Quick Integration Guide

ManualsBrandsIntel ManualsOtherIntel RAID Controller RS3SC008

Thank you for buying an Intel® RAID Maintenance Free Backup Unit 4. The Intel® RAID

Maintenance Free Backup Unit 4 supports the Intel® RAID Controller RS3DC040 and

RS3DC080. The following information will help you assemble your Intel

RAID

Maintenance Free Backup Unit 4 and install components.

Perform all installation work at an electrostatic discharge (ESD)-safe workstation that

meets the requirements of EIA-625, Requirements for Handling Electrostatic

Discharge Sensitive Devices. You must perform all actions in accordance to the latest

revision of the IPC-A-610 ESD-recommended practices.

This guide and other supporting documents are located on the web at:

http://www.intel.com/support.

H24048-001

Intel® RAID Maintenance Free Backup

Unit 4 Quick Installation User's Guide

Summary of content (12 pages)

PAGE 1
Intel® RAID Maintenance Free Backup Unit 4 Quick Installation User's Guide Thank you for buying an Intel® RAID Maintenance Free Backup Unit 4. The Intel® RAID Maintenance Free Backup Unit 4 supports the Intel® RAID Controller RS3DC040 and RS3DC080. The following information will help you assemble your Intel® RAID Maintenance Free Backup Unit 4 and install components.
PAGE 2
(This page is intentionally left blank.
PAGE 3
Table of Contents Product Overview ............................................................................................................................. 1 General Installation Process ........................................................................................................ 2 Unpack the RMFBU4 Module ......................................................................................... 2 Prepare the Host Computer ......................................................................
PAGE 4
Warning Warning Caution Read all caution and safety statements in this document before performing any of the instructions. Also see the Intel ® Server Board and Server Chassis Safety Information document at: http://www.intel.com/support/ motherboards/server/sb/cs-010770 .htm for complete safety information. Installation and service of this product to be performed only by qualified service personnel to avoid risk of injury from electrical shock or energy hazard.
PAGE 5
Product Overview The Intel® RAID Maintenance Free Backup Unit 4 (RMFBU4) is an Open NAND Flash Interface (ONFI) flash module that provides cache off-load capability to protect cached data in case of host power loss or server failure. The RMFBU4 module connects to a Super Capacitor Pack module, which provides power for the backup of your data.
PAGE 6
General Installation Process 1 4 Unpack the RMFBU4 Module CAUTION: It is good practice to back up your data before adding hardware, such as an RMFBU4 module, to your system. Unpack the RMFBU4 module in a static-free environment. Remove the module from the antistatic bag, and inspect it for damage. If the module appears to be damaged, contact Intel or your reseller support representative. 2 Attach the RMFBU4 Module to the RAID Controller A Ground yourself, and make sure that the system is grounded.
PAGE 7
General Installation Process 5 6 Install the Clip on the Remote Mount Board Attach the Super Capacitor Pack Module to the Clip A Ground yourself, and make sure that the system is grounded. A Ground yourself, and make sure that the system is grounded. B Place the clip and the remote mount board module front-side-up on a flat, clean, static-free surface. B Place the Super Capacitor Pack module and the clip front-side-up on a flat, clean, static-free surface.
PAGE 8
General Installation Process 7 8 Connect the RMFBU4 Module to the Remote Super Capacitor Pack Module (Valid for Remote Mount Board) A Ground yourself, and make sure that the system is grounded. B Place the RAID controller on a flat, clean, static-free surface. C Remove the cable that is included in the RAID controller box. D Insert one 9-pin cable connector on the cable into the 9-pin J1 connector on the RMFBU4 module, as shown in the following figure (the cable is blue).
PAGE 9
General Installation Process 9 Install the Remote Mount Board on the Motherboard A Make sure that the power to the chassis is still turned off, the power cords are unplugged, and the chassis is grounded and has no AC power. B Insert the remote mount board in a PCIe slot on the motherboard, as shown in the following figure.
PAGE 10
General Installation Process 11 Connect the RMFBU4 Module to the 12 Reinstall the RAID Controller on the Remote Super Capacitor Pack Module (Valid for Intel® Server Chassis) A Ground yourself, and make sure that the system is grounded. B Place the RAID controller on a flat, clean, static-free surface. C Remove the cable that is included in the RAID controller box.
PAGE 11
Reference Documents If you need more information about any topic covered in this guide, refer to the following documentation on the Intel website at http://www.intel.
PAGE 12
H24048-001