Connect power (P5 or P6) cables and data cables

to rear of the CD-ROM or DVD-ROM

Move latch to "lock" position.

Insert CD-ROM or DVD-ROM drive into device drive bay.

An additional 4-pin IDE male-to-SATA 15 pin power cable

adapter may be needed if the CD-ROM or DVD-ROM does

not have a 4-pin power connector.

Data cables are included with the Intel

Server Board.

Data

Power

Install Front Bezel Assembly

Engage three clips

at right edge of

chassis.

Rotate left side

of bezel assembly

toward chassis.

Snap two bezel tabs

into corresponding

recesses at left edge

of chassis front panel.

Chassis Features and Components

A. Front Panel

B. 5.25-inch Device

Drive Bays (2)

C. Hard Drive Cage

Access Door

D. Door Lock

E. USB Ports (2)

F. Fan Duct and

System Fan

(DP/WS/BRP

configuration

shown)

G. Hard Drive Cage

Retention

Mechanism

H. Alternate external

SCSI Knockout

I. Fixed Hard

Drive Fan

SC5650BCDP Mother Board

K. Padlock Loop

L. PCI Card Guide

M. External SCSI

Knockout

N. Serial B port

Knockout

O. Power Supply

(fixed illustrated)

P. A/C Power In

Q. I/O Shield

R. PCI Add-in

Board Slots

Install PCI Card Guide

Insert tabs on left side of PCI card guide into slots in chassis.

Swing PCI card guide into chassis until right-side blue tabs snap into place.

Install Tool-less Fixed Hard Drives (If installing a hot-swap drive cage, go to Step 10) (Continued...)

Insert fixed drive cage into chassis.

Route power and data cables

through cable routing area at the

bottom of the fixed drive cage.

Pull the drive latch forward for the drive

bay you want to install a hard drive in.

Drive slots 1, 3, and 5 MUST be

populated first. Failure to do so

could result in thermal issues

within chassis.

Insert fixed hard drive into drive bay

until it stops. Ensure that the power

and data connector end of the hard drive

is facing forward.

Push drive latch in to lock hard drive

into drive bay.

Install additional drives as necessary.

Server Board S5500BC

Component Layout

See your Intel

Server

System S5500BCDP User's

Guide for expanded

component and

connection information.

ICH10

Note: Refer to the

Technical Product

Specification for

Diagnostic LED

decoder list.

Diagnostic LEDs

DIMM_A2

DIMM_A1

DIMM_B2

DIMM_B1

DIMM_E1

DIMM_E2

DIMM_D1

DIMM_D2

CPU 1 Socket

CPU 2 Socket

Slot 7 (PCI Express* x8)

Slot 6 (PCI Express* x8, Riser Card)

Slot 5 (PCI Express* x4)

Slot 4 (PCI 32/33)

RMM3

Slot 3 (PCI Express* x4)

NIC 2

USB 9

USB 8

NIC 1

USB 7

USB 6

VGA

Serial A

SYS FAN 3

SYS FAN 2

SATA 4

USB 2-3

USB 0-1

SATA 5

Serial B

HSBP_A

Main Power

CPU Power

BIT1

LSB

DIMM Fault

LEDs

Front Panel Header

CPU 1 FAN

SYS FAN 1 CPU 2 FAN

DIMM Fault LEDs

IOH

P/S AUX

SATA RAID

Key

Status LED

ID LED

BIT3

BIT2

BIT6

MSB

BIT4

BIT5

BMC

SATA 0

SATA 1

SATA 3

SATA 2

Battery

IPMB_1

SATA SGPIO

Install PCI Add-in Boards

While holding the PCI add-in

board by its top edge or upper

corners, firmly press the add-in

board into the expansion slot.

Close the back panel PCI add-in

board retention device.

From inside of chassis, press open

the back panel PCI add-in board

retention device.

Remove the PCI slot shield by

pressing the shield out from

the inside of the chassis.

Front Panel Controls

and Indicators

A. Power/Sleep

LED

B. Power/Sleep

Button

C. NMI Button

D. Reset Button

E. NIC 1 Activity

LED

F. NIC 2 Activity

LED

G. Hard Drive

Activity LED

H. Status LED

Reference

Finishing Up

1. See your Intel

Server Board

Quick Start User's Guide to

connect your keyboard,

mouse, video and other I/O

cables.

2. Connect the AC power

cable last.

CAUTION: Power supply

requires a 16-gauge

power cord.

Install Software

BIOS, Drivers, and Operating

System Install

A. Conﬁrm BIOS Version:

Look on the

Server/System Management screen in the BIOS

Setup Utility to determine the installed BIOS

version.

Compare this to the versions at:

http://support.intel.com/support/motherboards/server/S5500BC/

If new versions are available, update the BIOS

on your server. See the User Guide on the

Intel

Server Deployment Toolkit CD for

update instructions.

B. Conﬁgure your RAID Controller:

Use the instructions provided with the

RAID controller.

C. Install your Operating System:

Use the instructions provided with the RAID

controller and with the operating system.

D. Install Operating System Drivers:

With the operating system running, insert the

Intel

Server Deployment Toolkit CD. If using

a Microsoft* Windows*operating system,

the Express Installer will autorun and allow

you to select the appropriate drivers to install.

On other operating systems, browse the CD

folders to locate and install the driver files.

Complete Server

Board Connections

See your Intel

Server Board Quick Start

User's Guide or the User Guide for server

board cable connections.

Fan Connection

Fan Header Used Notes

System Fan 1 PCI Zone Chassis Fan

System Fan 2 HDD Cage Fan

System Fan 3 Rear Chassis Fan