Qsug

ManualsBrandsIntel ManualsOtherIntel Server Board S2600COE

Software

• BIOS, Drivers, and Operating System Installation

A. Conﬁrm BIOS Version: Look on the Server/System Management screen in the BIOS

Setup Utility to determine the installed BIOS version. Compare this to the versions at:

http://www.intel.com/support/motherboards/server.

If new versions are available, update the BIOS on your server. See the Techinical Product Speciﬁcation

on the Intel

Server Deployment Toolkit CD for update instructions.

B. Conﬁgure your RAID Controller:

Use the instructions provided with the RAID controller.

C. Install your Operating System:

Use the instructions provided with the RAID controller

and with the operating system.

D. Install Operating System Drivers: With the operating system running, insert the

Intel

Server Deployment Toolkit CD. If using a Microsoft Windows* operating system, the Intel

Deployment Assistant will autorun and allow you to select the appropriate drivers to install. On other

operating systems, browse the CD folders to locate and install the driver ﬁles.

Side 2

STOR_UPG_KEY

Locate the white-colored four-pin key header near DIMM_C1 slot.

Match the Key and connector orientation and press down to install.

Install Add-in

Card[s]

See the documentation that came with your

server chassis for add-in card installation.

For the Intel

Server Chassis P4000M

series, see the Quick Installation User's

Guide accompanying the chassis.

Install Optional

Components

Follow the Intel

Trusted Platform Module Hardware

User’s Guide to install the TPM module.

Follow Intel

Remote Management Module 4 User

GUide to install RMM4 modules.

Follow the instructions come along with the eUSB SSD

device to install eUSB SSD.

Finishing Up

CAUTION: See your chassis

documentation for AC power and

grounding requirements.

Network

USB 0

USB 1

USB 2

USB 3

NIC1

10/100/

1000 Mb

NIC2

10/100/

1000 Mb

NIC3

10/100/

1000 Mb

NIC4

10/100/

1000 Mb

Video

Serial A

Before installing your operating

system, you must ﬁnish your chassis

installation, make I/O connections and

plug in AC power.

See your chassis documentation for AC

power and grounding requirements.

Common Problems and Solutions

The system does not boot or show video at power-on.

•

Check that the +12V CPU power connector is plugged in. Without this cable, the processors will not have any power.

•

Only Intel

Xeon

Processor E5-2600 series

with 135 W and less Thermal Design Power (TDP) are supported on S2600CO4.

Previous generation Intel

Xeon

processors are not supported.

•

Only Intel

Xeon

Processor E5-2600 series

with 150 W and less Thermal Design Power (TDP) are supported on S2600COE.

Previous generation Intel

Xeon

processors are not supported.

Beep code 1-5-2-1 in a system means you do not have Intel

Xeon

Processor E5-2600 series

installed.

•

The system generates the memory error beep code and POST diagnostic LED message {0XE0~0XEF} that indicates memory errors in early POST.

•

Remember, all DIMMs must be:

•

DDR3 800/1066/1333/1600 MHz ECC UDIMM/RDIMM/LRDIMM.

•

From the same manufacturer.

•

Installed beginning with DIMM A1.

For a list of hardware components that have been tested with

this system, see:

http://www.intel.com/support/motherboards/server

CPU 1 Socket

CPU 2 Socket

Main Power

Connector Detail

Latch

Tab

CPU Power

Connector Detail

Make Server Board

Power Connections

Attach the CPU 1 power connector.

Attach the CPU 2 power connector.

CAUTION:

Note the location of the

latch on each power cable

connector and align it with the matching

tab on each server board socket.

Attach the main power connector.

IMPORTANT NOTE:

If you are using a

non-Intel server chassis with an ATX

power supply, see the documentation

that came with your chassis for

installation information.

Server

Board

SAS/SATA 0

SAS/SATA 1

SAS/SATA 2

SAS/SATA 3

SAS/SATA 4*

SAS/SATA 5*

SAS/SATA 6*

SAS/SATA 7*

SATA 1**

SATA 0**

Connect Hard Drives/Optical Drive to

Server Board

Connect SAS/SATA Data Cables to server board here.

NOTE:

* SATA/SAS functionality on ports 0-7 requires

purchase of an optional Intel

RAID C600

Upgrade Key.

** 6Gb/s SATA port.

Server

Board

System Fan 1-6

Connector

Detail

System Fan 7

Connector

Detail

Chassis Fan Connections

For a non-Intel server chassis, see the documentation accompanying your chassis for speciﬁc chassis

fan connection requirements. Refer to the "Making Connections to the Server Board - Quick Reference"

section below.

CPU 1 Socket

CPU 2 Socket

C1DIMM C2 D1 D2

B2DIMM B1 A2 A1

E1DIMM E2 F1 F2

H2DIMM H1 G2 G1

Memory Conﬁgurations and Population Order:

Note: For additional memory conﬁgurations, see the

Techinical Product Speciﬁcation for Intel

Server

Board S2600CO at:

http://www.intel.com/support/motherboards/server.

Memory sizing and conﬁguration is supported only for

qualiﬁed DIMMs approved by Intel

. For a list of

supported memory, see the tested memory list at

http://serverconﬁgurator.intel.com/default.aspx

Memory Type: Minimum of one 1 GB,

DDR3 800/1066/1333/1600 MHz

ECC UDIMM/RDIMM/LRDIMM.

Install DIMM Memory Modules

DDR3 DIMM Memory Identiﬁcation:

DIMM

notch and

socket

bump must

be aligned as

shown.

Other

Memory

DDR3

This server board supports up to 16 DDR3 1066/1333/1666 ECC

UDIMM/RDIMM/LRDIMM.

CAUTION: Observe normal ESD (ElectroStatic Discharge) procedures

to avoid possible damage to system components.

Install Optical

Drive and

Hard Drive(s)

See the documentation that came

with your server chassis for drive

installation.

Making Connections to the Server Board — Quick Reference

Internal

USB

Connector

Detail

USB

Connector

Detail

Front Panel

Connector

Detail

Attach Front Panel, and USB Connections

Note: For a non-Intel

chassis, see your

chassis documentation

for front panel features

and server board

connection requirements.

Install Intel® RAID C600

Upgrade Key (Optional)

Make this connection to the P4000M series

chassis with ﬁxed system fan conﬁguration.

Make this connection to the P4000M series chassis

with hotswap fans, backplane(s), power supply(s)

Make this connection when applicable

= Make this connection

Intel

Server Chassis

P4000M series

A. CPU 1-2 Power Connector

B. Main Power Connector

C. Front Panel Header

Required Connections

Intel

Server Chassis

P4000M series

Optional Connections

D. System Fan 1 Header

E. System Fan 2 Header

F. System Fan 3 Header

G. System Fan 4 Header

H. System Fan 5 Header

I. System Fan 6 Header

J. System Fan 7 Header

K. CPU 1 Fan Header

L. CPU 2 Fan Header

M. Serial B

N. Storage Upgrade Key

O. USB 5/6 (Front Panel)

P. IPMB

Q. SAS/SATA Connectors

R. SATA 6G

S. RMM4 Lite

T. Chassis Intrusion

U. RMM4 NIC

V. HSBP_I

W. SAS SGPIO

X. eUSB SSD

Y. TPM

Z. USB 4 (Type A)

AA. LCP

AB. PMBus

AC. FAN BOARD_I

AD. IEEE_1394B

IMPORTANT Note:

Cables should be

tied for better airﬂow.

Use cable-ties compulsorily.

Note: For a non-Intel Chassis, see your chassis documentation for server board

connection information.

Note: All optional connections are not shown in this diagram. Refer to your

Server Board Service Guide, and your server chassis documentation for

additional connection information.

Cable Routing in Intel

Server Chassis P4000M series with

Fixed Fans, Fixed HDDs, Fixed PSU

Description

A. CPU1/CPU2 Power Cable

B. Server Board Main Power Cable

(Power extend cable is needed)

C. Fixed HDD Power Cable

D. ODD Power Cable

E. Front Panel Cable, USB Cable

F. ODD Data Cable (Connect To White

SATA 6G Connectors On Server Board)

Description

G. Fixed HDD Data Cable

H. System FAN 1

I. System FAN 2

J. IEEE_1394B cable (Optional, Connect to

RMM4/IEEE_1394B connector on P4000M

chassis back panel)

AE. Optional 12V Power

DIMM E1

DIMM E2

DIMM F1

DIMM F2

DIMM H2

DIMM H1

DIMM G2

DIMM G1

DIMM B2

DIMM B1

DIMM A2

DIMM A1

DIMM C1

DIMM C2

DIMM D1

DIMM D2

FAN BOARD_I

(Intel

Server Board

S2600CO4 only)

Front Panel

Chassis Intrusion

RMM4 Lite

CPU 2 Fan

Sys Fan 7

CPU 2 Power

Serial B

RMM4 NIC

USB 5/6

Storage Upgrade Key

CPU 1 Power

Sys Fan 4

Sys Fan 6

Sys Fan 5

SAS SGPIO

Sys Fan 2

Sys Fan 1

Sys Fan 3

IPMB

HSBP_I

SAS/SATA

SATA

Main Power

USB 4

PMBus

Optional 12V Power

LCP

TPM

eUSB SSD

CPU 1 Fan

IEEE_1394B

(Intel

Server Board

S2600COE only)

Cable Routing in Intel

Server Chassis P4000M series with Hotswap

Fans, backplane(s), redundant PSU(s)

Server Board

Power

Supply

CPU2 CPU1

Main Power

Front

Panel

SAS/

SATA

USB

1394B

FAN_2

FAN_1

Server Board

Power Supply

CPU2 CPU1

Main Power

Front

Panel

SAS/

SATA

SGPIO

HSBP_I

USB

1394B

PMBus

FAN_3

FAN_4

FAN_5

FAN_2

FAN_1

I. HSBP_I

C Cable (5pin to 3pin, provide connection

from hot-swap back plane to server board )

J. HSBP_I

C Cable (5pin to 5pin, only for the chassis

with 2 hot-swap back plane cascade)

K. System FAN 1 L. System FAN 2

M. System FAN 3 N. System FAN 4

O. System FAN 5

P. IEEE_1394B cable (Optional, Connect to RMM4/IEEE_1394B

connector on P4000M chassis back panel)

Description Description

A. CPU1/CPU2 Power Cable

B. Server Board Main Power Cable (Power extend cable is needed)

C. Backplane Power Cable

D. ODD Power Cable

E. Front Panel Cable, USB Cable

F. ODD Data Cable (Connect To White SATA 6G Connectors

On Server Board)

G. Hotswap HDD Data Cable and SGPIO

H. PMBus Cable