Technical Product Specification

ManualsBrandsIntel ManualsOtherIntel Server Board S2600IP4

Intel

Server System R2000IP

Product Family

Intel order number G38158-002

Revision 1.1

March 2014

Product Collaboration and System Division - Marketing

Summary of content (69 pages)

PAGE 1
Intel® Server System R2000IP Product Family Technical Product Specification Intel order number G38158-002 Revision 1.
PAGE 2
Revision History Intel® Server System R2000IP Product Family TPS Revision History Date Revision Number Modifications May 2012 1.0 Initial release. March 2014 1.1 Update E5-2600 v2 support and Corporation Information Disclaimers ® Information in this document is provided in connection with Intel products. No license, express or implied, by ® estoppel or otherwise, to any intellectual property rights is granted by this document.
PAGE 3
Intel® Server System R2000IP Product Family TPS Table of Contents Table of Contents 1. Introduction ........................................................................................................................ 1 1.1 Chapter Outline ...................................................................................................... 1 1.2 Server Board Use Disclaimer ................................................................................. 2 2. Product Family Overview ...................
PAGE 4
Table of Contents Intel® Server System R2000IP Product Family TPS 3.5.16 Electrostatic Discharge Susceptibility ................................................................... 22 3.5.17 Fast Transient/Burst ............................................................................................. 22 3.5.18 Radiated Immunity ............................................................................................... 22 3.5.19 Surge Immunity ........................................................
PAGE 5
Intel® Server System R2000IP Product Family TPS Table of Contents 4.1 Thermal Operation and Configuration Requirements............................................ 34 4.2 Thermal Management Overview .......................................................................... 35 4.2.1 Set Throttling Mode .............................................................................................. 36 4.2.2 Altitude ...............................................................................................
PAGE 6
List of Figures Intel® Server System R2000IP Product Family TPS List of Figures Figure 1. System Overview ......................................................................................................... 3 Figure 2. System Components Overview .................................................................................... 6 Figure 3. 3.5" Hard Drive Bay - 8 Drive Configuration ................................................................. 7 Figure 4. 3.
PAGE 7
Intel® Server System R2000IP Product Family TPS Table of Contents Figure 39. Internal SAS Expander Installation ........................................................................... 51 Figure 40. Internal 24-Port SAS Expander Card........................................................................ 51 Figure 41. 24-Port Expander SAS Connector/Drive Identification Block Diagram ...................... 51 Figure 42. Internal 36-Port SAS Expander Card..................................................
PAGE 8
List of Tables Intel® Server System R2000IP Product Family TPS List of Tables Table 1. System Feature Set....................................................................................................... 3 Table 2. Dimensional Data .......................................................................................................... 4 Table 3. System Environmental Limits Summary ........................................................................ 5 Table 4. P1 Baseboard Power Connector (P1)..
PAGE 9
Intel® Server System R2000IP Product Family TPS List of Tables Table 39. Drive Status LED States ............................................................................................ 46 Table 40. Drive Activity LED States........................................................................................... 46 Table 41. SAS Expander Support Options ................................................................................ 49 Table 42.
PAGE 10
List of Tables Intel® Server System R2000IP Product Family TPS x Revision 1.
PAGE 11
Intel® Server System R2000IP Product Family TPS 1. Introduction Introduction This Technical Product Specification (TPS) provides system level information for the Intel® Server System R2000IP product families. The system level features of both these product families are common, however the server board integrated into them is different. The Intel® Server System R2000IP product family is integrated with an Intel® Server Board S2600IP.
PAGE 12
Introduction 1.2 Intel® Server System R2000IP Product Family TPS Server Board Use Disclaimer Intel Corporation server boards support add-in peripherals and contain a number of high-density VLSI and power delivery components that need adequate airflow to cool. Intel® ensures through its own chassis development and testing that when Intel® server building blocks are used together, the fully integrated system will meet the intended thermal requirements of these components.
PAGE 13
Intel® Server System R2000IP Product Family TPS 2. Product Family Overview Product Family Overview The Intel® Server System R2000IP is rack mount 2U server systems. This generation of Intel® 2U server platforms offers a variety of system options to meet the varied configuration requirements of high-density high-performance computing environments. This chapter provides a high-level overview of the system features and available platform options as offered in different platform SKUs.
PAGE 14
Product Family Overview Intel® Server System R2000IP Product Family TPS Optional I/O Module Support The following I/O modules utilize a single proprietary on-board connector. An installed I/O module can be supported in addition to standard on-board features and any add-in expansion cards.
PAGE 15
Intel® Server System R2000IP Product Family TPS Product Family Overview Exposure to absolute maximum rating conditions for extended periods may affect system reliability. Table 3. System Environmental Limits Summary Parameter Limits Temperature Operating ASHRAE Class A2 – Continuous Operation. 10º C to 35º C (50º F to 95º F) with the maximum rate of change not to exceed 10°C per hour ASHRAE Class A3 – Includes operation up to 40C for up to 900 hrs per year.
PAGE 16
Product Family Overview Servers/Rack Mount BA Intel® Server System R2000IP Product Family TPS 7.0 7.0 7.0 7.0 Note: 1. Intel Corporation server boards contain a number of high-density VLSI and power delivery components that need adequate airflow to cool. Intel ensures through its own chassis development and testing that ® when Intel server building blocks are used together, the fully integrated system will meet the intended thermal requirements of these components.
PAGE 17
Intel® Server System R2000IP Product Family TPS 2.3.1 Product Family Overview Hot Swap Hard Drive Bay and Front Panel Options Figure 3. 3.5" Hard Drive Bay - 8 Drive Configuration Figure 4. 3.5" Hard Drive Bay - 12 Drive Configuration Figure 5. 2.5" Hard Drive Bay - 8 Drive Configuration Figure 6. 2.5" Hard Drive Bay - 16 Drive Configuration Figure 7. 2.5" Hard Drive Bay - 24 Drive Configuration Revision 1.
PAGE 18
Product Family Overview 2.3.2 Intel® Server System R2000IP Product Family TPS Back Panel Features Figure 8. Back Panel Feature Identification 2.3.
PAGE 19
Intel® Server System R2000IP Product Family TPS Product Family Overview ® Figure 10. Intel Server Board S2600IP Revision 1.
PAGE 20
Product Family Overview Intel® Server System R2000IP Product Family TPS Figure 11. Stand by LED, Fan Fault LED and CPU Fault LED Location 10 Revision 1.
PAGE 21
Intel® Server System R2000IP Product Family TPS Product Family Overview Figure 12. DIMM Fault LED’s Location Revision 1.
PAGE 22
Product Family Overview Intel® Server System R2000IP Product Family TPS Figure 13. Location of System Status, System ID and POST Code Diagnostic LEDs LED Name 2.5 A Description System Status LED B System ID LED LSB 1 2 3 4 5 6 MSB Post Code Diagnostic LEDs Front Bezel Support The optional front bezel is made of molded plastic and uses a snap-on design. When installed, its design allows for maximum airflow to maintain system cooling requirements.
PAGE 23
Intel® Server System R2000IP Product Family TPS 2.
PAGE 24
Power Subsystem 3. Intel® Server System R2000IP Product Family TPS Power Subsystem There is 750 Watt AC power supply module available. This chapter will provide the power supply specification details. The power supply will accept a wide input voltage range of 90 to 264Vac, while providing precisely regulated 12Vdc output voltage at 750W. The power supply will encompass all protective features and conform to safety agency regulatory requirements.
PAGE 25
Intel® Server System R2000IP Product Family TPS 3.2 Power Subsystem Power Distribution Board and Power Interface board 3.2.1 Input Connectors to Power Interface board (PSU mating connectors) Pin S1 Pin S13 Signal n.c. S14 n.c. S3 S4 S5 Signal +12V Remote Sense +12V Remote Sense Return 12V Load Share SMBAlert# SDA S15 S16 S17 A0 Present (not used) Vbias (not used) S6 SCL S18 n.c. S7 PSKILL (grounded) S19 n.c. S8 S9 S10 PSON PWOK A1 S20 S21 S22 n.c. n.c. n.c.
PAGE 26
Power Subsystem 3.2.2 Intel® Server System R2000IP Product Family TPS Connector from Interface Board to power distribution board Pin S1 S3 S4 S5 Signal +12V Remote Sense +12V Remote Sense Return SMBAlert# SDA SCL S6 PSON S14 n.c. S7 PWOK 1 S15 n.c. S8 P1 P2 PWOK 2 +12V output +12V output S16 P3 P4 n.c. Ground Ground S2 Pin S9 Signal 5VSB S10 5VSB S11 S12 S13 Vbias (not used) 5VSB 5VSB Figure 18. Power Distribution Board Interface Connector Pin-out on Interface Board 3.2.
PAGE 27
Intel® Server System R2000IP Product Family TPS Power Subsystem Connector No. of pins Description P1 24 Motherboard Main Power Connector P2 8 CPU1 Power Connector P3 8 CPU2 Power Connector P4 5 PMBus* Connector P5 4 Motherboard 2x2 12V power connector P6 6 HSBP power connector P7 4 Peripherals Power connector (CD, SSDs) Figure 19. Power Distribution Board Output Connectors 3.2.3.1 Power Distribution Board Connectors Pin definition Table 4.
PAGE 28
Power Subsystem Intel® Server System R2000IP Product Family TPS Table 7. 2x2 pin 12V Power Connectors (P5) Pin Signal Pin Signal 1 2 COM COM 3 4 +12V1 +12V1 Table 8. HSBP Power Connectors (P6) Pin 1 Signal COM Pin 4 Signal +12V2 (240VA) 2 COM 5 +12V3 (240VA) 3 COM 6 +12V3 (240VA) Table 9. Peripheral Power Connector (P7) 3.
PAGE 29
Intel® Server System R2000IP Product Family TPS Power Subsystem Figure 20. AC Power Cord 3.5 AC Input Requirement The power supply shall incorporate universal power input with active power factor correction which shall reduce line harmonics in accordance with the EN61000-3-2 and JEIDA MITI standards. 3.5.1 AC Inlet Connector The AC input connector shall be an IEC 320 C-14 power inlet. This inlet is rated for 15A/250VAC. 3.5.
PAGE 30
Power Subsystem 3.5.4 Intel® Server System R2000IP Product Family TPS Power Recovery The power supply will recover automatically after an AC power failure. AC power failure is defined to be any loss of AC power that exceeds the dropout criteria. 3.5.5 Voltage Brown Out The power supply shall comply with the limits defined in EN55024: 1998 using the IEC 61000-4-11:1995 test standard and performance criteria C defined in Annex B of CISPR 24.
PAGE 31
Intel® Server System R2000IP Product Family TPS Power Subsystem current requirements for any rated AC voltage, during turn-on at any phase of AC voltage, during a single cycle AC dropout condition as well as upon recovery after AC dropout of any duration, and over the specified temperature range Top, (includes hot and cold inrush). It is acceptable that AC line inrush current may reach up to 60A peak for up to 1msec. 3.5.
PAGE 32
Power Subsystem  Intel® Server System R2000IP Product Family TPS The surge-withstand test must not produce damage to the power supply. The supply must meet surge-withstand test conditions under maximum and minimum DC-output load conditions. 3.5.14 AC Line Isolation Requirements The power supply shall meet all safety agency requirements for dielectric strength.
PAGE 33
Intel® Server System R2000IP Product Family TPS Power Subsystem The pass criteria include: No unsafe operation is allowed under any condition; All power supply output voltage levels to stay within proper spec levels; No change in operating state or loss of data during and after the test profile; No component damage under any condition. The power supply shall comply with the limits defined in EN55024: 1998 using the IEC 61000-45:1995 test standard and performance criteria B defined in Annex B of CISPR 24.
PAGE 34
Power Subsystem Intel® Server System R2000IP Product Family TPS All outputs are measured with reference to the return remote sense signal (ReturnS). The +12V and +5Vsb voltages are measured at the PDB output harness connector. Table 17. Voltage Regulation Limits 3.6.6 Output Tolerance MIN NOM MAX Units + 12V ± 5% 11.40 12.00 12.60 VDC + 5Vsb ± 5% 4.75 5.00 5.
PAGE 35
Intel® Server System R2000IP Product Family TPS Power Subsystem stability with local sensing through the submission of Bode plots. Closed-loop stability must be ensured at the maximum and minimum loads as applicable. 3.6.11 Common Mode Noise The Common Mode noise on any output shall not exceed 350mV pk-pk over the frequency band of 10Hz to 20MHz. 1.
PAGE 36
Power Subsystem Intel® Server System R2000IP Product Family TPS In general, a failed (off by internal latch or external control) supply may be removed, then replaced with a good power supply, however, hot swap needs to work with operational as well as failed power supplies. The newly inserted power supply will get turned on into standby or Power On mode once inserted. 3.6.16 Timing Requirements These are the timing requirements for the power supply operation.
PAGE 37
Intel® Server System R2000IP Product Family TPS Power Subsystem AC Input Tvout_holdup Vout Tpwok_low TAC_on_delay Tsb_on_delay Tpwok_on PWOK 5VSB Tpwok_off Tsb_on_delay Tpwok_on Tpwok_holdup Tsb_vout Tpwok_off Tpson_pwok T5VSB_holdup Tpson_on_delay PSON AC turn on/off cycle PSON turn on/off cycle Figure 21. Turn On/Off Timing Diagram (Power Supply Signals) 3.6.
PAGE 38
Power Subsystem Intel® Server System R2000IP Product Family TPS shall be protected under over-current or shorted conditions, so that no damage can occur to the power supply. Table 22. Over Current Protection Limits Output Voltage +12V + 5Vsb OCP Limits 70A min; 78A max 4.5Amin; 6.5A max The OCP limits should be provided in both redundant and non-redundant mode. 3.7.2 Over-voltage Protection (OVP) The power supply over voltage protection shall be locally sensed.
PAGE 39
Intel® Server System R2000IP Product Family TPS Power Subsystem # Table 24. PSON Signal Characteristic Signal Type # PSON = Low # PSON = High or Open Logic level low (power supply ON) Logic level high (power supply OFF) Source current, Vpson = low Power up delay: Tpson_on_delay PWOK delay: Tpson_pwok 3.8.2 Accepts an open collector/drain input from the system. Pull-up to +3.3V located in power supply. ON OFF MIN MAX 0V 0.4V 2.4 V 3.
PAGE 40
Power Subsystem Intel® Server System R2000IP Product Family TPS regulation limits or when AC power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed, PWOK will be de-asserted to a LOW state. The start of the PWOK delay time shall inhibited as long as any power supply output is in current limit. Table 26.
PAGE 41
Intel® Server System R2000IP Product Family TPS 3.8.6 Power Subsystem SMBALERT Output Signal SMBALERT signal is open drain output signal to give an alert when any problem happens on PMBUS*. Table 29. SMBALERT Signal Characteristics Signal Type Open Drain Output Signal, Low active MIN 0V Logic level low voltage Logic level high voltage Sink current Vout_low = 0.4V 3.8.7 MAX 0.4V 3.46V 2mA Power Supply Status LED There will be a single bi-color LED to indicate power supply status.
PAGE 42
Power Subsystem Intel® Server System R2000IP Product Family TPS Table 31. Levels per load Total Load Ishare Minimum Ishare Maximum Number of supplies 100% 7.75V 8.25V 1 50% 3.90V 4.15V 1 0% 0.00V 0.50V 1 Note: The current share bus will not oscillate during application of AC, or during hot-plug. 3.9 3.9.1 Power Management Bus (PMBus*) Resolution and Range The resolution for all of the linear formatted commands is very wide. The following table puts boundaries on the expected data.
PAGE 43
Intel® Server System R2000IP Product Family TPS 3.9.2 Power Subsystem PMBus* Device Addressing The addressing method uses the 7 MSB bits to set the address and the LSB to define whether a device is reading or writing. The addresses defined below uses 7 bits (8 bits with LSB zero). Table 34. PMBus* Device Addressing Address A1/A0 PMBus* Address 3.9.
PAGE 44
Thermal and Acoustic Management 4. Intel® Server System R2000IP Product Family TPS Thermal and Acoustic Management The Intel Server System R2000IP is designed to operate at external ambient temperatures in compliance with ASHARE class A2. Working with integrated platform management, features within the system are designed to move air in a front to back direction, through the system and over critical components in order to prevent overheating and allow the system to operate with best performance. 4.
PAGE 45
Intel® Server System R2000IP Product Family TPS Thermal and Acoustic Management o   4.2 Add-in cards with a minimum 100 LFM (0.5 m/s) air flow requirement can be installed in any available add-in card slot o Add-in cards with a minimum 200 LFM (1 m/s) air flow requirement can be installed in any available add-in card slot. o Add-in cards with a >200 LFM air flow requirement cannot be supported. o Note: Most PCI add-in cards have minimum air flow requirements of 100 LFM (0.5m/s).
PAGE 46
Thermal and Acoustic Management Intel® Server System R2000IP Product Family TPS management technology (mechanism) is developed. Options reserved for end users to adjust parameter settings based on the actual system configuration and usage in BIOS interface with path: BIOS > Advanced > System Acoustic and Performance Configuration. Refer to below to setup the system thermally right. 4.2.
PAGE 47
Intel® Server System R2000IP Product Family TPS 4.2.6 Thermal and Acoustic Management Fan and HDD Configuration ® The Intel Server System R2000IR consists six 60x38mm system fans providing cooling for all ingredients inside the enclosure. All the fans are Pulse Width Modulated (PWM) 4 wire/pin fans. The fan headers are connected to motherboard with below sequence. Misconnect will potentially lead to thermal risk or undesired acoustic.
PAGE 48
Thermal and Acoustic Management Disk/Optical Gfx/add-in card Others PSU Declared Acoustic Intel® Server System R2000IP Product Family TPS SATA 3.5” (6x) PCI-e card (3x) Roc Mezz card 750W (2x) Idle: 5.7BA 3 TO1: 6.1BA 4 TO2: 6.2BA Notes: 1. System is at or below 900m altitude and set to acoustic mode. 2. Quiet Fan Idle Mode is enabled. 3. TO1 - Typical operating mode 1: processor and HDD stressed. 4. TO2 – Typical operating mode 2: processor, memory, HDD stressed. 38 Revision 1.
PAGE 49
Intel® Server System R2000IP Product Family TPS 4.3 Cooling Sub-System Processor Heatsink A heatsink is included in the system package. This heatsink is designed for optimal cooling and performance. To achieve better cooling performance, you must properly attach the heatsink bottom base with TIM (thermal interface material), the heatsink is required if necessary. Figure 23. Processor Heatsink Overview 4.4 System cooling Fans Six 80x38-mm fans provide the primary airflow for the system.
PAGE 50
Cooling Sub-System     Intel® Server System R2000IP Product Family TPS Fan speed for each fan is controlled by integrated platform management as controlled by the integrated BMC on the server board. As system thermals fluctuate high and low, the integrated BMC firmware will increase and decrease the speeds to specific fans within the fan assembly to regulate system thermals. Each fan has a tachometer signal that allows the Integrated BMC to monitor their status.
PAGE 51
Intel® Server System R2000IP Product Family TPS 5. System Storage and Peripheral Drive Bays System Storage and Peripheral Drive Bays The Intel® Server System R2000IP4 product family has support for many storage device options, including:      Hot Swap 2.5'' Hard Disk Drives Hot Swap 3.
PAGE 52
System Storage and Peripheral Drive Bays Intel® Server System R2000IP Product Family TPS Figure 27. 2.5" Hard Drive Bay - 24 Drive Configuration The drive bay can support either SATA or SAS hard disk drives. Mixing of drive types within the hard drive bay is not supported. Hard disk drive type is dependent on the type of host bus controller used, SATA only or SAS. Each 2.5” hard disk drive is mounted to a drive tray, allowing for hot swap extraction and insertion.
PAGE 53
Intel® Server System R2000IP Product Family TPS System Storage and Peripheral Drive Bays Table 38. Drive Activity LED States Condition Power on with no drive activity Power on with drive activity Green Power on and drive spun down Power on and drive spinning up 5.1.1 Drive Type Behavior SAS SATA SAS SATA SAS SATA SAS SATA LED stays on LED stays off LED blinks off when processing a command LED blinks on when processing a command LED stays off LED stays off LED blinks LED stays off 2.
PAGE 54
System Storage and Peripheral Drive Bays Intel® Server System R2000IP Product Family TPS Label Description A SMBus*-out cable connector – From Server board or other backplane B 4-port Mini-SAS cable connectors C SMBus*-in cable connector for multi-backplane support D Power connector Figure 30. 2.
PAGE 55
Intel® Server System R2000IP Product Family TPS System Storage and Peripheral Drive Bays Label A Description System label pull-out B SATA Optical Drive C USB Ports D E Front Control Panel 3.5” Hard Drive Bays Figure 31. 3.5" Hard Drive Bay - 8 Drive Configuration Label Description A 3.5” Hard Drive Bays B Front Control Panel Figure 32. 3.5” Hard Drive Bay - 12 Drive Configuration The drive bay can support either SATA or SAS hard disk drives.
PAGE 56
System Storage and Peripheral Drive Bays Intel® Server System R2000IP Product Family TPS Figure 33. 3.5” Hard driver installation Light pipes integrated into the drive tray assembly direct light emitted from Amber drive status and Green activity LEDs located next to each drive connector on the backplane, to the drive tray faceplate, making them visible from the front of the system. Amber Status LED Green Activity LED Table 39.
PAGE 57
Intel® Server System R2000IP Product Family TPS System Storage and Peripheral Drive Bays Figure 34. 3.5” Drive Hot-Swap Backplane Overview Behind each backplane are several connectors. The following illustration identifies these connectors. Label Description A Power connector B 4-port mini-SAS connectors C SMBus* connector Figure 35. 3.5” Hard Drive Backplane backside A – Power Harness Connector - The backplane includes a 2x2 connector supplying power to the backplane.
PAGE 58
System Storage and Peripheral Drive Bays 5.3 Intel® Server System R2000IP Product Family TPS Optical Drive Support (optional) Systems configured with eight 3.5” hard drive bays or up to sixteen 2.5” hard drive bays also include support for an optical drive bay ‘A’ as illustrated below. Figure 36. Opitcal driver support 5.4 eUSB SSD Suport The system provides support for an eUSB SSD storage device.
PAGE 59
Intel® Server System R2000IP Product Family TPS System Storage and Peripheral Drive Bays Table 41. SAS Expander Support Options Intel® SAS Expander 24 Port PCIe Intel RAID Expander Card RES2SV240 Installation type PCIe add-in card Hard Drive Configuration 3.5” Hard Disk drive bay configurations ® Internal mount 2.5” Hard Disk drive bay configurations ® Internal mount 2.5” Hard Disk drive bay configurations ® 24 Port Internal Intel RAID Expander 36 Port Internal Intel RAID Expander 5.5.
PAGE 60
System Storage and Peripheral Drive Bays Intel® Server System R2000IP Product Family TPS contiguous drive mapping (0 – 12), cable routing differs when using a x8 wide-port capable 6 Gb SAS/SAS RAID Controller vs. using the embedded SCU ports. 5.5.1.
PAGE 61
Intel® Server System R2000IP Product Family TPS System Storage and Peripheral Drive Bays Figure 39. Internal SAS Expander Installation The following diagrams are used to help identify the mini-SAS connectors found on the SAS expander cards. Care should be taken when connecting connectors from the SAS expander to the connectors on the backplane because each connector is pre-programmed at the factory to provide specific drive identification mapping.
PAGE 62
System Storage and Peripheral Drive Bays Intel® Server System R2000IP Product Family TPS Figure 42. Internal 36-Port SAS Expander Card 0-3 4-7 24-27 28-31 32-35 A B G H I SAS 8 7 36-port 6 6Gb 0 Expander 5 1 4 2 3 8-11 12-15 16-19 20-23 C D E F Figure 43. 36-Port Expander SAS Connector/Drive Identification Block Diagram Each connector on the SAS expander card can be used as a “cable in” (SAS Controller to SAS Expander) or “cable out” (SAS Expander to Hot Swap Backplane) type connector.
PAGE 63
Intel® Server System R2000IP Product Family TPS System Storage and Peripheral Drive Bays  Cables from the SAS Expander to the hot swap backplane must be connected in order: B – E for 16-drive configurations, and B – G for 24 drive configurations.  The SCU_0 or 3G SAS/SAS RAID (0-3) connector is cabled to the first mini-SAS connector on the hot swap backplane The SCU_1 or 3G SAS/SAS RAID (4-7) connector is cable to Connector A on the SAS expander card.
PAGE 64
Front Control Panel and I/O Panel Overview 6. Intel® Server System R2000IP Product Family TPS Front Control Panel and I/O Panel Overview All system configurations will include a Control Panel on the front of the system providing push button system controls and LED indicators for several system features. Systems configured with eight 3.5” hard drive bays or up to sixteen 2.5” hard drive bays will also include an I/O Panel providing additional system I/O features.
PAGE 65
Intel® Server System R2000IP Product Family TPS Front Control Panel and I/O Panel Overview Label A Description System ID Button w/Integrated LED Label F Description System Status LED B NMI Button (recessed, tool required for use) G Power/Sleep Button w/Integrated LED C NIC-1 Activity LED H Hard Drive Activity LED D NIC-3 Activity LED I NIC-4 Activity LED E System Cold Reset Button J NIC-2 Activity LED Figure 45.
PAGE 66
Front Control Panel and I/O Panel Overview Intel® Server System R2000IP Product Family TPS G – Power/Sleep Button – Toggles the system power on and off. This button also functions as a sleep button if enabled by an ACPI compliant operating system. Pressing this button will send a signal to the integrated BMC, which will either power on or power off the system. The integrated LED is a single color (Green) and is capable of supporting different indicator states as defined in the following table. Table 43.
PAGE 67
Intel® Server System R2000IP Product Family TPS Appendix A: Integration and Usage Tips Appendix A: Integration and Usage Tips This section provides a list of useful information that is unique to the Intel® Server System R2000IP Product Family and should be kept in mind while configuring your server system.           Only the Intel® Xeon® processor E5-2600 and E5-2600 v2 product family are supported in this Intel server system. Previous generation Intel® Xeon® processors are not supported.
PAGE 68
Glossary Intel® Server System R2000IP Product Family TPS Glossary Word/Acronym Definition ACA Australian Communication Authority ANSI American National Standards Institute BMC Baseboard Management Controller BIOS Basic Input/Output System CMOS Complementary Metal-oxide-semiconductor D2D DC-to-DC EMP Emergency Management Port FP Front Panel FRB Fault Resilient Boot FRU Field Replaceable Unit 2 IC Inter-integrated Circuit bus LCD Liquid Crystal Display LPC Low-pin Count LSB Lea
PAGE 69
Intel® Server System R2000IP Product Family TPS Reference Documents Reference Documents See the following documents for additional information:          Intel® Server Board S2600IP Technical Product Specification Intel® Server System R2000IP Product Family Spares/Parts List and Configuration Guide Intel® Server System R2000IP Service Guide Intel® Server System R2000IP Quick Installation Guide BIOS for Intel○R Server Platforms Based on Intel® Xeon Processor E54600/2600/2400/1600 Product Families