Technical Product Specification

ManualsBrandsIntel ManualsOtherIntel Server Board S2600WP

Intel

Server Chassis H2000 Family

Intel order number: G59059-001

Revision 1.0

February, 2012

Enterprise Platforms and Services Division

Summary of content (58 pages)

PAGE 1
Intel® Server Chassis H2000 Family Technical Product Specification Intel order number: G59059-001 Revision 1.
PAGE 2
® Revision History Intel Server Chassis H2000 Family TPS Revision History Date Revision Number February, 2012 1.0 Modifications Initial release. ii Revision 1.
PAGE 3
® Intel Server Chassis H2000 Family TPS Disclaimers Disclaimers Information in this document is provided in connection with Intel® products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document.
PAGE 4
Table of Contents ® Intel Server Chassis H2000 Family TPS Table of Contents 1. Introduction ........................................................................................................................ 1 1.1 Chapter Outline ...................................................................................................... 1 1.2 Server Board Use Disclaimer ................................................................................. 2 2. Product Overview .................................
PAGE 5
® Intel Server Chassis H2000 Family TPS Table of Contents 3.2.17 AC Line Isolation .................................................................................................. 17 3.2.18 AC Power Inlet ..................................................................................................... 17 3.3 DC Ouput Specification ........................................................................................ 18 3.3.1 Output Power/Currents...................................................
PAGE 6
Table of Contents ® Intel Server Chassis H2000 Family TPS 5.3.3 3.5" Hot Swap Backplane Connector scheme ...................................................... 32 5.3.4 2.5" Hot Swap Backplane Connector scheme ...................................................... 33 5.3.5 Backplane LED Support ....................................................................................... 34 5.3.6 Backplane Connector Definition ........................................................................... 35 6.
PAGE 7
® Intel Server Chassis H2000 Family TPS List of Figures List of Figures Figure 1. Chassis Overview (H2312xx SKU) ............................................................................... 4 Figure 2. Power Supply Scheme (Rear View) ............................................................................. 4 Figure 3. Dummy Tray Cover ...................................................................................................... 4 Figure 4. Major Chassis Parts ..............................
PAGE 8
List of Tables ® Intel Server Chassis H2000 Family TPS List of Tables Table 1. Chassis Feature Set ...................................................................................................... 3 Table 2. Chassis SKU Matrix ...................................................................................................... 3 Table 3. Chassis Dimension (SKU: H2312xxJR/KR) ................................................................... 5 Table 4. Chassis Dimension (SKU: H2216xxJR/KR) ........
PAGE 9
® Intel Server Chassis H2000 Family TPS List of Tables Table 40. Power Supply Control Connector Pin-out .................................................................. 38 Table 41. Front Control Button Function.................................................................................... 40 Table 42. Front LED Indicator Functions ................................................................................... 40 Table 43. Power LED Operation ...................................................
PAGE 10
List of Tables ® Intel Server Chassis H2000 Family TPS x Revision 1.
PAGE 11
® Intel Server Chassis H2000 Family TPS 1. Introduction Introduction This Technical Product Specification (TPS) provides system specific information detailing the features, functionality, and high-level architecture of the Intel® Server Chassis H2000 family. You should also reference the Intel® Server System H2000JF, H2000WP, H2000LP Family Technical Product Specification to obtain greater detail of functionality and architecture of the server board integrated in this server system.
PAGE 12
® Introduction 1.2 Intel Server Chassis H2000 Family TPS Server Board Use Disclaimer Intel Corporation server boards support add-in peripherals and contain a number of high-density VLSI and power delivery components that need adequate airflow to cool. Intel® ensures through its own chassis development and testing that when Intel® server building blocks are used together, the fully integrated system will meet the intended thermal requirements of these components.
PAGE 13
® Intel Server Chassis H2000 Family TPS 2. Product Overview Product Overview The Intel® Server Chassis H2000 family includes two major SKUs: H2312xxJR/KR and H2216xxJR/KR, which are supporting rack mount 2U 4-node server systems, purpose-built for high-density and lowest total cost of ownership in dense computing applications, such as HPC and IPDC.
PAGE 14
Product Overview 2.1 Intel® Server Chassis H2000 Family TPS Chassis Views Figure 1. Chassis Overview (H2312xx SKU) Figure 2. Power Supply Scheme (Rear View) Figure 3. Dummy Tray Cover Revision 1.
PAGE 15
® Intel Server Chassis H2000 Family TPS 2.2 Product Overview Chassis Dimensions Table 3. Chassis Dimension (SKU: H2312xxJR/KR) Height 87.9 mm 3.46" Width 438 mm 17.24" Depth 771 mm 30.35" Table 4. Chassis Dimension (SKU: H2216xxJR/KR) 2.3 Height 87.9 mm 3.46" Width 438 mm 17.24" Depth 733 mm 28.86" System Level Environmental Limits The following table defines the system level operating and non-operating environmental limits. Table 5.
PAGE 16
Intel® Server Chassis H2000 Family TPS Product Overview Parameter Limits Line to earth Only AC Leads I/O Leads DC Leads Air Discharged 12.0 kV Contact Discharge 8.0 kV Operating -16 to 3048 m (-50 to 10,000 ft.) Note: For altitudes above 2950 feet, the maximum operating temperature is de-rated 1°F/550 ft. Storage -16 to 10,600 m (-50 to 35,000 ft.) 2.0 kV 1.0 kV 0.5 kV ESD Altitude 2.
PAGE 17
Intel® Server Chassis H2000 Family TPS Product Overview Hard Drive and Peripheral Bays 2.5 Intel® Server System H2312xx Not Supported Intel® Server System H2216xx Not Supported Not Supported Not Supported SATA/SAS Hard Disk Drives (3.5-inch) Up to Twelve Not Supported SATA/SAS Hard Disk Drives (2.5-inch) Not Supported Up to Sixteen Slim-line SATA Optical Drive Internal USB Floppy Drive Figure 5. Intel® Server Chassis H2312xx Drive Bay Front View Figure 6.
PAGE 18
Product Overview  ® Intel Server Chassis H2000 Family TPS A basic slide rail kit (Product order code – AXXELVRAIL) is designed to mount the chassis into a standard (19 inches by up to 30 inches deep) EIA-310D compatible server cabinet. 8 Revision 1.
PAGE 19
® Intel Server Chassis H2000 Family TPS 3. Power Sub-System Power Sub-System The system supports AC 1+1 hot swap power supply module and two power distribution board which can support 2U rack high density server system. Two different power supply units are supported: 1200W and 1600W. The single power supply module has Platinum level energy efficiency, demonstrating climate saver with silver rating. 3.
PAGE 20
® Power Sub-System Intel Server Chassis H2000 Family TPS Table 6. Specification Data for AC Power Supply Unit Wattage Voltage Heat Dissipation Maximum Inrush Current 1200W/1600W (Energy Smart) 90 – 264 VAC, auto-ranging, 47 Hz-63 Hz 2560 BTU/hr Under typical line conditions and over the entire system ambient operating range, the inrush current may reach 65 A per power supply for 5 ms Platinum Platinum 80 Plus rating Climate Saver (CS) rating 3.1.
PAGE 21
® Intel Server Chassis H2000 Family TPS A18 A19 A20 A21 A22 A23 A24 A25 Power Sub-System PSU Output Connector +12V B18 +12V PMBus SDA* B19 A0* (SMBus address) PMBus SCL* B20 A1* (SMBus address) PSON B21 12V STBY SMBAlert# B22 Cold Redundancy Bus* Return Sense B23 12V load share bus +12V Remote Sense B24 No Connect PWOK B25 CRPS Compatibility Check pin* *: Refer to the spec of CRPS Common Requirements specification. 3.1.6 Handle Retention The power supply has a handle to assist extraction.
PAGE 22
® Power Sub-System Intel Server Chassis H2000 Family TPS A B C Power Distribution Board 1 Power Distribution Board 2 Power Supply Unit #2(upper) and #1(lower) Figure 9. Power Cage Overview 3.1.9 Power Cage Output Pin Assignment The power cage provides +12V and +12VSTB output to the system. Each PDB has two 2x9 power output cable to system backplane, together with one 2x8 signal control cable for power management. Refer to below table for PDB pin assignment. 12 Revision 1.
PAGE 23
® Intel Server Chassis H2000 Family TPS A B C D Power Sub-System Main Power Output Connector P1 Power Supply Unit Connector Control Signal Connector Main Power Output Connector P2 Figure 10. Power distribution board Table 10. Pin assignment of power ouput connector Pin Description Pin Description 1 GND 2 +12V 3 GND 4 +12V 5 GND 6 +12V 7 GND 8 +12V 9 GND 10 +12V 11 GND 12 +12V 13 GND 14 +12V 15 GND 16 +12V 17 GND 18 +12V Table 11.
PAGE 24
® Power Sub-System Intel Server Chassis H2000 Family TPS Pin 3.2 3.2.1 Description Pin Description 9 Return Sense 10 PWOK 11 +12V Remote Sense 12 Compatibility Bus 13 Reserved 14 +12VSB 15 +12VSB 16 Key Pin (removed) AC Input Specification Input Voltage And Frequency The power supply must operate within all specified limits over the following input voltage range. Harmonic distortion of up to 10% THD must not cause the power supply to go out of specific limits.
PAGE 25
® Intel Server Chassis H2000 Family TPS Power Sub-System Table 14. Platinum Efficiency Requirement Loading Minimum Efficiency 100% of maximum 50% of maximum 20% of maximum 10% of maximum 91% 94% 90% 82% The power supply must pass with enough margins to make sure in production all power supplies meet these efficiency requirements. 3.2.4 AC Line Fuse The power supply shall have one line fused in the single line fuse on the line (Hot) wire of the AC input.
PAGE 26
® Power Sub-System Intel Server Chassis H2000 Family TPS  These input transients must not cause any out-of-regulation conditions, such as overshoot and undershoot, nor must it cause any nuisance trips of any of the power supply protection circuits.  The surge-withstand test must not produce damage to the power supply. The supply must meet surge-withstand test conditions under maximum and minimum DC-output load conditions. 3.2.
PAGE 27
® Intel Server Chassis H2000 Family TPS 3.2.14 Power Sub-System AC Line Transient Specification AC line transient conditions shall be defined as “sag” and “surge” conditions. “Sag” conditions are also commonly referred to as “brownout”, these conditions will be defined as the AC line voltage dropping below nominal voltage conditions. “Surge” will be defined to refer to conditions when the AC line voltage rises above nominal voltage.
PAGE 28
® Power Sub-System Intel Server Chassis H2000 Family TPS The AC power cord must meet the following specification requirements: Cable Type Wire Size SJT 16 AWG Temperature Rating 105º C Amperage Rating 13 A Voltage Rating 125 V Figure 11. AC Power Cord Specification DC Ouput Specification 3.3 3.3.1 Output Power/Currents The following table defines the minimum power and current ratings. The power supply must meet both static and dynamic voltage regulation requirements for all conditions.
PAGE 29
® Intel Server Chassis H2000 Family TPS Power Sub-System Table 20. Voltage Regulation Limits Parameter Min Nom Max Unit Tolerance +12VSTB +11.40V +12.000V +12.60V Vrms ±5% +12V +11.40V +12.000V +12.60V Vrms ±5% The combined output continuous power of all outputs shall not exceed 3200W (1600W from each power supply unit). Each output has a maximum and minimum current rating shown in below table.
PAGE 30
® Power Sub-System Intel Server Chassis H2000 Family TPS +12V 120mVp-p 3.3.7 +12VSTB 120mVp-p Grounding The output ground of the pins of the power supply provides the output power return path. The output connector ground pins shall be connected to the safety ground (power supply enclosure). This grounding should be well designed to ensure passing the max allowed Common Mode Noise levels. The power supply shall be provided with a reliable protective earth ground.
PAGE 31
® Intel Server Chassis H2000 Family TPS 3.3.12 Power Sub-System Zero Load Stability Requirement When the power subsystem operates in a no load condition, it does not need to meet the output regulation specification, but it must operate without any tripping of over-voltage or other fault circuitry. When the power subsystem is subsequently loaded, it must begin to regulate and source current without fault. 3.3.
PAGE 32
® Power Sub-System Intel Server Chassis H2000 Family TPS Item Description asserted at turn on. T pwok_off Delay from PWOK de-asserted to output voltages dropping out of regulation limits. T pwok_low Duration of PWOK being in the de-asserted state during an off/on cycle using AC or the PSON signal. T sb_vout Delay from 12VSBbeing in regulation to O/Ps being in regulation at AC turn on. T Time the 12VSBoutput voltage stays within regulation after loss of AC.
PAGE 33
® Intel Server Chassis H2000 Family TPS Power Sub-System below the Vfault threshold. Asserting the CR_BUS signal causes all power supplies in Cold Standby state to power ON. Enabling power supplies to maintain best efficiency is achieved by looking at the Load Share bus voltage and comparing it to a programmed voltage level through a PMBus command.
PAGE 34
® Power Sub-System Intel Server Chassis H2000 Family TPS Table 27. PSON# Signal Characteristics. Signal Type # PSON = Low # PSON = High or Open Logic level low (power supply ON) Logic level high (power supply OFF) Source current, Vpson = low Power up delay: Tpson_on_delay PWOK delay: T pson_pwok 3.5.2 Accepts an open collector/drain input from the system. Pull-up to VSB located in power supply. ON OFF MIN MAX 0V 1.0V 2.0V 3.
PAGE 35
® Intel Server Chassis H2000 Family TPS Power Sub-System Table 29. SMBAlert# Signal Characteristics Open collector/drain output from power supply. Pullup to VSB located in system. OK Signal Type (Active Low) Alert# = High Alert# = Low MIN 0V Logic level low voltage, Isink=4 mA Logic level high voltage, Isink=50 A Sink current, Alert# = low Sink current, Alert# = high Alert# rise and fall time 3.6 Power Alert to system MAX 0.4 V 3.
PAGE 36
® Power Sub-System 3.6.3 Intel Server Chassis H2000 Family TPS Over Thermal protection The power supply will be protected against over temperature conditions caused by loss of fan cooling or excessive ambient temperature. In an OTP condition the PSU will shut down. When the power supply temperature drops to within specified limits, the power supply shall restore power automatically, while the 12VSB remains always on.
PAGE 37
® Intel Server Chassis H2000 Family TPS Power Sub-System Table 32. PSU addressing 3.7.2 PDB addressing Address0 0 1 Power supply PMBus* device B0h B2h Accuracy The sensor commands shall meet the following accuracy requirements. The accuracies shall be met over the specified ambient temperature and the full range of rated input voltage. Table 33.
PAGE 38
® Cooling Sub-System 4. Intel Server Chassis H2000 Family TPS Cooling Sub-System The chassis cooling system contains the fan cooling sub-system of each node tray and common fan cooling in the power supply units. Both node fans and PSU fans work together as thermal solution to the chassis. For each node, several components and configuration requirements make up the cooling subsystem. These include processors, chipsets, VR heatsinks, system fan module, CPU air duct, and drive bay population.
PAGE 39
® Intel Server Chassis H2000 Family TPS 5. Hard Disk Drive Support Hard Disk Drive Support The server system provides two SKUs to support different types of Hard Disk Drives (HDD): 5.1  H2312xx : Supports 12x 3.5" HDD  H2216xx : Supports 16x 2.5" HDD Hard Disk Drive Bays Scheme The server system H2000 chassis can support up to twelve carrier-mounted SATA/SAS 3.5-inch hard disk drives, or sixteen carrier-mounted SATA/SAS 2.5" hard disk drives.
PAGE 40
Intel® Server Chassis H2000 Family TPS Hard Disk Drive Support Figure 17. 3.5" HDD Assembly Overview Figure 18. 2.5" HDD Assembly Overview Hot-swap drive carriers make insertion and extraction of the drive from the system very simple. Each type of drive carrier has its own latching mechanism, which is used to both insert and extract drives from the chassis and lock the carrier in place.
PAGE 41
® Intel Server Chassis H2000 Family TPS     Hard Disk Drive Support H2312xxJR/KR: 12x SAS/SATA 3.5" HDDs at 6Gb/s SAS/SATA or slower speeds, divided into 4 groups of three hot swap hard drives. Each HDD group is associated with one of the four compute nodes respectively in the 2U chassis. H2216xx/JR/KR: 16x SAS/SATA 2.5" HDDs at 6Gb/s SAS/SATA or slower speeds, divided into 4 groups of four hot swap hard drives.
PAGE 42
Intel® Server Chassis H2000 Family TPS Hard Disk Drive Support 5.3.2 Backplane Block Diagram Figure 19. Passive Backplane Block Diagram (for one node) 5.3.3 3.5" Hot Swap Backplane Connector scheme The following diagrams show the layout of major components and connectors for 3.5" Hot Swap backplane. A SATA/SAS connectors for Node 1 B SATA/SAS connectors for Node 2 C SATA/SAS connectors for Node 3 D SATA/SAS connectors for Node 4 Figure 20. 3.
PAGE 43
Intel® Server Chassis H2000 Family TPS A 20-pin Front Panel cable connector for Node 2, 4 B 2Blade Compute Node Power connector for Node 4 C 2x40 pin Bridge Board connector for Node 4 D 2x9 pin Power supply input connector E 2x9 pin Power supply input connector F 2x7 pin Power Control cable connector G 2Blade Compute Node Power connector for Node 3 H 2x40 pin Bridge Board connector for Node 3 I 2x40 pin Bridge Board connector for Node 1 J 20-pin Front Panel cable connector for Node 1, 3
PAGE 44
Intel® Server Chassis H2000 Family TPS Hard Disk Drive Support A SATA/SAS connectors for Node 1 B SATA/SAS connectors for Node 2 C SATA/SAS connectors for Node 3 D SATA/SAS connectors for Node 4 Figure 22. 2.
PAGE 45
® Intel Server Chassis H2000 Family TPS Hard Disk Drive Support Figure 24. Hard Drive Carrier LED General HDD LED functionality is displayed below: Table 34. Hard Drive Carrier Status LED Functions Amber Off Solid On Blink No access and no fault Hard Drive Fault has occurred Raid rebuild in progress (1hz) Identify (2hz) Table 35. Hard Drive Carrier Activity LED Functions Condition Power on with no drive activity. Power on with drive activity. Green Power on and drive spun down.
PAGE 46
® Hard Disk Drive Support Pin 14 16 18 Intel Server Chassis H2000 Family TPS Signal Description P12V P12V P12V Pin 13 15 17 Signal Description GND GND GND 2. 2Blade Compute Node Power Connector The backplane provides main power to compute node through 2-Blade power connector. Table 37.
PAGE 47
® Intel Server Chassis H2000 Family TPS Pin 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 Hard Disk Drive Support Signal Description SMBUS_R7 CLK GND PMBUS Alert_N NODEx_ON_N SGPIO DATA IN SGPIO Data Out SGPIO LD SPKR GND SAS3_RX SAS3_RX GND SAS2_TX SAS2_TX GND SAS1_RX SAS1_RX GND SAS0_TX SAS0_TX GND 3.
PAGE 48
® Hard Disk Drive Support Intel Server Chassis H2000 Family TPS Pin 17 18 19 20 Signal Description FP2_HEALTH_LEDG_N FP2_HEALTH_LEDA_N FP2_ACTIVITY_LED_N FP2_ID_LED_N 5. 2x7 Pin Power Supply Control Signal Connector The backplanes provide power supply control signals, together with PMBus functionality integrated. Table 40.
PAGE 49
Front Panel Control and Indicators 6. Intel® Server Chassis H2000 Family TPS Front Panel Control and Indicators The Intel® Server Chassis H2000 family Front Control Panel is integrated with rack handles at the both sides of the chassis. Each control panel contains two sets of node control buttons and status LEDs. The control panel assembly is pre-assembled and fixed with the rack handles. A B C D System Power Button with LED System ID LED Button System Status LED Network Link/Activity LED Figure 25.
PAGE 50
® Intel Server Chassis H2000 Family TPS Front Panel Control and Indicators Control Panel Button 6.1 The following table lists the control panel features and functions. The control panels features a system power button. Table 41. Front Control Button Function Feature Power Button with Power LED System ID Button with ID LED Function Toggles the system power on/off. This button also integrates the power LED. Toggles between ID LED on and off Control Panel LED Indicators 6.
PAGE 51
® Front Panel Control and Indicators 6.2.1 Intel Server Chassis H2000 Family TPS Power/Sleep LED Table 43. Power LED Operation State Power Off Power On Power Mode Non-ACPI Non-ACPI LED Off Solid On S5 ACPI Off S1 Sleep ACPI Blink S0 ACPI Solid On Description System power is off and the BIOS has not initialized the chipset. System power is on but the BIOS has not yet initialized the chipset. Mechanical is off and the operating system has not saved any context to the hard disk.
PAGE 52
® Intel Server Chassis H2000 Family TPS Color State Front Panel Control and Indicators Criticality 2. 3. 4. Amber Solid on Critical, nonrecoverable Description VRD Hot asserted. One of the redundant power supplies failed. Minimum number of fans to cool the system are not present or have failed. Fatal alarm – system has failed or shutdown BIOS Detected 1. DIMM failure when there is one DIMM present and no good 1 memory is present. 1 2. Run-time memory uncorrectable error in non-redundant mode. 3.
PAGE 53
® Intel Server Chassis H2000 Family TPS Appendix A: Integration and Usage Tips Appendix A: Integration and Usage Tips Before attempting to integrate and configure your system, you should reference this section, which provides a list of useful information.  Remove dummy tray cover before install node tray.  Install dummy tray cover when respective node tray is plugged out.  System fans in node trays are not hot-swappable.  You must use the CPU/memory air duct to maintain system thermals.
PAGE 54
® Intel Server Chassis H2000 Family TPS Glossary Glossary Term ACPI Advanced Configuration and Power Interface AP Application Processor APIC Advanced Programmable Interrupt Control ASIC Application Specific Integrated Circuit ASMI Advanced Server Management Interface BIOS Basic Input/Output System BIST Built-In Self Test BMC Baseboard Management Controller Bridge Circuitry connecting one computer bus to another, allowing an agent on one to access the other BSP Bootstrap Processor Byte
PAGE 55
® Glossary Intel Server Chassis H2000 Family TPS Term Definition IP Internet Protocol IPMB Intelligent Platform Management Bus IPMI Intelligent Platform Management Interface IR Infrared ITP In-Target Probe KB 1024 bytes KCS Keyboard Controller Style LAN Local Area Network LCD Liquid Crystal Display LED Light Emitting Diode LPC Low Pin Count LUN Logical Unit Number MAC Media Access Control MB 1024KB MCH Memory Controller Hub MD2 Message Digest 2 – Hashing Algorithm MD5 M
PAGE 56
® Intel Server Chassis H2000 Family TPS Term Glossary Definition SEL System Event Log SIO Server Input/Output SMI Server Management Interrupt (SMI is the highest priority non-maskable interrupt.
PAGE 57
® Reference Documents Intel Server Chassis H2000 Family TPS Reference Documents Refer to the following documents for additional information:  Intel® Server Board S2600JF Technical Product Specification (Intel Order Code: G31608)  Intel® Server System H2000JF Technical Product Specification (Intel Order Code: G39462)  Intel® Server Board S2600WP Technical Product Specification (Intel Order Code: G44057)  Intel® Server System S2000WP Technical Product Specification (Intel Order Code: 52418) 
PAGE 58
® Intel Server Chassis H2000 Family TPS Reference Documents  Intel® Thurley Server Platform Services IPMI Commands Specification, 2007. Intel Corporation.  Intel® Server Safety and Regulatory, 2011. Intel Corporation. (Intel Order Code: G23122)  Intelligent Platform Management Bus Communications Protocol Specification, Version 1.0, 1998. Intel Corporation, Hewlett-Packard Company, NEC Corporation, Dell Computer Corporation.